Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Marc's Shop

Posts

Marc's Shop

#1

Marc's Shop 

Marc

>Hi Everyone,

I have frequently lurked, and on a couple of occasions, contributed. I thought I would share some pics of my way-to-small garage shop, and some projects.

Here is the shop, which contains the basics. Although I have most power tools, over the past five years, I have really started to appreciate hand tools, so I finally had to make a real workbench, which is also shown.

(First time uploading pictures, so I hope there are no problems...)

Thanks,

Marc

First Pic is entering from the house. Straight ahead is the tablesaw. Almost all the walls are pegboard, which provides me with flexible storage, you can see clamps, blades, etc on the right wall. Further down from the TS, you can see the outfeed, SCMS. Far off in the corner is a lathe and router table.


img

Re: Marc's Shop

#2

Re: Marc's Shop

Marc

>Here is the opposite wall. You can see the DC ductwork, which is 6" drain pipe. Also, the drill press, bandsaw, and drum sander. I should point out that all tools are mobile.


img

Re: Marc's Shop

#3

Re: Marc's Shop

Marc

>The back wall which has some storage, shelving, and the DC cyclone (remote controlled via X-10)


img

Re: Marc's Shop

#4

Re: Marc's Shop

Marc

>Looking in now. The right wall also has the wood storage, Planer, Jointer...


img

Re: Marc's Shop

#5

Re: Marc's Shop

Marc

>Here is the backside of the Tablesaw, with the outfeed, routertable, and the lathe in the background.


img

Re: Marc's Shop

#6

Re: Marc's Shop

Marc

>Finally, the workbench :) took a while to make, but well worth every minute of it.


img

Re: Marc's Shop

#7

Re: Marc's Shop

Marc

>Another pic of the workbench drawers


img

Re: Marc's Shop

#8

Re: Marc's Shop

George@Colonel's Workshop-Havertown PA

>Good Afternoon Marc,

Lovely bench. I believe you when you talk about solidity! It seems at home in your thoroughly capable shop.

George

Re: Marc's Shop

#9

Re: Marc's Shop

Fred Davis

>I'm with George .I like a bench that doesn't move around when you lean against it and yours does that really well , good job.

FredD

Re: Marc's Shop

#10

Re: Marc's Shop

Marc

>Thanks George and Fred.

When I first touched a handplane, I hated it. A few years ago, I finally learned how to sharpen and that I needed a solid base to work on. That was a transforming event for me :) The bed and entertainment center that I just posted where mostly finished with handplanes and scrapers. Now, I despise power sanders :)

Thanks,

Marc

Re: Marc's Shop

#11

Re: Marc's Shop

George@Colonel's Workshop-Havertown PA

>Ah yes, I remember it well, so sings the song.

Now I get angina pain every time I try to use a hand plane or manually sand an expansive surface. Now is the time for me to pay the eleectrical bill.

George

Re: Marc's Shop

#12

Re: Marc's Shop

Larry in NW Ohio

>Marc That is quite a nice shop, like the saying goes"You don`t need alot to do a good job" Excellent work. Larry in Ohio

Re: Marc's Shop

#13

Re: Marc's Shop

Stuart Hough

>What size is your shop, Marc? Looking at it gave me a bunch of ideas for my 20x20 (nominal) garage...er...shop. I just need to find a spot for all the unnecessary stuff(like old family stuff, shutters, games, etc). Thanx for the pics!

Re: Marc's Shop

#14

Re: Marc's Shop

Marc

>Hi Stuart,

I'm not sure of the exact dimensions, but it is probably 22' or 24' deep by 18' - 19' wide. I'll try to measure it later. I'm not sure the pictures show it, but there is a drop-down staircase to the attic area for storage :)

One thing I really like is on the back wall, to the left of the cabinets and shelves, I have a vertical compartment for storing plywood vertically. It is about 10" wide and stores most sheet goods that I need. If I had taller ceilings, I would have done vertical lumber storage, as that would be much easier to sift through lumber than the horizontal storage on the wall.

Thanks,

Marc

Re: Marc's Shop

#15

Hope you don't mind…

Rod Peterson -- Ormond Beach

>I took the liberty of capturing the pics and text and transforming it into a gen-u-wine WoodCentral Shop Tour.

Sometime when you have the inclination, you may want to send me some better, bigger pictures (turn off "date stamp" if you can—save me some editing time), and refine/expand the text part, too, if you want.

Rod
Editor, ShopTours.org

Re: Marc's Shop

#16

Re: Marc's Shop

Larry in NW Ohio

>Mark I was going through your pics again and noticed the DC, is that the one from a guy in Indi, IND. I can`t think of the name, maybe Dust sucker? Is he still around? Larry

Re: Marc's Shop

#17

Re: Marc's Shop

mdclor

>Larry,

It is a Woodsucker. I have one and like it although I suspect the newer Oneidas are quieter. His name is Larry Adcock. I think I read that he got a bad review in one of the rags and closed up shop shortly thereafter, too bad.

Merle

Re: Marc's Shop

#18

Re: Marc's Shop

Marc

>Yep, it is a Woodsucker, one of the originals. Unfortunately I think Woodsucker is no longer :(

Marc

Re: Marc's Shop

#19

Re: Marc's Shop

Marc

>Hi Stuart,

I finally measured it, and it is 23' x 18' Send me email if you have any questions on things I have done.

Marc

Re: Marc's Shop

#20

Re: Hope you don't mind�

Marc

>Hi Rod,

Thanks for posting it!!! Perhaps someday I'll clean it. There are some other pictures I would like to take :)

Thanks,

Marc