Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

plywood veneers are soooo thin!!!!!

Posts

plywood veneers are soooo thin!!!!!

#1

plywood veneers are soooo thin!!!!!

lee beeden

>I have almost finished a run of plywood table tops made out of red oak and then capped with 2" x 7/8" solid Oak trim.

I used biscuits to attach the solid stock.

To cut a long story short, during clean-up i have sanded through the veneer exposing a white wood of some sorts in a few places, it looks terrible.

Also there are a few gaps between the solid stock and the ply.

What do you use for filler, that will match an oil finish?

And can the veneer be colored?

Any comments appreciated.

Lee

Re: plywood veneers are soooo thin!!!!!

#2

Re: plywood veneers are soooo thin!!!!!

A Wright

>The best fix is to take some of your leftover plywood and slice a veneer on the table saw, then inlay it into the area you sanded through. One good thing about oak is that the grain is coarse enough that it is relatively forgiving if you have to do this type of repair (at least compared to a tight grain wood like maple)

Re: plywood veneers are soooo thin!!!!!

#3

Re: plywood veneers are soooo thin!!!!!

Dick Coers

>Ain't nothing going to look "good" with a repair. Any patch will require crosscutting of the veneer someplace. Irregular lines will disguise it a little, but something is going to show. A cabinet scraper is the tool of chose to bring the border material and the plywood sufaces together. I always make the border proud, and bring that to the plywood. I some instances I have kept a sheet of paper between the veneer and the scraper as I work down the solid, just in case. Then it is easy going with hand block sanding to bring them flush.

Famowood is my favorite filler. It comes in several tints, either solvent or water based, and works great. It won't accept stain, but being tinted usually in enough to make it work. You have to be careful with fillers and oak, as you can get filler in the pores and change the look around the fill. I have masked off the crack before and that keeps the filler only in the gap.

Re: plywood veneers are soooo thin!!!!!

#4

Re: plywood veneers are soooo thin!!!!!

Jay St. Peter - Southern, MD

>I agree with both posts above. An inlay will work, but you'll have to go full length of the table to avoid obvious seams. I'd rout light groove right along the edge and as wide as necessary to cover the damage and fill with veneer. It'll get rid of the gaps and fill the damage. It's a lesson we've all learned the hard way.

Jay

Re: plywood veneers are soooo thin!!!!!

#5

Ellis Walentine

Grain paint it

Ellis Walentine

>In the contract furniture industry, where time is money, and elsewhere, grain painting is the preferred method of covering up sand-throughs. The trouble in your situation is the oil finish. Grain painting only makes sense if you're going to top coat it with a sturdy film finish. You decide, but I'd go the grain paint route (which is another discussion entirely) and then hit it with lacquer.

Tough one. In the future, be sure to make the edgebanding proud and ease it flush as someone already mentioned.

Ellis

Re: plywood veneers are soooo thin!!!!!

#6

Re: Grain paint it

Larry in NW Ohio

>Don`t forget to complain to the place that you bought it from. That`s what I did a couple of years ago with some junk oak plywood after I used it and I got my money back. I bought it from Menard`s. Larry in Ohio

Re: plywood veneers are soooo thin!!!!!

#7

Re: plywood veneers are soooo thin!!!!!

Jerry Samsen

>I've done that. Just resigned myself to rebuilding the top and learned my lesson.