Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

OT DVD/CD Disc Repair ????

Posts

OT DVD/CD Disc Repair ????

#1

OT DVD/CD Disc Repair ????

Andy Lincoln,in Dearborn,MI

>Hi All,

Thought I would ask here before turning to the rest of the internet for help. I would like to know if the DIY disc repair gadgets that are available are worth the $30~40 or so I've seen them for?My son has video game systems that are on disc an even when he is careful the discs end up scratched somewhat and alot of the games he gets are used from Gamestop and some have scratches when we get them.I also use Netflix for movies and occasionally get a disc that is scratched to the point it cannot be played.Netflix will send out a new movie if damage is reported but if I could fix a disc in short order it would be ultimately more convienent.

Thanks,

Andy

Re: OT DVD/CD Disc Repair ????

#2

Re: OT DVD/CD Disc Repair ????

Bob Henderson

>For what it is worth...

I've used one called SkipDr. Sometimes it works and sometimes it doesn't. It paid for itself when it saved a CD I'd special ordered from the UK. The principle is simple. 1. it cleans the crud off the disk; 2. it fills in the scratches with some sort of clear acrylic and polishes the surface.

I've always wondered if I could achieve the same result with some Future brand acrylic floor wax and a soft cloth, but have never risked the experiment.

Re: OT DVD/CD Disc Repair ????

#3

Wax on Wax Off

Dustmaker Mike

>I use pledge to clean them. Most of the time scratches don't hurt the factory made disk. What hurts them is the top being scratched so the laser don't reflect.

So now there are few types of disk:

Read only They are the best to get. The information is burnt into the plastic.

Read Write one time the next best

Read and rewrite. This is the worse kind to count on. They use a chemical reaction to change the information on the disk. The information is sort of shades of black and gray. Heat will kill these fast.

CD or DVDs will last up to five years. Most of the time these will go bad in a year if stored in a car. The heat causes the shades of gray and black to fade which cause the information to be lost.

Anyway use some pledge or other spray wax to clean and buff them and they should last.

Re: OT DVD/CD Disc Repair ????

#4

Re: OT DVD/CD Disc Repair ???? *LINK*

Dan Mitchell

>I have hundreds of music cd's I ripped/burned over the years from disks borrowed at the local library. As you can imagine, some of these disks were in awful/unplayable condition when I checked them out. I never found one that could not be made playable after a polishing with "Brasso", a fine abrasive liquid made for polishing brass, etc. No gadget required, simply pour a bit of Brasso on a paper towel & buff away. Here's a link about using the product on such disks.

Dan


http://www.instructables.com/id/Re-surfacing-CDs-s

Re: OT DVD/CD Disc Repair ????

#5

Re: OT DVD/CD Disc Repair ????

John K Jordan

>Remember to only polish the bottom. The top is a very thin layer of lacquer over the data layer, a thin foil in commercial disks and a dye for writable disks. If the data layer gets scratched, nothing will fix it.

The laser focuses through the bottom layer of plastic which makes up most of the thickness of the disk. Focusing through this layer thickness causes small scratches on the surface to appear out of focus so they don't interfere with the data. Heavy scratches can be polished away. I've used various fine polishing compounds successfully. The best was a kit from Micromesh used to restore scratched aircraft windows to sparkling clear. I've never tried Brasso on CDs but it is a pretty fine abrasive and should work.

JKJ

Re: OT DVD/CD Disc Repair ????

#6

What I have done...

Grant in Iowa

>First, let me preface this with a warning: Try the less invasive solutions first such as cleaning and the "disc washer" solutions.

Here's my method that has worked dozens of times.

-A spiral sewn buffing wheel at medium speed (maybe 1200 RPM or so...)

-buffing compund suitable for plastic (available at Sears). I use white, the going is slow, but mistakes are also slower...

-Arbor for the buffing wheel to adapt it to your drill press... allows speed control to achieve 800 to 1200 RPM.

1. Install the buffing wheel on the arbor and then into the DP chuck. Set the DP speed to between 800 and 1200 RPM (I use 1200).

2. Turn on the DP and "load the wheel" with rouge. If you aren't familiar with using a buffing wheel, try buffing something indestructable and cheap first, such as a craftsman screwdriver handle. Also practice on a non-critical CD, before you graduate to the subject CD.

-Notes: ALWAYS buff on the side of the wheel spinning away from you, so that the object being buffed cant be thrown towards you if it catches. Any of the objects edges can "catch" the spinning wheel, and be thrown. Also, this is one operation where leather gloves would be a good idea.

3. Now that you are all practiced up, add rouge to you wheel again and hold the CD in your gloved palm so the bottom surface is up, and the part you want to buff is away from you. introduce it to the wheel such that the wheel begins contacting it just outside of the center (BUT not catching the center hole!), and leaving the CD near its edge. Use a light touch and stop to clean the rouge off with water to inspect your work. You'll notice the buffing wheels contact patch has a sweet spot that yields the best action. Pay attention to this and use it to your advantage.

-Most CD's have a layer of plastic that is thick enough so you can even sand with 800-1200 grit paper to remove deeper scratches, then buff out the sanding marks.

I have saved about 80% of the discs I have tried to fix using this technique. Honestly, I have not tried reading up more on plastic polishing, but that might be the best approach for anyone wanting to have the best possible chance of success.

Hope this helps!

Grant in Iowa <---recently saved a WindowsXP disc I needed to reinstall.

Re: OT DVD/CD Disc Repair ????

#7

Re: OT DVD/CD Disc Repair ????

Bob Entwisle in NJ

>I've had good results on used music CDs that I buy to rip, by applying plain old automotive 'cleaner wax' to them and then polishing them up. This method has allowed me to rip the cd to the hard drive after which I probably will never touch the CD again. The current wax in the house is Mothers California Gold. I've never had need to try it on DVD's so don't know if it'll work for them, but if you can read it the way it is, you've pretty much nothing to lose by trying. My theory is that there are scratches on the CD that redirect the light at an off angle so the read head doesn't see it, by polishing the scrathes out, you remove the scratches and the light reflects where it's readable.

Bob

Re: OT DVD/CD Disc Repair ????

#8

Re: OOPs.....OT DVD/CD Disc Repair ????

Bob Entwisle in NJ

>Meant to say "if you CAN'T read it the way it is"........

Re: OT DVD/CD Disc Repair ????

#9

Re: OT DVD/CD Disc Repair ????

Larry in NW Ohio

>When everyone says to "buff it" do you mean to buff across or around the disk, or just plain makes no difference. Thank You Larry in Ohio

Re: OT DVD/CD Disc Repair ????

#10

Across

Bill Howatt

>Always buff, wipe or whatever a CD/DVD across the disk from center out to circumference. Never wipe/buff in a circular motion - a mark like that causes even more problems in reading than one out from the center. It makes sense if you think about it. A short blip from a line from the center could likely get corrected by the error-correcting code (ECC), a long blip from a circular line could cause a much larger data loss that the ECC can't handle.

Bill

Re: OT DVD/CD Disc Repair ????

#11

Re: OT DVD/CD Disc Repair ???? *LINK*

Andy Lincoln,in Dearborn,MI

>Thanks to all who replied.Last night I tried the Brasso method and my 11 year old son would like to report that it works just fine now.The best part was that I had a can of Brasso in the shop and we didn't have to leave the house to remedy the disc problem,nor pull any more $$ out of my pocket.That's about $30 towards my next tool,which may or may not be Andrew Lunn's Backsaw that appeared a couple days ago on the Hand Tools board.

Thanks All and Happy Holidays,

Andy


Andrew Lunn's saw on Hand Tools

Re: OT DVD/CD Disc Repair ????

#12

Re: OT DVD/CD Disc Repair ????

Dan Mitchell

>Glad the Brasso worked out for you, as I said, I've never known it to fail ;-)

If this is especially an issue with your son's video game disks, it might make sense to make a backup copy when you 1st get the new disk. I'm not personally familiar with such games, but I'd be surprised if there isn't a way to copy them on the PC. Your son could even use the copy & you could keep the original for any future replacement needs.

Dan