Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Basements and DryLok question

Posts

Basements and DryLok question

#1

Basements and DryLok question

wilbur

>A couple of years ago I painted my basement (cinder block walls) with DryLok, which worked great for reducing the humidity in my shop area.

Now I want to attach some 2x material to the basement walls to hang some shelves and storage on. I'm planning to use Tapcons or lead anchors for this. Either method will involve drilling through the areas that I painted over with DryLok.

I'm a little worried about moisture entry through the holes that will be drilled, and that moisture getting to the 2x material.

Am I asking for trouble? Or am I overthinking this?

Re: Basements and DryLok question

#2

JL

Re: Basements and DryLok question

JL

>With Tapcons you are plugging the holes. With lead anchors and bolts, you are plugging the holes. So what's the problem?

If you are really worried, put some caulk in the holes before you put in the lead anchors.

Re: Basements and DryLok question

#3

Re: Basements and DryLok question

Larry in NW Ohio

>Wilbur I think what I would do, if you can, is to put a plate,2x4, at the bottom and at the top fasten the 2x to the joise or put a plate at the top to screw to. Merry Christmas Larry In Ohio

Re: Basements and DryLok question

#4

Re: Basements and DryLok question

Justin Szeliga

>You could also bed the 2x in caulk to keep the seal together.

Peace

Justin

Re: Basements and DryLok question

#5

Re: Basements and DryLok question

Barry Irby

>My real job is Home Inspector. (A private one generally for people buying houses, Not a county or state Building Code Inspector, but there are a couple of those guys here too and maybe they will jump in.)

If the wall did not appear wet and you just coated it with Drylok to reduce the humidity, I don't think driving anchors into it will have much effect. OTOH, the lumber you attach to the wall should be pressure treated. If the wall is truly dry, regular lumber will last a long time, but if it is wetter than you think, it may rot over time and it is attractive to termites and other wood destroying organisms. Use PT lumber and the appropriate fasteners to go with it. (The fasteners should say right on the boxes suitable for ACQ and if the lumber is not ACQ treated be sure to read up on the requirements for that type.)

Re: Basements and DryLok question

#6

Re: Basement Wall - Agree w/ Barry & Larry

Ray Carson - Lawrenceville, NJ

>Why anchor to the wall if you don't have to? And if you leave enough of a gap you can run electrical wiring behind the studs. :-)

As a "structural guy" I would place a sill off the basement floor with spacers. Everything anchored into the slab. Then a plate at the top of the wall. You don't necessarily have to lay it across the bottom of the floor joists. You could always anchor every other stud to the floor joists to brace the wall. With careful layout of course. I would also use PT wood. All this provides another benefit, if the time comes to sell the house, nothing is anchored into the block should it need to come down.

I built my kids playroom walls this way and it saved a lot of time because I didn't have to drill and so forth.

Also, having recently become a Licensed NJ Bldg. Inspector, the wall may not be considered a "permanent addition" requiring permits, etc. And, if your house is ever re-accessed for value, anything fixed to the walls could easily be taken down to avoid the possibility of raising your taxes. You just ask the accessor for a time extension and in that time you take it all down. I checked with my local town codes before I built walls for the playroom and had I "anchored" the walls to the block I would have needed a permit. And it was considered a finished basement. ???? How bout that for busting your chops.

So, use PT wood, and don't anchor if you don't have to. My 50 cents worth, (inflation)

Merry Christmas!

Ray

Re: Basements and DryLok question

#7

Re: Basement Wall - Agree w/ Barry & Larry

Fred Davis

>Ray's approach wil work quite well , but you are still using fastners for the blocks under the sill , rather then do that I would bond the blocks to the slab with PL 500 , let it cure overnite and then nail down the sill to the blocks.

FredD

Re: Basements and DryLok question

#8

Re: Basement Wall - Agree w/ Barry & Larry

wilbur

>Hi Ray,

Thanks for the info -- I live in NJ too.

Anchoring to the floor joists above is difficult because of the way that wiring and plumbing run across the ceiling of my workshop, and because I want to maintain access to them. But if I could figure out a way to anchor to the joists above, wouldn't I also have to anchor the floor plate to the floor of the basement as well, in which case I'd have the same inspection issues you mention as if I had anchored my 2x material to the walls in the first place? Or would I just be relying on gravity to hold the floor plate in place?