Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Kickback Happens

Posts

Re: Kickback Happens

#26

Re: An issue with blade height and splitter

charlile belden

>Mark wrote:

Another reason I like a high blade is because it reduces the "ineffective" space between the end of the blade and the splitter.

=================

Which is why a riving knife is better - stays

close the blade around the top rear quarter of the blade - where the Dreaded Kickback begins.

As for Blade High - that much blade sticking up above the table top - a kickback would be the lesser of two evils.

charlie belden

Re: Kickback Happens

#27

Re: Kickback Happens

Vince F

>Always good to save the tropy. I'm starting back after 20 yrs, and pulled the spining, shut off blade of a 10" rad arm saw onto a 2x3 I was cuting to test things, and it stopped the blade cold, and dug into the wood. I cut off the piece and have it close by. Maybe I should put it where I can easily see it.

I have a lot of disabilities, and hopefully just didn't pay attention, or forgot the blade was spinning. I was being careful when the motor was running, and maybe the more quiet of the saw after cutting, or the motor not running, lulled me into not paying attention, or realizing it was still dangerous.

VF

Re: Kickback Happens

#28

Re: Woops...

Fred Davis

>my name is not "DownDraft Table"......

Hmmmm, has a certain panache to it Brian , sorta like "DustMaker Mike" ;-))

FredD

Re: Kickback Happens

#29

Riving knife...Riving knife...Riving knife...

HC Sakman

>As I was repeating it before I bought a saw w/riving knife, I'd repeat more after I've been using a saw with it for the last 10 months.

The riving knife was long overdue for N. America. It's finally here. Shame on OSHA.

Chico...

Re: Kickback Happens

#30

Re: Riving knife...Riving knife...Riving knife...

charlie belden

>A-phreakin'-men!

With all the hype about the SawStop, it's inconceivable that OSHA - and the U.S. Market tool manufacturers ignored such a simple, effective and inexpensive feature on table saws. Splitters have been on US Market table saws for quite a while. Not very effective - unless the saw blade is set to maximum height - but they thought to make it part of their table saws. The "anti kickback" pawls they also included aren't very effective - and often a PITA - but they were also often included on saws.

And it's not like there's not enough data on how effective riving knives are - the Euro equivalent to our OSHA has required them on ALL euro table saws for about 20 years. I think US "manufacturers" are following the Steel Industry model - wring every dollar out of every ounce of Capital Cost stuff, cut corners on production control and - gof forbid - upgrade or innovate.

Be aware though that the OSHA's euro equivalent also outlaws "blind cuts" on table saw - so Dado Blades can't even be mounted on euro table saws.

Re: Kickback Happens

#31

Jesper, Denmark

Re: Chico...Chico...Chico....

Jesper, Denmark

>It's OK with the riving knife. It is more effective than the splitte anf pawl currently used. No argument there.

On the other hand, I will get on my old soapbox and make a case for brains and paying attention as the primary safety aspect of tablesaw use.

Nothing will save you if you try to cut too small pieces, which twist and bind between the blade and the fence.

Nothing will save you if you cut long pieces, which overhang the table and tip up one end or the other and catch the top of the blade.

Nothing will save you if some idiot tries to help you by guiding the other end of the board you are cutting.

Knowldege and understanding of the forces involved will help you avoid accidents. All the other mechanical devices are just auxiliary.

Primary safety is in your own head. Period.

Re: Kickback Happens

#32

Re: Chico...Chico...Chico.... *LINK*

charlie belden

>"Nothing will save you if you try to cut too small pieces, which twist and bind between the blade and the fence. "

Actually there is something that will. It's called the GRRRRRipper. Gets your hand way above the blade, has a tall flat face to keep against the fence, tacky rubber on the underside and stays in contact with the part being cut - on both sides of the cut.

You noted that knowledge and understanding of what contributes to a kickback is important. Attached link gets into that - with diagrams - with color and circles and arrows.


Kickback parameters

Re: Kickback Happens

#33

That's all correct Jesper...

HC Sakman

>Yes, the best safety device is what we have in between our ears! (When it works well!;-)

My point is that riving knife is so simple, yet highly effective for the most common cause of table saw accidents.

Chico...

Re: Kickback Happens

#34

I still like two push sticks....

John in NM

>Though one is really more of a portable splitter or riving knife. Just a stick held in the left hand and used to hold the kerf open and keep the board snug against the fence behind the blade. Simple, cheep, and very effective.