Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Shower Door Wood Selection?

Posts

Shower Door Wood Selection?

#1

Shower Door Wood Selection?

Thomas Skaggs, Foothills of Mount Level

>Wooden shower doors you ask? Well only the frames. It's a long story...trust me. The basic facts are that I have some awesome Art Deco etched glass panels that I want to make into shower doors. The problem is they are not tempered glass. (not code). Therefore the local shower door folks can't do the project for me.

So I will be making the doors myself. For safety I will be adding tempered glass panels on the inside of each door. So basically door frames with 2 glass panels. The glass panels will actually be silicone set in anodized alumninum channels and the channels will then be silicone set in dadoes in the door frames.

So I am thinking of Teak for the door frames. But I am open to other wood suggestions? I am between painting the frames with an epoxy paint or a marine finish. The doors will not get direct water sray on them but need to be moisture resistant.

Wood selection suggestions welcomed.

Thanks

Tom

Re: Shower Door Wood Selection?

#2

Re: Shower Door Wood Selection?

NickB in Eastern Mass.

>If you're going to paint, why not just use a good rot-resistant wood (cypress and white oak spring to mind) - cheaper, easier on your tools, and no worries about the oil in the wood degrading your adhesive performance.

If you're going to clear coat, I'd go with relatively rot resistant (white oak, mahogany, etc. - depends on what look you're after).

Personally, I've never put a finish on teak (it doesn't need it, and I'm not up for the maintenance of renewing an oil finish - my deck furniture is all silvery. My dad built a sailboat when I was a kid - we just scrubbed the teak with some seawater and a nylon brush to take off the dirt and bring back the color).

If you want to go without a finish, ipe also springs to mind (but man, is it heavy).

Hope this helps,

Nick

Re: Shower Door Wood Selection?

#3

Re: Shower Door Wood Selection?

Jim Shaver - Oakville, Ont

>Cool detail Tommy,

I have a like for white oak or teak if you want the wood to show, nevertheless they will in time need some maintenance.

I am almost done my remodels as well, seamless glass rocks ....Wonder if you can see the price vs quality thing, it was not bad, I also saw some framed glass panels at a supplier in Oakville, it was spectacular.

Take care,

Jim

Re: Shower Door Wood Selection?

#4

Re: Shower Door Wood Selection?

Clint Searl, at the base of Haycock Mtn

>Tom, one of the nicest rot resistant woods to work with is cypress; easy to mill and surface, especially if quarter or rift sawn, and it'll take any finish. And the finish I would use is Behr one part water based epoxy. It's marketed as garage floor paint, but I've used it in clear and tinted white on indoor and outdoor wood as well as an old fiberglass shower floor pan and on raw travertine bathroom tile. I'ts easy to apply and tough.

Clint

Re: Shower Door Wood Selection?

#5

purple heart, wenge, claro...

Robin Corell in Atascadero CA

>If the doors are inside and encapsulated in epoxy you could just about use any wood you want, even pine. I am guessing you will still prefer a strong hard rot resistant wood. One that springs to mind and is often over looked is purple heart. It is nearly as rot resistant as teak and has a long tradition of being used in boat building.

If you are going for a deco look you may want to choose your wood for the color. Claro walnut would not be a bad choice for a dark wood but wenge would also be a good choice. I once saw some deco styled chairs made out of flat sawn wenge that were soaked in a two part bleach to turn the brown parts white but leave the black parts black, a really wild zebra look.

Several have mentioned cypress. In CA we have monterey cypress and it is a closed porous wood. A bit soft but it would work. It has a nice warm orange tone to it as it ages. Evan Shively over in Marshal has some. Our cypress is extremely stable dimensionally once it is dry and milled to size. Because it grows on the windy coast it can have some internal stress and spring off the blade a bit when cutting but from then on it is nearly as stable as claro walnut.

With two sheets of glass you have created a greet opportunity for LED light in between the sheets. EL sheet would also be awesome.

Robin

Re: Shower Door Wood Selection?

#6

Alan Young

We expect a plethora of detailed shots

Alan Young

>when this project is completed. Sans occupants of course!

Alan

Re: Shower Door Wood Selection?

#7

Always Expect the Unexpected, Allan :

George@Colonel's Workshop-Havertown PA

>

Re: Shower Door Wood Selection?

#8

The Colonel.....

Thomas Skaggs, Foothills of Mount Level

>....knows me all to well. ;-)

T.