Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Pie cut drawers?

Posts

Pie cut drawers?

#1

Pie cut drawers?

Keith Newton, LR, Arkansas------WebKitFormBoundary

>I have a customer wanting me to make a little drawer cabinet which will be octagonal, with wedge shaped drawers which are all of the way around on all eight sides. So each one will be a 45� triangle ~, except the back corner will be squared off, and actually a fourth side.

I was wondering before I bight off more than I can chew, if anyone had any neat trick for some sort of locking corner joint which would be better than just glue and brads, but not as time consuming as hand cut dovetails.

I will probably need to get a special cutter ground, unless there is something out there. Any thoughts?

To flesh out the project a bit more, there are 11 tiers high, so 88 drawers. Since there are actually four sides, 352 sides, x 2 ends, = 704 ends to cut on small some very small parts, I need something that can be jigged up for safety too.

Re: Pie cut drawers?

#2

JL

I hope you are charging enough!

JL

>88 drawers is an awful lot of drawers!

Re: Pie cut drawers?

#3

Finger joints

Paul in NJ

>

Re: Pie cut drawers?

#4

Re: Pie cut drawers?

Curly Smith

>I'd consider one of these: Small Drawer Lock Bit. A larger version is also available.

Re: Pie cut drawers?

#5

Re: Pie cut drawers?

Grant in Iowa

>Splined miters are what I would do. Easy, strong, fast and good looking.

You start by cutting the miters and gluing them up. Cut the miters using a shop made jig or a tenoning jig.

For the Glue up, I use pallet shrink wrap as a clamp. Glory of this is that you don't run out of clamps during a production run.

After a couple hours, peel off the shrink wrap and cut the saw kerfs at the table saw using a tenoning jig or shop made jig to hold the piece in place.

If you plan to use a bearing guided bit to trim the splines later, make sure you check how high your bit can cut and keep you plines close enough to the edge of the drawer to allow you to trim them.

Once the spline slots are cut, resaw and plane some stock to the thickness of your sawblade, cut out triangles from this stock and glue them in place. I shrink wrap the part again to prevent the splines from creeping out as the glue sets. I let the glue dry again and cut most of the excess off at the bandsaw. Then I use a bearing guided bit in the router table to clean up part the bandsaw left. A quick sanding and you are done.

Since you are doing drawers, don't forget to put the bottoms in before you glue it up!

This would go pretty quick for a production run. I would consider using Baltic Birch ply for the drawers and then a wood that complemented the main casework for the splines. Solid wood also works and looks great. Consider putting a bullnose on the top edge of the drawer stock before cutting them to length for a nicely rounded drawer carcase.

Here is a flag case I did with them:

Regards,

Grant in Iowa


img

Re: Pie cut drawers?

#6

Re: One more thing I forgot to mention: *LINK*

Grant in Iowa

>I use packing tape (the clear, 3M kind that is about 2" wide) for the glue-up. Then to further tighten and clamp the part, I use the shrink wrap stuff as I said. A demonstration of how that works is here(see the "Mitered boxes of any size" section):

Regards,

Grant in Iowa


gluing and clamping strategies at Taunton

Re: Pie cut drawers?

#7

Re: Pie cut drawers?

galen V

>Wonder what little is to know drawer stock thickness. Armoire with 6" sides to set on a chest or 12" and set on its own legs. Customer must have a lot of rings or ear rings to go in so many small drawers. Maybe they just want look of drawers on all side? False drawer fronts on four alternate sides with others with square drawers. Two deep and the other two shallow at 90 to them. Or one divided drawer that pulls from either side and the other two shallow at 90. Hard to imagine they open right drawer out of 88!

The customer is always right for the right price I guess!

Re: Pie cut drawers?

#8

Thanks Curley and Grant

Keith Newton, LR, Arkansas------WebKitFormBoundary

>I already have that bit, as well as another of that type, but that is too big, and since the side will be at 67.5� to the front, I am wondering if the short grain parts on a custom made one would really work very well.

I like the idea that Grant proposed with the splines, except for them showing on the front. Although I could go back and veneer the fronts to hide them there.

These drawers will be pretty small, only about 7.5" along the front, and < 9 on the sides x 3" high, so I am thinking probably 5/16' thick. The customer has chosen cherry.

As for glue, I am toying with the idea of the medium cyanoacrylate, thinking that I might just be able to fit the front to one side, and jam it into a fixture quickly after a sprits of activator, then fit the bottom and other side, and not spray, or maybe do it after getting it together. Also using it for the splines.

I appreciate that thoughts you guys have given. The process is taking shape better than I was thinking.

Re: Pie cut drawers?

#9

Re: Pie cut drawers?

Robin Corell in Atascadero CA

>I usualy use 3/8" for drawers that size. For joinery LV used to cary a router bit that makes a bird beak joint and they had diferent angles for making six, eight,ten sided containers. I don't know if one of these could work in place of a drawer lock bit but it would be worth a look. The other option may be one of those tilt bases for your router table.

For assymbly I use hot hide glue. it is perfect for rub joints that are at odd angles. It is also a bit easier to work with than CA.

88drawers @ $200/drawer = $17.6K + casework and it would still have the potential to turn into the job from hell

Robin

Re: Pie cut drawers?

#10

Re: Pie cut drawers?

Barry Irby

>Pleasants Hardware in Richmond, VA has an antique screw cabinet very similar to your description. If I were home I could go look at it and tell you hopw the old timers did it. Their's is on some sort of lazy susan bearing I think. It's not for sale and not in use, just there for the nastalgia.

Re: Pie cut drawers?

#11

I need to move to CA

Keith Newton, LR, Arkansas------WebKitFormBoundary

><88drawers @ $200/drawer = $17.6K + casework and it would still have the potential to turn into the job from hell.>

I sure wish I could get that much, but I think I can do them a bit cheaper than that once I jig everything up. Although I know the potential for deep do lingers there.

Re: Pie cut drawers?

#12

Barry, This will be on bearings too.

Keith Newton, LR, Arkansas------WebKitFormBoundary

>I wish this was more functional. I don't know what for, or if it will ever have a use, but that is not my worry.

I really like this customer. We have talked about other projects like a coffee table which would have a glass top, with a wood base which would be a puzzle. He is one of very few people who could work some that I made a long time ago.

I had a new one in mind that I thought it would be fun to ship it to him un-assembled to see if he could work it without ever seeing it together.

Re: Pie cut drawers?

#13

I missed it on the first read!

John in NM

>88 drawers! 88 triangular drawers! You have my condolences, perhaps we should be taking donations to get you that big bottle of ibuprofen from Costco.

I definitely want to see some pics!

Perhaps your client is a fan of The Nails.

Re: Pie cut drawers?

#14

CA

Phil Joines Krum, Tx

>I've herd CA deteriorates in about 10 years and joints made with it can come apart.

Re: Pie cut drawers?

#15

Re: CA

Keith Newton, LR, Arkansas------WebKitFormBoundary

>Really? Is there good research on that? I hate to hear that if it is true.

Off to do a search. thanks.

Re: Pie cut drawers?

#16

JL

Re: CA

JL

>Low temperature would weaken CA as would exposure to certain other things (mostly solvents). I'd be more concerned about it's brittleness and relative weakness as opposed to other adhesives. How about using a 5 minute epoxy?

Personally I'd prefer a glue with more open time like hide glue. I always screw something up when I do drawers :).