Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

OT-Fixing Dent in Truck Fender

Posts

OT-Fixing Dent in Truck Fender

#1

OT-Fixing Dent in Truck Fender

howard

>some turkey must have backed into my rear left fender on my tundra and left a nice dent - son of a bxxxh!!! my body guy says it will cost $775 to repair. Being that I have a well outfitted shop and have done tons of home based everything, is this a DIY type thing? Would it make sense for me to pull the dent and Bondo and let him paint it? I have good HVLP units, if I can spray lacquer for furniture, is this the same skill as spraying auto paint. Appreciate your thoughts, looking to save a few bucks but don't want to get in over my head. thanks again.

Re: OT-Fixing Dent in Truck Fender

#2

Re: OT-Fixing Dent in Truck Fender

Larry in NW Ohio

>Howard First off, I would assume you checked with your insuranse first, to see what they, if anything, they would cover. Good luck with it. Larry

Re: OT-Fixing Dent in Truck Fender

#3

Re: OT-Fixing Dent in Truck Fender

Joseph Mulherin, Sr

>Howard, yrs ago I had almost the same thing happen to my truck. What I did was to find a large suction cup(like a toilet plunger) cleaned off the dent with water then applied the suction cup to the dent and tugged it until the dent popped out. This can be done IF the metal has not been creased....even then you can get most of the dent out, then take actions to smooth out as needed. Repainting, if needed, will be sanding smooth all around edges too to blend paint, spray on undercoat, then sand very lightly, then spray you color. Mine turned out fine and didn't cost anything more that suction cup and paints.

A poor man will do almost anything he can to achieve a solution to his problem.

Re: OT-Fixing Dent in Truck Fender

#4

Get some books from the library

Bill Houghton, Sebastopol, CA

>This isn't hard, but there are subtleties; my local library has some decent books on the subject, and I bet yours does too. Look for recent publication dates and prefer those - I understand there's been a lot of change in this area (when I did the work on my cars some years back, one of the books I found had a long discussion of how to apply and smooth the solder that was used before Bondo - not super-helpful...).

I found, in the few repairs I did, that blending the edges of the paint job was the hardest, though I should mention that I didn't have a spray rig, using the touchup bottles auto paint stores sell; if the dent's big enough, you might find it easiest to mask off and repaint the whole fender.

Re: OT-Fixing Dent in Truck Fender

#5

Re: OT-Fixing Dent in Truck Fender

Pete in Holland, MI

>Before you jump into this, check out what you will spend for car paint. A quart of paint, clear coat, reducer will probably blow your socks off !

Re: OT-Fixing Dent in Truck Fender

#7

Re: OT-Fixing Dent in Truck Fender *LINK*

Mark Nowicki

>You are not are going to save any money. By the time you get proper equipment, run around town, etc. you will end up making 10 cents an hour.

Once, I offered my electrician my help. He said he did not mind charging for two men. I never offered again. Your body guy might feel the same way.

Mark


Auto body stuff

Re: OT-Fixing Dent in Truck Fender

#8

Re: OT-Fixing Dent in Truck Fender

GalenV in Iowa

>I don't know where you are located but do you have a high school or community collage or trade school that does body work? I know for a while they were looking for body work to train people. I know several poeple who had work done this way and it worked out fine. You just may be without the transportation for longer than a commercial shop. Maybe shorter time than if you did it yourself though.

Galen

Re: OT-Fixing Dent in Truck Fender

#9

Re: OT-Fixing Dent in Truck Fender

DonSTL

>Sorry for the delayed response, I just didn�t have time yesterday.

My experience with auto body is (was, as I haven�t done any for a long time) as a serious hobbyist. I have replaced fenders, quarter panels (rear fenders to the layman), rear clips, door panels, rocker panels, etc. I have spot painted, panel painted, and done over-all paint jobs on cars, trucks, and vans, including a few van murals (wasn�t that an interesting era).

You don�t state the age or condition of your truck, but that should have some bearing on your decision to do your own work, because the quality of your repair job will affect the resale/trade-in value of the vehicle.

One of the best suggestions made was to gather information, such as from the library.

Everyone has different standards and I don�t want to offend anyone, but I find auto body repair/refinishing to be much more critical than woodworking/wood finishing.

Finished wood inherently has imperfections that are expected. And, unless a wood item has a French polished finish, imperfections are not nearly as noticeable as on a vehicle with a high gloss finish.

Regarding the actual metal repair, depending on how deep the dent is and if the metal is creased or not will have an effect on how much the metal may be stretched. With the advent of thinner and thinner metal to lower vehicle weight, it has become harder and harder (almost impossible) to �shrink� the metal back to size by working it with a dolly and hammer.

To use body filler, the panel must be ground down to the bare metal with about a 36 grit disk. Filler will ONLY adhere to bare, clean metal. This generally means grinding outside of the damaged area.

The body filler must be mixed with hardener and applied in a matter of minutes. There is no time to smooth and shape until the end result looks just right. This is where experience comes in.

The filler must be sanded with coarse paper to a �roughed-in� shape and then finished using progressively finer grades of paper. Sanding blocks as long as approx. 15-inches are used to blend into surrounding areas.

Finally, spot fillers are used for any minor imperfections and then primer surfacer is used to help �feather-edge� a transition between the body filler and the existing finish.

When you can paint, experience will dictate whether to spray and blend into the surrounding area, back-tape along a panel ridge and spray just a panel section, or spray a complete panel.

The new finishes are catalyzed paint, i.e., a hardener must be mixed with the paint. Your paint may be available as a �one-step� mix, which means the color and clear coat are combined, or you may have to use a two-step mix, i.e., the color must be sprayed, then the clear coat must be sprayed.

I recently purchased a pint of one-step paint, one-half pint of hardener and a quart of reducer (thinner) and paid over $60.

By the way. If your truck is a metallic color, be aware that how well your sprayed color matches the rest of your truck will be determined by the reducer you use, the air pressure you use, the humidity and temperature at the time you spray, and your spraying technique, i.e., how wet you lay down the coats of paint, the distance you hold the gun from the panel, etc.