Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

So what does Norm really use?

Posts

So what does Norm really use?

#1

So what does Norm really use?

Glenn Madsen

>To fill all those holes he makes with the brad nailer, while the glue dries?

I built LOML a set of shelves for her ever increasing quilt stash. Plywood, maple domestic, and prefinished. And the face frames got trimmed out with (free to me) cherry that a buddy dropped off six weeks ago (a gloat, I guess). But we're in a time crunch, holidays and family and all, and I brad nailed the trim on, 18 and 16 ga, depending on the gauge, intending to fill the holes with some of the Rockler Wonderfil putty on the shelf.

It is the aproximate consistency of clay. Maybe somewhat harder. Anyone ever succeeded in reconstituting this stuff for filler use?

The DAP oil-based filler right next to it on the shelf is about the same consistency. Flowing into a nail hole doesn't seem to be on its agenda. Can this be recovered?

Or is there an easier way that doesn't rely on sawdust and shellac?

Worst case, I guess they could be ignored...

I'm into this project about $200 now, which is about $300 more than I had budgeted this month.

Re: So what does Norm really use?

#2

Re: So what does Norm really use?

Robin Corell in Atascadero CA

>The dap stuff should "reconstitute" with some lacquer thinner. I am not familiar with the other brand you mentioned.

As for what Norm uses I would guess it is the same as what most production finish carpenters use nowdays, nothing. for the little headless pins this isn't a bad chioce.

Robin

Re: So what does Norm really use?

#3

Re: So what does Norm really use?

Bill Howatt

>Norm uses filler - he stated this on his site a few years ago. Here is the answer from the New Yankee Workshop site in response to a question about what he uses to fill holes - the questioner had trouble getting a good color match.

"Answer:

@fill the holes aftewr to have applied a finish coat. That way you can match the color better. Then proceed to complete the finish with the final coat which will seal the filler. Good luck."

Re: So what does Norm really use?

#4

Re: So what does Norm really use?

Fred Davis

>The answer Bill quoted Norm on hole filling is a excellant way to do that operation and if you try out TimberMater wood filler , you should have trouble at all macching , since you can mix and match TimberMate.

FredD

Re: So what does Norm really use?

#5

Re: So what does Norm really use?

Karen

>I don't know what Norm uses but I use either Zar wood filler (which takes the stain fairly well) or a wax filler after the top coat goes on. I have 2 sets of wax fillers - a MinWax set and a General Finish set so those "crayons" match whatever color I've used. For other brands, I mix-and-match to get the correct color by nicking off a shaving or two of different colors then heating just a bit to melt and blend. After hardening (which only takes a few seconds), the excess buffs away to nothing.

Re: So what does Norm really use?

#6

Re: So what does Norm really use?

Glenn Madsen

>OK. Now, do these crayons stay viable on the shelf for a while? The other fillers seem to have dried/clumped/cured in the sealed containers, and I got very little value out of a purchase.

I put a first coat of Sealcoat shellac on the shelves last night, and need to make a decision about what happens next. LOML has come down with some kind of sinus thing, and is complaining about any vapors...

Re: So what does Norm really use?

#7

Re: Shelf life..

Karen

>They stay viable for up to 10 yrs so far. :)

I've had some of them that long and all it takes is a couple seconds with a bic lighter to soften them up for mixing or application.

Think of it this way.. have you ever cleaned out your kid's toybox and found broken bits of crayons in the bottom? They still color, no matter how long it's been since Little Suzie graduated from Harvard.

I've also never had a problem with the wax fill shrinking or cracking and I've been using this stuff for too many years to admit to.

;-)

http://tinyurl.com/5k93nb

A link for the MW pencils only because MW is readily available just about anywhere but they're manufactured by many companies. I can't vouch for anyone but Minwax�, General Finish� and Crayola� since they're the brands I keep handy.

Re: So what does Norm really use?

#8

I'm a fan of this *LINK*

tek,brunswick

>This works real well for nail holes. There are 20 colors to choose from in the kit and you can mix them together. The link is to Woodcraft, but other supply houses carry it as well. Use it after the final coat of finish is on. We use it to fill nail holes in Trim and paneling on commercial construction projects. Refills are available when you run one of the colors out.


SoftWax

Re: So what does Norm really use?

#9

Re: So what does Norm really use?

Tom Rex in TX

>Glenn,

Any chance of getting a picture of your shelves?

My wife is also into quilting and she is overrun with material.

I'd like to see your idea.

Thanks,

T Rex

Re: So what does Norm really use?

#10

Re: So what does Norm really use?

Fred Davis

>I have used wax sticks for years for filling nail holes on crown mould and casing etc.

A trick we use to make it go faster and easier is to dampen a cloth with Jasco Lemon oil and rub it over the hole and surrounding area , this prevents the wax from sticking anywhere but in the hole which is where you want it.

Using same cloth buff the area a stroke or two and if you matched the color good , the hole disapears.

A client was watchig one of my carpenters do this on door casing over his shoulder and exclaimed it was magic !

FredD

Re: So what does Norm really use?

#11

Re: They're pretty simple, really

Glenn Madsen

>I'll see about taking a picture later today. this computer hasn't been hooked up to the camera yet. The one I often use has a memory card slot that makes it simple.

Take a couple three pieces of prefinished plywood, slice it up on the table saw to 11 3/4 widths, and build a shelf system. Fix the shelves with your favorite method, then build the face frame in front of it, and finish that. Supposed to be really easy, until you find that you need something else from the hardware store...

My cherry was 6/4, and so I did a face frame with that, except for the fronts of the interior shelves. Those got cut down for shadow lines, and to stretch the available stock.

You should understand that in LOML's case, this will hold less than one quarter of the stash... 11' wide, by 4' high, 12" deep.