Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Workshop Building- need help!

Posts

Workshop Building- need help!

#1

Workshop Building- need help!

Chicago Bob

>For health reasons (back problems) I have had to retire unexpectedly at 59. Over the next year we plan to move back south from the suburbs of Chicago after being away from East Tennessee for 25+ years.

I would like to build a stand alone woodworking shop building of 700 to 1000 sq ft, roughly. Needless to say, budget will be tight.

I am looking for suggestions on type of constuction (pole, stick built, metal, etc.) which will keep costs as reasonable as possible. Need a wood floor to help with the back problems.

Any advice, experiences, what you would do different, cost per sq ft for various types of construction, etc would be valued.

Thanks in anticipation of your help.

Regards

Bob

Re: Workshop Building- need help!

#2

Re: Workshop Building- need help!

steve mackay

>I don't know . . . BIL just had a Morgan put up for his "workshop". Don't like it, cost a bunch (more than he planned on after it was said and done). Guess I'm just a "stick" guy. Plan it and build it "your way".

Re: Workshop Building- need help!

#3

Re: Workshop Building- need help!

Mac in Indy

>I don't like metal buildings. Without a lot of add ons (insulation & interior stud walls) they are not user friendly but they can be pretty cheap. Wood pole barns with metal outside fall in that same category for me.

Like the previous respondant I'm a stick built guy. Especially if you can do a lot of it yourself. It is what most of us are used to when building repairing or remodeling.

If it's warm enough in TN in the winter a standard joist floor up 3' on concrete piers let's you run Dust collection and electrical under the floor while remaining accessable for changes in shop layout. I'd have it just the right height for a pickup truck loading dock on one wall. Plan for a lot of windows for natural lighting. Put in a bathroom and finishing room if you can but that would make it bigger than you are planning.

Make scale drawings of what ever you plan on building. Cut out scale top views of your power tools and then a scale sheet of plywood along with an 8' and 10' long board to see how the flow of materiels would work. And don't under light the place. Old eyes need lots of light!

There was a guy on Sawmill Creek that doccumneted a shop build like this only much larger a couple of years ago. I can't remember his name and couldn't find it when searched. I think he moved over to Family woodworking forum a some point so you could ask around there. He had some great ideas and created a huge thread, thousands of replies. His was more of a one man pro shop.

Enjoy your retirement and shop build!

Mac

Re: Workshop Building- need help!

#4

Re: Workshop Building- need help!

Mac in Indy

>Found it!

Marty Walsh's "Birth of a Shop". Starts on Sawmill Creek and finishes up on Family Woodworking.

Re: Workshop Building- need help!

#5

Re: Workshop Building- need help!

Thomas Skaggs, Foothills of Mount Level

>Whatever method you choose I think it's a good idea to build as much space as you can afford. The idea of adding on later rarely ever happens.

Tom

Re: Workshop Building- need help!

#6

Re: Workshop Building- need help!

Fred Davis

>Bob,

here's a few shots of what I put up about ten years ago , taking into consideration , strain on legs and feet and a level and firm floor .

The building is stick built , 36x48 , scissor truss roof assembly with four skylights, ten foot side walls rising to fourteen feet inside the shop.

Six" slab on a sand fill , with 2x4 sleepers on 24"O.C. covered with 241 grade of 1 1/8" plywood decking. I made floor tiles 16" square of 1/8" tempered Masonite and painted with Porter Paints recommended two part epoxy floor paint.

This approach gives a firm floor to heavy machinery and a easy one for the feet and legs to stand on and it is warm.

Shop has a Bryant 95+ gas furnace, three ton A.C., overhead commercial fans , and a powerful vented to the outside fan.

The dust collection is a Oneida Industrial cyclone with a six bag filter, plus a Jet 2000 air cleaner mounted over the table saw and work bench area.

Main room is 36x42 with a tool/furnace room, paint room and wash room with a W.C. room within it.

Framing was 2x6 walls with R-19 fibreglas insulation and R-30 in the shallow attic.

This is the fifth shop I have owned, the third one I personally built and the smallest and most efficient of then all.

Feel free to email any questions about your project .

FredD

Re: Workshop Building- need help!

#9

Re: shop pics

Stuart Hough

>Great shop Fred! Sorta looks like the proverbial "heavenly place" to be!

Re: Workshop Building- need help!

#10

Re: Workshop Building- need help!

Jerry Gibbs

>2 thoughts. First, check with the building inspector as to what is allowed before planning too much. the second is if budget is tight and you build a large building, make a smaller enclosure for a wood floor and heating etc. you can store lumber and put the planer in the dirt portion. jerry gibbs

Re: Workshop Building- need help!

#11

Re: shop pics

George@Colonel's WorkshopHavertown PA

>Good Afternoon Fred,

We need more of the inside organization, Fred. What I see is great. that building is lovely, and looks like it has the room to contain about 15 of my shops. That dust ciollection system looks very "official".

George

Re: Workshop Building- need help!

#12

where are you moving to?

Bill Tindall, E.TN

>The advantages of conventional stud construction over a pole barn is that there is framing on which to hang stuff like peg board walls, shelves, etc.

Two people in the club have recently built stand alone shops and they might have advice.

Re: Workshop Building- need help!

#13

Re: where are you moving to?

Chicago Bob

>Bill,

Haven't found a place yet - somewhere between JC & Knoxville. Daughter #1 will be Chem E freshman at UT this fall - looking for something not much more than an hour away from campus so she will maybe come home on weekends.

Looking for a log or cedar type construction with 2 to 10 ac of land, hopefully wooded.

Regards

Bob

Re: Workshop Building- need help!

#14

Re: Workshop Building- need help!

Barry Irby

>Bob, When people post the lay out of their dream shop and ask for criticism the thing most often missing is a place for the project. The tools all have good layout and maybe a logical flow pattern, but there is no place for the thing under construction to be without being in the way. So, my advice is to include that dresser or table, or canoe in the design.

Re: Workshop Building- need help!

#15

Re: You've been in my shop!

Glenn Madsen near San Francisco

>There's room for the tools, and a place to sit, and work at one end of the bench, but no room for the library shelves, treasure boxes, hand tools under construction, the chair with the drying shellac, and the materials for the next project...

I fear it would be much the same if tripled in size.

And my son wants to start another surfboard. And a ukulele.

Re: Workshop Building- need help!

#16

Re: Workshop Building- need help!

Charlie Self

>I built my shop as a pole building, just shy of 15 years ago. What I got: 1200 SF, 9' ceiling (a mistake, go for 10'), insulated, free electric furnace (from a throwaway pile: it lasted about two winters in light use), 200 amp box, plywood floor, PT floor framing, rough SYP wall and roof and ceiling framing. Board and batten mixed rough lumber for siding, built both doors myself, including a double 4' wide set on barn door sliders--another mistake. Interior is 7/16" OSB, which is actually about four bucks a sheet cheaper now than it was then.

My wife and I did the work, except for roof framing and tin installation on roof--I wouldn't use tin again, either. Nostalgia for old VA Piedmont tin roofed farmouses bit me. It's hard as the devil to seal against birds.

Nothing fancy. I forget how many 120 volt 20 amp circits, but I think 7, with two 15 amp lighting circuits. Five 240 volt 30 amp circuits. 120 volt outlets every 4', another mistake. Two feet makes mroe sense, leapfrogging the circuits. I did the leapfrogging.

It cost me about $11,000, not counting the free floor plywood (my wife gave it to me as a Christmas present one year). That would have added a bit over a grand, 3/4" t&g. Nails were just about free as I was testing tools back then and pneumatic nailers fit into the mix.

I bartered for the roof and roof framing work, so there was no cost there.

Problem: ceiling is a bit low. I used rafters, so there's a post every 16' inside (shop is 48' long). Circuitry as described. Lighting is 20 double 4' fluorescents, with a row of incandescents up the center (8 lights) for those cold days when the fluors don't want to work until the joint warms up. Parts of two circuits in eight outdoor 20 amp outlets.

Oh. I set the poles so that the large door is at the proper height for a standard pick up to back right to it. It works great for tool removal and loading...unless you have things like a 750 pound 24" bandsaw, similar fun stuff. That takes help, but back in those days, anything up to about 500 or 550 pounds could be walked off the truck. Not now. I'm too old and fat to move much more than 350 pounds in one package.

Use square posts. Old telephone poles are cheap, sometimes free, but they're a bitch to plumb on two or more sides.

Re: Workshop Building- need help!

#17

Re: where are you moving to?

John K Jordan

>>somewhere between JC & Knoxville

You might also look north of Knoxville - Norris, Andersonville, Lake City, Clinton, etc. Our farm is in Anderson county a few miles north of Clinton and it takes us less thn 45 minutes to get to UT going down I-75. However, I hear property taxes are less in Loudon county to the south west.

JKJ

Re: Workshop Building- need help!

#18

Re: shop pics

Frank Orfanello

>Fred,

What are the dimensions of your building? How tall are the ceilings? How long have you had it? I'm thinking of building one for myself. Thanks.

Re: Workshop Building- need help!

#19

Re: shop pics

Fred Davis

>I put it in the wrong thread by mistake , hope Ellis takes it down.

FredD

Re: Workshop Building- need help!

#20

Re: shop pics

Fred Davis

>Frank ,

read down to the reponse I posted to Bob in Chicago, I got this in the wrong place ;-))

Re: Workshop Building- need help!

#21

moved it for you ;-)

Dan Donaldson

>

Re: Workshop Building- need help!

#22

retirement siding

Bill Tindall, E.TN

>Go brick and not have to spend retirement doing house maintenance. This is the land of mold and rot, the enemy of wood siding. Daffodils are blooming.

Re: Workshop Building- need help!

#23

PS

Bill Tindall, E.TN

>If she is a successful Chem E student she won't have time to come home weekends.

Re: Workshop Building- need help!

#24

Re: moved it for you ;-)

Fred Davis

>Thanks

FredD

Re: Workshop Building- need help!

#25

Re: Workshop Building- need help!

Frank Orfanello

>Thanks Fred. This is what I was looking for. Do you remember what this ended up costing all in when you were done? Just the building and mechanical systems, I have tools and DC. I'm trying to figure out how big the budget has to be to do this right.