Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Rikon adjustment (long)

Posts

Rikon adjustment (long)

#1

Rikon adjustment (long)

Guy

>Hello all, I have a Rikon 18 inch bandsaw and have had it for a few years. Haven't had any problems with it until this weekend. I tried to do some resawing but as soon as I put the wood to the blade it curves in towards the left (inside edge). Not just a little but enough to be unusable. I checked my guides, tension, etc and all seems well. I tried a new 1/2 inch blade, same thing. Finally I put on a 1 inch blade and have the blade tensioned as much as it can. Now it works OK. I did try different woods also with the same result. Any suggestions? I normally keep the 1/2 incher on there to trim blanks for turning on my lathe and my wife wants some bandsaw boxes so I plan on using a 1/4 incher also. It has always worked fine so far and I am stumped. Any suggestions, etc would be greatly appreciated. Thanks, Guy

Re: Rikon adjustment (long)

#2

Fence adjusted for blade drift?

Alexander Grigoriev

>

Re: Rikon adjustment (long)

#3

Re: Fence adjusted for blade drift?

Guy

>It was (still is if I use the 1 inch blade). This thing literally dives as soon as the wood hits the blade and within 2 to 3 inches the blade twists bad enough that it is screeching and the piece of wood has to be turned past 60 degrees from origination point but by then I am pulling out before I snap a blade. Yes bottom guides are checked too. I am getting ready to go to the shop and recheck/adjust all from scratch again. :(

Re: Rikon adjustment (long)

#4

Re: Fence adjusted for blade drift?

Alexander Grigoriev

>Drift is different for different blades, and even could change depending on the guide position

Re: Rikon adjustment (long)

#5

Re: Fence adjusted for blade drift?

Thomas S Stockton

>Guy,

I would start over back the guides out and double check your blade tension, then turn the saw on and let it run for a minute, stop the saw and adjust the guides. Then check for drift and set your fence. You should be good to go.

Some things to look for from personal experience.

Is the blade really sharp or did you accidentally grab an old one.

Did guides set wrong dull the blade, this will happen if the front of the teeth touch the side bearings and it only takes a minute to ruin a blade.

What kinda wood are you cutting I had some elm that would destroy a regular steel blade in about 6" bi metal blades solved that problem. I've also had this problem with rosewoods and narra.

Search the archives for info on how to set drift in my experience when drift is set wrong it usually appears a ways into the cut not at the beginning. almost all of my cutting problems have come from dull blades.

Tom

Re: Rikon adjustment (long)

#6

Re: Rikon adjustment (long)

John K Jordan

>Guy,

When you say "it curves in" do you mean the cut bows, i.e., curves vertically?

Bowing can be caused by a dull blade, but most often by insufficient tension. The tension gauges on bandsaws are notoriously worthless. Using a very aggressive blade that was a tiny bit too long, the gauge on the 18" Rikon measures distance - told me the blade was tensioned perfectly even when it was still too loose to use! Worthless.

What works: a few years ago I bought a Starrett tension gauge to use with my bandsaws and to check my Woodmizer sawmill. This works like a charm and is always right. The Starrett is a bit pricy but Iturra Design has had one made based on the Starrett design and sells it for significantly less. They don't have a web site but you can call: 866-883-8064. If you haven't dealt with them, ask for their excellent catalog.

I could never get my 14" Delta tensioned properly with the larger blades so I limited it to 1/2" blades. The 18" Rikon works great even with thick blades 1" and wider. I cut a lot of thick green wood with 1.5 TPI blades.

BTW, something to watch out for with green wood - gummy buildup on the side of the blade. This will increase the friction and cause all kinds of problems.

JKJ

Re: Rikon adjustment (long)

#7

Re: Fence adjusted for blade drift?

Robin Corell in Atascadero CA

>What Tom said, plus you might do a quick check to make sure the blade is roughly centered on the tire as opposed to riding at the back or front edge.

Robin

Re: Rikon adjustment (long)

#8

Re: Rikon adjustment (long)

Guy

>I rechecked everything last night and found a couple of the bearing guides had gone bad. But it looks like once I get the new bearings I am going to tear this beast down and double check the whole thing. I have it tensioned as far as it can (disregarding the tension "guide"). It curves in as soon as it touches wood, doesn't matter whether I use pine, oak, walnut, 10 inches thick or 3. The new blade is definitely a new, virgin blade. Thanks for all the suggestions. Will definitely double check everything and post a follow-up. Again, thanks !!

Re: Rikon adjustment (long)

#9

Re: Rikon adjustment (long)

Dan Donaldson

>You say it is as tight as it can get and yet curves as soon as it touches wood. How much deflection does it have when pushed with a finger in the center? Sounds like it might possibly be a weak tensioning spring. Something to look at anyway.

Re: Rikon adjustment (long)

#10

Re: Rikon adjustment (long)

John K Jordan

>>Sounds like it might possibly be a weak tensioning spring.

My thought too, or just not cranked enough. I checked a new 1"x.035" 3/4TPI (Starrett) bimetal blade today with my tension meter and with the gauge pointing all the way to the maximum it still did not reach 10k psi when it should have been at least 15K psi. The wider and thicker the blade, of course, the more force needed to tension properly. I'm going to tension properly and try recalibrating the gauge.

JKJ