Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Is this a safe operation? Several pics.

Posts

Is this a safe operation? Several pics.

#1

Is this a safe operation? Several pics.

Joe in a Cleveland suburb

>Hi all.

I've always felt if I wasn't comfortable with something on the ts I wouldn't do it. This doesn't feel safe to me.

I need to cut the top off of this little box.

Would you just push it through? I'm affraid I am going to pinch the blade or something.

I've already cut the sides. I'd hate to move the fence.

What do you think?

Thanks for any advice.

Joe

#1



#2



#3



#4



#5


Re: Is this a safe operation? Several pics.

#2

Re: Is this a safe operation? Several pics.

Ed Mulligan, Cape Cod

>Two suggestions:

1.Lower the blade so you leave 1/16" of wood uncut, then finish the cut with a utility knife or handsaw. If the loose top gets jammed between the blade and the fence it might kick back damaging itself and you.

2. Use a follower block slightly narrower than the top to push the box through the cut. Hold it on top as well. This will reduce chances of tipping or twisting.

Okay three suggestions:

Make the cut on a sled instead of the way you have it set up. I'd still cut only partially through and finish the cut by hand.

Ed

Re: Is this a safe operation? Several pics.

#3

Re: Is this a safe operation? Several pics.

Larry in NW Ohio

>I`ve done this a few times, that isn`t saying it was safe, but it needed done. But the only thing different I would do is in pic #4 I would put spacers in your cut length ways. In other words, the way it`shows slip a spacer in about an inch higher than the saw blade and put tape under it so it doesn`t slip down into the blade and tape it on both ends right away so you don`t cut the one end and then have to tape it again. Then run it through fairly easy. Good luck. Larry in Ohio

Re: Is this a safe operation? Several pics.

#4

A.J. Hamler

Re: Is this a safe operation? Several pics.

A.J. Hamler

>Joe...

The way you have it, I wouldn't do it. The way you have the tape on the shim on one side only, the box can be opened like a book. Once you cut all the way through, it would "flap" open as you finish the cut.

It's fine to cut box lids off, but the lid must be secured to the box as if you hadn't already made the first two cuts on the box sides. First, put a shim on BOTH sides in the saw kerfs from your earlier cuts. Then CLAMP the lid in place on the box on both sides.

This way, it's as if you're making your first two cuts again, except on the ends, not the sides. Once you finish both end cuts, your box will still be solidly together until you unclamp the severed lid.

The second way to do this is to make your first two cuts all the way through. Then lower your blade so it doesn't cut all the way through the box ends -- almost, but not quite. When you finish the cuts, it's still a solid box. Now, take a utility knife and cut the top off through the thin sliver you left.

A.J.

Re: Is this a safe operation? Several pics.

#5

Re: Is this a safe operation? Several pics.

Barry Irby

>I agree with the others.

One additional thought. When I do this, I sometimes get chip out where the blade exits the box on the first cut. To avoid that I cut in a short ways on the first corner and then back out. Rotate the box forward and cut so that the nick makes an exit "port" for the blade.

Re: Is this a safe operation? Several pics.

#6

Re: Is this a safe operation? Several pics.

John McGaw

>My feeling is that cutting all the way through without a lot of difficult wedging and fixing is dangerous and likely to ruin the project. There is an easy safe way I've used for years (forget whether I came up with it myself or read about is somewhere). It is as simple as cutting almost all of the way through on two opposite sides and cutting all the way through on the other two. If you leave 1/32" to 1/16" on the "almost" cuts the entire box hangs together and the lid can be separated with a couple of strokes of a handsaw -- or even a craft knife. Any roughness left is easy to remove.

Re: Is this a safe operation? Several pics.

#7

Re: Is this a safe operation? Several pics.

A Wright

>i second AJ's suggestion. An alternative to cutting shims would be to clamp a flat board on the face of each side. The board should be clamped to the box on one end and the lid on the other. The objective is to lock in the current location of the top so it wont move when you make the last two cuts.

Re: Is this a safe operation? Several pics.

#8

that's how I do it.

Bill Tindall, E.TN

>I put the blade to just cut through the thickness of the side. I cut 3 sides and tape them in place, then cut the fourth. But, I use a thin 7 /12 or 8" blade.

Re: Is this a safe operation? Several pics.

#9

Re: Is this a safe operation? Several pics.

Fred Davis

>Joe ,

it dosen't look safe to me either and why it doesn't is because your trapping the small piece (the lid between the fence and the blade.

I have cut many box lids free and I always let the lid fall to the the saw table , not trap it .

The body of the box being much bigger then the lid gives you more control of the cut.

Cutting this way is safe , once you do it , you'll feel beter about it next time.

Your a step ahead of many by asking before you jump how to do a operation you have not tried before.

FredD

Re: Is this a safe operation? Several pics.

#10

Only if you're comfortable with it...

John in NM

>If you've tried it and you're not comfortable, then find another method. I've done what's pictured before, I don't recall being any more bothered by it than say pre-trimming fielded panels. Doesn't give me the creeps anywhere near as much as a plunge cut for a stopped groove (but then my saw is an old one and runs at 1725 rpm).

Why not cut the ends first, then the sides? Long side last is a little easier to deal with. I also like John's suggestion above, dropping the blade a little on the last two cuts, as then you don't need to shim.

Re: Is this a safe operation? Several pics.

#11

Got it to work. Thanks for the tips!

Joe in a Cleveland Suburb

>