Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Small scale pieces - thickness in proportion?

Posts

Small scale pieces - thickness in proportion?

#1

JL

Small scale pieces - thickness in proportion?

JL

>I'd like to try out some ideas and make them in a smaller scale.

For those who make small pieces - do you generally use thinner lumber? I can thickness down to 1/4" without too much trouble. I could comfortable resaw thinner pieces also - I'd just have to work at smoothing them :).

How about small scale hardware? Sources?

What are some good scales to go for? 1:2, 1:3, 1:4...?

Re: Small scale pieces - thickness in proportion?

#2

Re: Small scale pieces - thickness in proportion?

Sonja Lemon Sacramento Ca.

>Check out Google - Miniatures. You'll find a whole new world out there.

Re: Small scale pieces - thickness in proportion?

#3

JL

I don't think I want to do a 1:12 scale :).

JL

>And I see that they thickness some of the wood to 0.0625". Yikes - I can that thin veneer.

Re: Small scale pieces - thickness in proportion?

#4

Re: Small scale pieces - thickness in proportion?

Robin Corell in Atascadero CA

>3:1 or on an architects scale it is the one marked 3 will give you 1/4":1" I find this to be a comfortable scale for tables and chairs but for larger items I have used 1 1/2:1 the nice thing about using the 3'1 architects scale is that 1/4" breaks down with 1/32" incraments to represent 1/4" inch scale incraments.

To mill my lumber I use a 16" disc sander. I mark it off with a panel guage and then adhere it to a block of wood with double sided tape and sand till my mark disapears. If you lack a disc sander you could get the same results on a table saw, but I would definately use a zero clarance throat plate and make sure the sacle lumber is flush with the bottom of the block of wood.

when I design in scale I don't include edge profiles other than a round over or a bevel nor do I bother with any fancy joinery or rails and stiles or even hardware. for case goods I glue up a solid block and draw in the lines for the rails and stiles as well as the drawers.

I prefer bass wood because it lacks a distictive grain pattern which can be confusing. I also don't bother sanding or finishing.

the trick in photographing a scale model is to remove any background refrences to scale and lower your camera to a similar point s what you would use if you were photographing the full scale piece of furniture.

Robin

Re: Small scale pieces - thickness in proportion?

#5

the model 

Robin Corell in Atascadero CA

>


img

Re: Small scale pieces - thickness in proportion?

#6

the piece as built 

Robin Corell in Atascadero CA

>


img

Re: Small scale pieces - thickness in proportion?

#7

another model 

Robin Corell in Atascadero CA

>


img

Re: Small scale pieces - thickness in proportion?

#8

as built 

Robin Corell in Atascadero CA

>


img

Re: Small scale pieces - thickness in proportion?

#9

Re: Small scale pieces - thickness in proportion?

steve mackay

>Depends. Miniature is my stock in trade. If thickness of stock is what we're looking for you can go paper thin on the TS. If it needs to be clean go a bit over then run it on the bench sander applying preasure with the finger tips. Finnish up with a sanding block & calliper to check along the length. ( I missed the point did'nt I ? )

Re: Small scale pieces - thickness in proportion?

#10

JL

Thanks for the advice and the pics.

JL

>I'd rather make a 1/4" = 1" model of something and find out it didn't work than waste a whole lot of lumber.