Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

0 Clearance Insert

Posts

0 Clearance Insert

#1

0 Clearance Insert

Dustmaker Mike

>OK I want to make a few inserts for my TS. I do not understand the $20+ price for them. I have some corain that is the right size and was wondering if it would rub the blade and dull it? If so what material works better that does not require a lot of milling to form.

Thanks

Re: 0 Clearance Insert

#2

Jim DeLaney, Austintown, Ohio

Re: 0 Clearance Insert

Jim DeLaney, Austintown, Ohio

>I've been using corian inserts in mine for quite a while - no problems.

One caveat,though - if you drop it on a concrete floor, it will break just like glass.

Jim D.

Re: 0 Clearance Insert

#3

Re: 0 Clearance Insert

john lucas

>I use high grade plywood and put formica on both sides. After cutting the opening for the blade I simply use a metal file and enlarge the opening by a few thousandths. It just takes a few swipes on each side.

Re: 0 Clearance Insert

#4

Re: 0 Clearance Insert

Jim Dillon

>Mike,

While I have never used corian, I don't see why it wouldn't work. I've used 1/2 inch birch plywood, along with a flush trim router bit to fashion mine. I use double-sided tape to fasten the stock metal one to the plywood - that has been trimmed to near size on the bandsaw. Then carefully adjust the router bit height in my router table and have at it. Minor sanding adjustments are then made to give a tight fit into the opening. I insert a nail into the outfeed side of the insert that fits under the table top so the insert is less likely to lift up. I also had to place a few pieces of masking tape under the insert to bring it to the correct height.

Jim

Re: 0 Clearance Insert

#5

Re: 0 Clearance Insert

Don Orr

>I did very much like Jim last weekend. I had some scrap 1/2" birch veneer plywood (not BB, just from a borg), traced my regular ZCI onto it, roughed it out on the bandsaw, and flush trimmed it with a bearing guided bit in a hand held router using the ZCI as a pattern. Fit perfect first try. I even remembered to drill a finger hole so I could get it out of the tablesaw. I was making mine for a dado blade. I think if you did as John said and clean up the slot with a file, the corian should work great. If you are using it for a standard 10" blade, it will not sit all the way down in the opening without hitting the blade. You will need to remove some material on the underside of the ZCI before it will sit all the way in the opening so you can raise the blade to cut the slot.

Re: 0 Clearance Insert

#6

Re: 0 Clearance Insert

Lee Schierer - McKean, PA

>Years ago, I discovered that luan underlayment plywood is the perfect thickness for inserts for my craftsman table saw. I could make dozens of inserts from scrap luan. I also noted that they would flex slighly if I pressed down on them after they had been slit by the saw so on the right side of the blade, I normally glue a piece of 1/2 x 3/4 scrap along the underside (long dimension vertical) as a stiffener. I used these for years and still do for zero clearance dado inserts, until I was able to get an aluminum insert made with a dovetail wood insert like Norm has on his saw. A machinist friend made it for me in exchange for some woodworking.

Lee

Re: 0 Clearance Insert

#7

use set screws to level

Bill Tindall, E.TN

>I drill and tap the corners for 10/24 set screws that align with the underneath table saw "shelf". These are adjusted to get the insert level. Actually you don't even need to tap plywood or real wood.

I have made many. I have used with equal success- a piece of maple, plywood, aluminum plate, 1/2" plastics of several varieties (acrylic, HDPE, nylon).

The bottom line is that about anything works. I like the pattern router idea for fitting.

Re: 0 Clearance Insert

#8

Re: 0 Clearance Insert

Yonak

>What's the problem with raising the saw blade up through it while holding the insert in place ?

Re: 0 Clearance Insert

#9

Re: 0 Clearance Insert

Jim Dillon

>Yonak,

I place the table saw fence over the insert when cutting the slot being careful to not cut into the fence. Regarding the nail, I was trying to sorta duplicate the metal protrusion on my original metal insert. Seems to work OK, at least I haven't had one fly off yet and sure hope I don't. Hope this answers your question.

Jim

Re: 0 Clearance Insert

#10

Re: 0 Clearance Insert

Larry in NW Ohio

>Mike I get my material from US Plastics in Lima. I can`t tell you exactly what it is but it`s white and it seems to work well. If you go to the Columbus show and want to come around this way and pick some up, I`ll get some for you. Or if you want to go with us on Sunday your more than welcome, I could have it ready for you. Just let me know. Larry in Ohio

Re: 0 Clearance Insert

#11

Sounds Good to me

Dustmaker Mike

>Check E-mail.

Re: 0 Clearance Insert

#12

Jim DeLaney, Austintown, Ohio

Re: 0 Clearance Insert - Plastic Cutting Board

Jim DeLaney, Austintown, Ohio

>Those half inch thick plastic cutting boards they sell in restaurant supply houses make goo stock for ZCIs. A ten dollar board will make about six ZCIs. That's what I'm using right now for my dado inserts.

Jim D.

Re: 0 Clearance Insert

#13

Quite A Lot Of Milling To Form

George@Colonel's Workshop-Havertown PA

>Hello Mike,

Some of the saws require more milling than others. My new Jet Hybrid is a real pain to make ZCI's for, so I am fairly limited in choices of materials. I chose solid wood, and currently am using white oak and a couple on maple. I can thickness these to gross thickness and further machine with forstner bits, those areas which sit upon insert rests cast into the iron table. The steel insert which came with the saw is very thin, but has integral stiffeners. I do not dislike the saw's lousey insert design enough to become unduly emotional, but its a bad job on a good saw. Solid wood is the only way I can go, other than rewarding somebody for Jet's bad design by buying an after market ZCI.

George

Re: 0 Clearance Insert

#14

Re: Quite A Lot Of Milling To Form

Larry in NW Ohio

>Colonel How thin is it at the ZCI rests, I may be able to find something to fit, if you wish to try something else. Larry

Re: 0 Clearance Insert

#15

Re: 0 Clearance Insert

Barry Irby

>I made a bunch of them out of half inch borg plywood. Pattern routed them as others have suggested. When I realized the ten inch blade on my saw would not retract far enough, I solved that problem by installing one of the eight inch blades from my dado set and "under cutting" them. Just put the smaller blade on and raised it almost through all of them. Did not allow it to penetrate the top so that the actual blade wound cut its own slot, hence "zero clearance". While I was at it I pre cut a few for various widths of dadoes, but that may have been a waste. You don't really know how long you want that dado slot until you use the plate and one with a slot way too long looks pretty scary.