Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Tongue And Groove Bits for Flooring??? *LINK*

Posts

Tongue And Groove Bits for Flooring??? *LINK*

#1

Tongue And Groove Bits for Flooring??? *LINK*

Thomas Skaggs, Foothills of Mount Level

>Folks,

I'll soon be milling some maple for flooring. I'll mill the thickness to 3/4". I need to do tongue and groove edges. I'll be installing with a pnuematic floor nailer.

One question, is a wedge tongue and groove the best way to go?

I was looking at the Amana set. See link:

Any other suggestions???

Thanks!

Tom


Wedge T&G Bits

Re: Tongue And Groove Bits for Flooring??? *LINK*

#2

Re: Tongue And Groove Bits for Flooring???

Bill Earl

>Tom,

I've always used a straight T&G. Depending on species and width, the shrinkage gaps during the dry months can be significant. I'd expect the wedge design would allow the groove side of the plank to lift.

Bill

Re: Tongue And Groove Bits for Flooring??? *LINK*

#3

I Prefer

Mark Mandell - Gone Round In Jersey

>to relieve the top edges by an 1/8" or so. Would be nice if they had a set that would do that in a single pass rather than handling every board 3 or 4 times.

Re: Tongue And Groove Bits for Flooring??? *LINK*

#4

Re: I Prefer

Larry in NW Ohio

>I doing the family room floor this week and ordered a set from router bits,com #3375. I`m not going to do very much, just some odd ones for the steps. So I wanted a set that I could use for other things and not just flooring. Larry in Ohio

Re: Tongue And Groove Bits for Flooring??? *LINK*

#5

Re: I Prefer *LINK*

Bill Earl

>You'll find a much wider range of choices for the shaper. The Freeborn set is pretty versatile. If you are cutting much flooring, all those separate operations really start to add up.


Freeborn cutter

Re: Tongue And Groove Bits for Flooring??? *LINK*

#6

Re: Tongue And Groove Bits for Flooring???

Wess in NJ

>I would look for a set that is made specifically for flooring. The bits in your link would work if you subfloor was perfectly flat, and we know that won't be the case. Flooring cutters put a slight bevel on the bottom under the tongue so the top will always touch before the bottom, making for a tight joint. They also round the tongue, which makes the flooring much easier to install.

I bought a set from MLCS and they are fine for the occasional use they see,they were however shaper cutters. I don't know if they make a set for the router.

Re: Tongue And Groove Bits for Flooring??? *LINK*

#7

That's the ticket, Now

Mark Mandell - Gone Round In Jersey

>If I only had a shaper plus the room to put one in the Shoebox. |;-}

Re: Tongue And Groove Bits for Flooring??? *LINK*

#8

Re: Tongue And Groove Bits for Flooring???

Mac in Indy

>Tommy,

Are you going into the designer flooring business or is this for the house or shop? I'd echo the concern about the wedge tongue/groove set not sufficiently restraining the verticle moovement during seasonal width movement. How wide are you making the boards? At 2-3 inches it probably isn't a concern but for wide boards I think it would come into play. Of course you could go old school and cut them on the tablesaw!

The pneumatic flooring stapler is the best way to install!! The one I rented was a Bostich at Home Depot.

Good Luck!

Mac

Re: Tongue And Groove Bits for Flooring??? *LINK*

#9

Ellis Walentine

I'm with Mac

Ellis Walentine

>All the flooring I've ever made or laid was regular tongue-and-groove. You want the boards to be able to shrink a bit without loosening the tolerances in the joint. Also, depending on the wood, a router bit might not be a good choice for creating the edge profile. Router bits have a very small radius, which is more prone to chipping out than a larger shaper cutter or saw blade. Some woods are friendly enough to rout, but the more brittle ones can be a problem.

Ellis

Re: Tongue And Groove Bits for Flooring??? *LINK*

#10

Re: Tongue And Groove Bits for Flooring???

Fred Davis

>You should change your sentence on staplers to read "pneumatic staplers are a fast way to install flooring"

If you want to eliminate squeaks and bond the flooring to the subfloor which is a excellent construction practice and avoid the flooring dipping in the sags between joists, then you would want a different approach.

FredD