Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Lacquer Ventilation

Posts

Lacquer Ventilation

#1

Lacquer Ventilation

Bernard

>I am a weekend warrior building a big bookcase unit (red oak boards and veneered plywood), and I will be assembling and finishing it in my garage (attached). I am looking at using lacquer, since I have not been totally happy with the look of similar projects using polyurethane. It has been recommended to me to use the Deft Clear Wood Brushing Lacquer for ease of use. My question is: are the vapors using lacquer going to be overwhelming if I work in the garage with the door open? Am I better off looking at another finish? Thanks in advance.

Re: Lacquer Ventilation

#2

Re: Lacquer Ventilation

Clint Searl, at the base of Haycock Mtn

>The fumes will definitely soften your brain unless you wear a good mask. Read the can.

Clint

Re: Lacquer Ventilation

#3

Re: Lacquer Ventilation

Howard Acheson

>If you are brushing the lacquer, and have a fan set up, you should be just fine without a mask. Spraying in an enclosed area is something totally different.

Re: Lacquer Ventilation

#4

Option 2

Mark Mandell - Gone Round In Jersey

>Go with an acrylic lacquer like Target USL which can be hand-applied if you don't have an HVLP rig. The Target has very good "burn in" properties (but not quite as good as solvent lacquer), sands and levels beautifully, and rubs out to great depth and clarity. Just don't apply it below 55�. No fumes, water clean-up of tools, and, if spraying, a light mask is sufficient.

Re: Lacquer Ventilation

#5

Re: Lacquer Ventilation

Bernard

>I have a side door as well, but I was going to use the fan instead, as not to stir up too much dust. JUST to be safe, I think I will use a mask anyway; can always use it for other jobs anyway. Thanks for the input.

Re: Lacquer Ventilation

#6

Re: Option 2

Bernard

>I do not have a spray setup, so I was going to hand apply. I have never used this product, but I will DEFINITELY look into it. Thanks. No problem with the 55 degrees, by the way, as I live in Florida. My biggest concern right now is to actually get the job done before the intense humidity (and heat) set in. Thanks for the input.

Re: Lacquer Ventilation

#7

Re: Lacquer Ventilation - Correct about waterborne

Bernard

>By the way, I know that I can eliminate this problem by using the Deft "Waterborne" finish, or similar other products, but I have been hesitant, as I have read several comments that it does not give as good of a finished result, as well as perhaps not prevent yellowing as well. If anybody has any experience (good or bad), that would be appreciated as well.

Re: Lacquer Ventilation

#8

Re: Option 2

Larry in NW Ohio

>You just had to stick us northerners with the "I live in Florida", and you probably was laughing when you were typing it:-)))) As for your finishing project, just have plenty of fresh air and use fans to keep air moving away from you. Good luck with your project. What part of Florida do you live? Larry in Ohio

Re: Lacquer Ventilation

#9

Re: Lacquer Ventilation

Larry in NW Ohio

>Bernard As usual I forgot, If you don`t post pictures you didn`t build it, so we will be waiting for pics. Larry

Re: Lacquer Ventilation

#10

Jesper, Denmark

Re: Lacquer Ventilation

Jesper, Denmark

>Unless you are super sensitive to smell and solvent vapors, this should not be a problem at all.

There are really no flammability issues as long as you can stand being there, but I would not recommend laquering with a cigaret in your mouth.

Re: Lacquer Ventilation

#11

Re: Options *LINK*

Mark Mandell - Gone Round In Jersey

>Check out Jeff Jewitt's site at the link. You can also contact Jeff for expert advice. Don't forget to ask him about the SA-5 additive for hand applications. BTW, confirm with Jeff that you should NOT use foam brushes with the Target; they entrap too much air. The SA-5 is a retarder that allows the film to level better.


HomeStead - Jeff Jewitt

Re: Lacquer Ventilation

#12

Re: Lacquer Ventilation

Fred Davis

>You definitely need to move the air with Deft Brushing Lacquer which by the way is a very good product, but the fumes from it bother me more then typically spraying CAB lacquer .

Also with Deft , you need to practice a little with brushing technique before you get on the project.

Learn to flow the lacquer on with one stroke and resist the temptation go back or over it again. If you missed a place , let it dry and recoat.

If you going over a stain , that really is important to keep from pulling the stain loose.

I am speaking of using Deft's solvent based Nitro-Cellulose version of Lacquer , not water borne.

FredD

Re: Lacquer Ventilation

#13

Re: Lacquer Ventilation - Correct about waterborne

GolfSteve in Calgary

>Hi Bernard.

I've used the Target waterborne lacquer several times and am very happy with it. I use spray equipment for the lacquer, so have not tried hand-application. Every time I've used the Target lacquer, I've also used dyes to colour the wood, so I'm not sure how the un-dyed lacquer might look. I suspect it will look fine.

If you do go the solvent route, you will stink yourself out of the garage, which is ok if (1) you wear a mask while working, (2) you ventilate the garage, and (3) you have a detached garage - you will stink up your house if you have an attached garage.

Good luck,

Steven

Re: Lacquer Ventilation

#14

Since you asked

Mark Mandell - Gone Round In Jersey

>Deft is any form is thin junk posasibly suitable as sanding sealer but useless as a finish [IMHO]. It is low solids, slow build, and merchandised carrier compounds that merely evaporate leaving you with the need to apply a real finish.

[Okay, mebbe not so humble]

Re: Lacquer Ventilation

#15

Re: Lacquer Ventilation - Correct about waterborne

Larry in NW Ohio

>I`m courious, this Target Lacquer, is this a brand name or do you get it from a Target store? Larry in Ohio having a brain fart

Re: Lacquer Ventilation

#16

When The Air Clears, Larry

Mark Mandell - Gone Round In Jersey

>You'll find that the product is MADE by Target Coatings, Inc. right here in Rutherford, NJ.

I'll also venture to say that you'll never find this line of finishes at a "Target" store unless you count the walk-in sales desk at the plant.

No, that's not the plant dept. at Target although I'm reasonably certain there is a Target in Rutherford with a "garden" department selling acrylic or other plastic reproductions.

Re: Lacquer Ventilation

#17

Re: Lacquer Ventilation

Lee Schierer - McKean, PA

>I have used Deft for years and really like it. My only regret is that none of my local stores carry it anymore. It is an excellent finish.

Put on good wet coats with long strokes and avoid trying to smooth it out, particularly after the first coat. I always try to apply it to a horizontal surface as it wil run easily. If the surface is horizontal, you don't get runs and it self levels nicely. It takes longer to finish having to only do the up sides of a project, but the end result is worth it. In warm weather it dries in about an hour. I've used it in an unheated garage at 20 degrees F. It works fine, just takes overnight to dry. You can suspend your brush in a jar of lacquer thinner and avoid trying to clean the brush after every use. Even if the brush dries out it will soften quickly in lacquer thinner.

The best part about Deft is that if a peice gets scratched several years from now, a light sanding and arecoat will bond the new layer of finsih completely to the existing finish. You can't do that with urethane.

Lee