Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

cutting 45 degree bevels on table saw

Posts

cutting 45 degree bevels on table saw

#1

cutting 45 degree bevels on table saw

gfriend

>What is the safest (&most accurate)way to cut a 45 degree bevel on board end..say 17 inches wide 16 inches long? When I just lay it down flat using the table saw fence..as I get near the end of the cut the board pulls away from the fence...causing the blade to dig into the end of board.

Re: cutting 45 degree bevels on table saw

#2

JL

Re: cutting 45 degree bevels on table saw

JL

>Probably a good cross-cut sled would be the safest and most accurate. I've got a simple one that works for me. One of these days I'm going to build a fancier one with a flip stop and more bells and whistles.

Re: cutting 45 degree bevels on table saw

#3

Jesper, Denmark

Re: cutting 45 degree bevels on table saw

Jesper, Denmark

>Cutting near square boards on the tablesaw against the fance is usually asking for trouble. It is difficult not to twist the board and hold it against the fence at the same time as you push againts the resisting force from the blade. Never cut anything shorter than it's width against the fence.

Use a sled instead. Now you can hold the board firmly against the stop on the sled and the runner in the slot takes care of the twisting tendency.

The sled is easy to make if you do not have one. You can probably find a description in the articles section. Mine is a simple 1/4 inch plywood sheet with a � * 1 � inch stop 90 degrees to the fence with a wood runner in the slot.

Re: cutting 45 degree bevels on table saw

#4

Re: cutting 45 degree bevels on table saw *LINK*

John K Jordan

>You can google for crosscut sled and miter sled for lots of info and pictures. The link below has mostly 90deg crosscut sleds but I did notice a miter sled or two.

JKJ


crosscut sleds

Re: cutting 45 degree bevels on table saw

#5

Re: cutting 45 degree bevels on table saw

Tom Pilsbury (Chicago)

>Great link, John. Thanks!

Re: cutting 45 degree bevels on table saw

#6

Re: cutting 45 degree bevels on table saw

Michael Wilkins

>Some type of sled that also holds down the wood as the cut is being made. I always have problems with boards moving while being cut on a 45, so some type of hold-down system is in the works. A dedicated sled with a hold-down and stick on sandpaper on the fence should keep the board from moving.

Good luck and watch those fingers.

Re: cutting 45 degree bevels on table saw

#7

Re: cutting 45 degree bevels on table saw

Fred Davis

>Using a sled for the folks that need one is fine for cross cutting on the TS , but the statement "never cut anything shorter then it's width aganst the fence " has no meaning in practical woodworking.

FredD

Re: cutting 45 degree bevels on table saw

#8

Re: cutting 45 degree bevels on table saw

Robin Corell in Atascadero CA

>I would opt for something completly different, partly because of the jigs I have vs the ones I don't have but also because I think it is safer if done correctly. I have a 12" tall fence that slips over the top of my rip fence which then allows me to asurately hold a board on edge. I would then move the fence close to the blade with the blade leaning away from the fence and then send it through on edge. To make your miter cut with this method it requires that your board be pre cut to the exact diminsion you want prior to cutting the 45* bevel. It also requires that your set up is very acurate and that when cutting the bevel you are not cutting into the face of the board or you will have the board droping down at the end of the cut and becomeing a likely kickback.

your problem cuould have been exacerbated by an incorrevtly adjusted table/trunnion or a dull blade.

Robin

Re: cutting 45 degree bevels on table saw

#9

Re: cutting 45 degree bevels on table saw

Fred Davis

>I forgot to address the posters question about how to crosscut the board safely

Check to see if your rip fence is parallel to the blade and the cross fence a true ninety to the rip fence. Using a sharp blade as always , tilt the blade so it is tipped away from the rip fence and lay the stock face down and use the crosscut fence to push it though.

If all of these guidelines are followed , you should have no trouble with the operation.

FredD

Re: cutting 45 degree bevels on table saw

#10

Re: cutting 45 degree bevels on table saw

pecker

>My saw has a bit of heel when the blade is set to 45 degrees. I've never been able to adjust it out, and the force it exerts on the type of cuts you are doing causes the same problem.

For really critical cuts, I make the first one about 1/16" wider than I need. Then make another pass to trim off this extra 1/16". There's no sideways pull at all on the second pass, and it leaves a very straight edge.