Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Using particle board for router table

Posts

Using particle board for router table

#1

Using particle board for router table

Dan Mitchell

>I'd like to build a router table, initially at least to house my Hitachi M12V. Recently picked up an especially nice 30" x 48" piece of 3/4" underlayment particle board from the cull bin at HD for $0.51. I know birch plywood would probably be superior, but I'm thinking I could glue up a double thickness (1.5") of this stuff, cover both sides with some formica I have left over from building my TS outfeed table, and have a nice top for a router table. Hylton's "Router Magic" mentions something about particle board being "probably OK" but that it might "possibly disintegrating from the vibrations of the router". Anyone use particle board successfully over time in this application?

TIA

Dan

Re: Using particle board for router table

#2

Re: Using particle board for router table

paul waddle

>Lots of people do just as you intended. They stress laminating both sides. The rub comes in mounting the router. If you inlet the router,this material gets weaker at that point. Most buy a router plate and beef up the underside. Seems like a great idea,unless you can afford Baltic birch. pw

Re: Using particle board for router table

#3

Re: Using particle board for router table

Barry Irby

>Dan,

I made my router "table" (wing for my TS) out of two sink cutouts from a kitchen cabinet maker friend of mine.

The cutouts had plastic laminate on them already and I glued them with yellow glue back to back. Without that they tend to get a cup in them or become concave on the laminated side, but gluing them seems to cancel that out nicely. They are particle board.

I cut out the hole for my home made router plate. I mad the hole full sized and then glued in oak strips to form the ledge or rabbet for the plat to sit on. I put an "adjustment" (drywall) screw in each corner and one centered on each side. That way, the screws are screwed into the hardwood and not the particle board.

Been fine for years. Should have made the hole bigger to accommodate a larger router and still could if the urge strikes me.

Before I laminated the two pieces together, I cut slots in the edges and installed some bolts that stick out like studs to attach it to the TS.

The only thing I am skeptical about is cutting a slot in the laminated top for a track for a miter gauge or whatever. The slot would sever the laminate on the top side and part of the particle board. Don't know for sure, but it seems to me it would warp at that point. I would want some sturdy ribs on the bottom side for reassurance.

Re: Using particle board for router table

#4

Re: Using particle board for router table

Jim Dillon

>Dan,

Sounds like it is very doable, especially if you double up the thickness plus laminate on both sides. If you are really worried, you could, as Barry suggested, build a supporting frame surrounding the router plate opening, but I don't think that is necessary in your case. On my router extension table, I used 3/4 inch MDF (a flexible material) but supported it underneath with 1 x 4s on-edge. Seems OK after 10 years or so. You will be fine.

Jim

Re: Using particle board for router table

#5

JL

Re: Using particle board for router table

JL

>It should work, but consider a few things.

Do you want to put a T-track in the top (really nice for jigs and miter gauges)? Can your particle board have a dado cut or routed in it to accept a T-track? Make a test cut or two.

How are you going to attach your fence (if you have one) to the table top? Are you going to use slots? T-tracks?

Don't get me wrong, I'm not saying you shouldn't use particle board - I'm just saying you should plan. I've picked up many a "roll" support of thick (1-2") particle board from where I used to work. They make great jigs.

My $0.02.

Re: Using particle board for router table

#6

Did just what you want to do....

Terry Alexander

>....about 8 yeas ago. No sag, used a above the table router adjustment plate, router is an MV12 (just like yours). Fence is hand made and clamped at each end with "C" clamps. Very very easy to adjust and remove when needed.

IF I ever build Norm's router table, I am still going to make/use the exact top construction technique that I currently have.

Go for it and enjoy for many many years.

Terry Alexander

Re: Using particle board for router table

#7

particle board/melamine

Robin Corell in Atascadero CA

>My first router table was made from 3/4" particle board sealed with lacquer. It had a support on either side of the opening and lasted for almost 10 years till I upgraded my table saw. My current router table is the right hand extensin on my cabinet saw and it is made from 3/4" melamine, which is still particle board. There is a 1x2 support on one side of the opening and after 10 years there is no noticeable sag. My router plate is 3/8" phenolic and the router is a Dewalt 625.

Robin

Re: Using particle board for router table

#8

Re: Using particle board for router table

Tony - Memphis

>I bought a Woodhaven router table many years ago. It is made of some sort of man made particle board (not sure what it really is, but the particles are fine and it looks similar to mdf - maybe a bit more coarse). Top and bottom are covered and it is over an inch thick. It has held my MV12 for many years. It hasn't sagged much. Actually, my plate sagged. I replaced it recently and checked it all with a nice Starrett straight edge and it all looks pretty good. I was satisfied with some fussy work I was doing. So, I say go for it. Good buy on the material! Using the Hitachi in a table is a real pleasure. I added a Router Raizer a couple of years ago and it has been real nice to have. Not needed, but a nice convenience. I had to remove the handles of mine to fit it through the insert hole, btw. Also removed a spring to make it easier to adjust with the Raizer. Oh, and the adjusters tha Woodhaven uses to level the insert are really nice. I'm sure you can do something similar shopmade.

Tony