Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Moisture

Posts

Moisture

#1

Moisture

Tim Fulton

>The recent rapid changes in temperature over the past few weeks here in Tennessee has resulted in rust forming on all of my tool beds. In addition, all of the windows and doors where simply dripping with water. Unfortunately, I've spent the past two days removing the rust..!##@#$ My question is... outside of installing a central heat system I've waxed the tool beds pretty good. Will that be enough to prevent rust or should I purchase some form of tool cover? What tool covers have you used and what do you recommend?

Thanks in advance...

Re: Moisture

#2

Re: Moisture

Dave Paine

>If the windows were dripping with water, it is likely that you had water condensation on the tool beds. This will be difficult to prevent becoming rust.

Wax, Slippit, Boeshield, etc. are all good for a moisture barrier for water VAPOUR, but I expect they would all allow some water condensation to react with the cast iron. Sometimes my own perspiration from a hand print can cause rust. I know when my nephew placed his soda can on a tool, it resulted in water ring condensation and some light rusting. Caught this before it was too bad.

If you are having condensation, I would expect any cover, even a tarp would greatly assist in having the condensation mostly on the cover and not the tool. You could also try cutting polystyrene foam to cover the beds. This would provide a degree of insulation.

Good luck. I appreciate the frustration of having to spend the time removing rust. Feels to be never ending.

Re: Moisture

#3

Re: Moisture

Fred Davis

>Heat is the obvious answer , but a dehumidifier would work also , and less costly to run.

FredD

Re: Moisture

#4

Re: Moisture

David

>I just ran a post similar to this on the OWWM website. Up here where the winters run a tad cold (-2 to 15F today) condensation on tools in an unheated shop is an issue. By the time I get my shop warm water is dripping off the cutter heads on my jointers, chisels are dew covered, ice crystals form on some of the outside walls, but I digress. The recommendations I received were either insulate, heat, or cover my tools. People recommended 1/4" plywood. I was also thinking about the magnetic ones available from various suppliers. Also thinking about drop cloths that have one waterproof face and on soft face. Other than that, it's wax, wax, wax.

Re: Moisture

#5

Re: Moisture

Tim Fulton

>Wax on - Wax off, wax on - wax off... is what I have been doing for the past few days after removing the rust. The shop is pretty well insided... once the shop warms up, it will stay that way for about 24 24-36 hrs and stay comfortable. I'm looking at gas heat but with funds tight we'll wait and see.

Thanks for the responses... Wax on-Wax off

Re: Moisture

#6

Re: Moisture

John E in SC

>You absolutely need to address this issue, or you'll have more problems that just rust on your tools - water dripping off your windows and doors is trouble waiting to happen (mold, rot, etc. etc.) At the very least you should try a dehumidifier (but if it's that cold, I would doubt it will work well without some type of heat source.) It's not that cold here, but I have an oil-filled, electric radiator heater that with a thermostat that I occasionally use to keep temps from getting too cold. Was only $40 or so if I recall, and shouldn't be much of a fire hazard if left unattended - might want to consider something like that in addition to the dehumidifier. Covers may protect your tools, but not your house.

Re: Moisture

#7

Re: Moisture

Steve Schoene

>There are low temperature dehumidifiers, (not below freezing, etc, I don't think) but I only looked very briefly at them, when I saw prices. It's not like your basic Sears dehumidifier.

Re: Moisture

#8

Re: Moisture

Pete LaBelle

>If the tools are not in service, use WD40. Water Displacment, trial #40 (where it gets its name from) is designed to displace any water. I spray the bed of my surface planer (gets used a couple times a year) with a generous coat of the stuff. Keeps it rust free during the winter and suprise thaws & foggy weater.

Re: Moisture

#9

What's your heat source?

Lee Schierer - McKean, PA

>Torpedo heaters, radiant gas burners, Kerosene heaters of all types and any other non-vented type heater with a flame will produce water vapor when they burn. The air in your shop will hold this moisture and it will condense on any cold surface, e.g. the windows and your tools.. You need to eliminate the water source or get used to rust removal. Switch to electric heat or a vented system.

Where I used to work we made million dollar machines with cast iron frames. We tried all sorts of materials to coat cast iron machines for shipping that was easy to remove, including paste wax. Our best success came from Boeshield T-9. It was far superior to WD-40 or any other spray on oil we found and we tried a lot of products. For tools that are used infrequently spray on a heavy wet coat and leave it. When you need to use the tool spray on another coating and wipe it off. for tools being used all the time spray on a coating and wipe it off.