Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Forrest Blade Update

Posts

Forrest Blade Update

#1

Forrest Blade Update

Tony - Memphis

>Well, I got my blade back and installed it last evening with high hopes....same issue exists. So, I have confidence that Forrest sent me a blade back that is just fine and started working at it with that assumption.

What is happening is that the workpiece (crosscutting here) is cut by the rear teeth (I'm calling the rear the teeth furthest away from me, the operator) as the workpiece is pushed past them. If I stop and return the piece before the whole piece goes past the rear teeth, I get a partial cut (see previous post - or maybe this one if I still have the pic). So, I'm scratching my head trying to figure how that can happen. The thing I keep thinking of is that the miter gage path is at an angle to the blade slanted towards the rear teeth? But, I keep telling myself that I haven't changed a thing since I mailed the blade off. But then I recall that I did "tune" the saw before I mailed it. Aha! I wonder...did something I do then change things and I didn't notice since I didn't do a lot of cutting between the "tuning" and the mailing of the blade?

I did adjust the slot to blade (I have PALS). I checked it with a MasterPlate and it checks pretty well. But then I was reading this morning about a problem with the PM2000 heeling as the blade is raised. So, then I got to thinking that the dial indicator isn't telling the whole story. Wish I could remember how much I corrected and where. I'm gonna start writing these things down. Anyway, that's my current theory and I plan on doing some testing tonight and/or this weekend.

I hope they have corrected the problem with the PM2000's as I may take advantage of the Woodcraft sale this weekend and order one. Tough decision.

Thanks for the help.

Tony

Re: Forrest Blade Update

#2

Re: Forrest Blade Update

Bill Tindall, E.TN

>First, thank you for keeping us up with this mystery.

In the picture it looked like the "back" teeth cut into the cross cut in one spot. This pattern is consistent with the blade going unstable at that point of the cut and fluttering. The only way I can think of to produce the pattern in the picture is for the blade to flutter at that point in the cut. If the back teeth were dragging all the time the evidence would be a burn or funny fine teeth marks, not one gouge of a tooth height in width. You might repeat the cut with out the stabilizers.

Try a cross cut where the cut is less than a blade width. This cut will not load the blade and likely eliminate any blade flutter, if that is the problem. If cut is smooth, you don't have an alignment problem, you have a stability problem.

Re: Forrest Blade Update

#3

Re: Forrest Blade Update

Tony - Memphis

>Well, the cuts I was doing last night did produce some burn and some coarse tooth marks. Don't have a pic of those. Good thought on trying without the stabilizers. I'll add that to my test.

Tony

Re: Forrest Blade Update

#4

Re: Forrest Blade Update

Ralph Turney

>I hate to say this, but it sounds to me like you just don't have the blade parallel to the miter slot. After all, you did make an improvement. Have you tried to move the blade back and forth, standing at the left side of the saw...like there is play at the arbor? If you have a problem, always go back to your last improvement.

Sorry you're going through this.

Ralph

Re: Forrest Blade Update

#5

Re: Forrest Blade Update/SawStop

David

>If I read correctly, you're considering a new table saw. Consider the SawStop, it was designed by a guy with a PhD in physics. It is a dream to adjust, no reaching around and contorting your body to make adjustments. Minimal backlash in the gears. The miter slots are trued to the Master Plate by loosening a bolt on the back of the table, outside; then, merely loosening one set screw and tightening another set screw on the sides near the rear of the maching. First try, I took out .008" runout, it took less than 5 minutes.

The 5HP motor saws through anything. It also adusts for true with the blade beveled at 45 degrees. The base it has is also a dream, my 2 year old niece could push it around, when the machine is "up". this will by a saw someone will get when I die, and hopefully use it.

I love my Forrester Woodworker II blade and clean the pitch off every so often. A clean blade is a happy blade.

Good Luck, David

Re: Forrest Blade Update

#6

Re: Forrest Blade Update/SawStop

Scott in Montana

>I've got to say that I am also impressed with the big Saw Stop (5hp). I have a very well tune Powermatic 66 and the Saw Stop is every bit as good of saw and maybe better; not to mention safer.

Back to the original problem at hand. While I've tried to read most of the responces concerning this maddening problem, I know I've missed a few and maybe I've just plain forgot, but has anyone addressed the possibility of bad belts on the saw? I suddenly picked up a vibration on my saw and burn marks once and everything looked perfect, but I replaced the belts and the problem was solved. I took the belts into the place that specialiazed in belts, bearings, and pulleys and he cut it in half and showed me where my stranding had started to break apart although the belt appeared normal from all outside inspections. Maybe like a car tire with the belts separating? Just a thought, and it may have already been addressed.

Again, good luck!

Scott