Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Good dovetail router bits

Posts

Good dovetail router bits

#1

Good dovetail router bits

teflon_jones

>Hello,

I started up my woodworking shop last year and so far have just done one piece due to relocating from Mass to Colorado. Right now my shop is stacked up in the garage of the house I'm renting. Thankfully, I close on a house next week and my shop will be back in action within about a month!

Anyway, that's just setting the basis for my question. I bought a brand new set of Craftsman router bits last year and used them to cut about 20 dovetail joints in pine. However, the bit I used did a terrible job from the start and burned the wood! I used other bits from the same set and they cut just fine. So why did this bit do so terribly? It was a regular 1/2" dovetail bit. I have a couple of pieces to build for my new house and will need to cut a bunch of dovetails. What is a good brand of bit to buy? I'd like to invest in a really good quality dovetail bit or bit set of maybe 3-4 dovetail bits. But I'd still like to understand why the new bit I used did so badly. I was cutting the dovetails freehand on a router table with a 1.5 HP Craftsman router.

Re: Good dovetail router bits

#2

Re: Good dovetail router bits

del schisler

>This is my opion Sears didn't make those But they are cheep and I wouldn't buy them Get these Amana or whiteside their are some more company's that make good one's I buy amana they are at my cabnet shop supply place And close by They are sharp and good You will be suprised with a good bit Just don't buy from the box stores also Cheep

Re: Good dovetail router bits

#3

Re: Good dovetail router bits

Mike S.

>There's any number of reasons that you would get burning from your bits. It could have been speed, feed rate, or an improper ground from the factory. I've never been a big fan of Craftsman and don't have much experience with their bits. I use mostly Freud, CMT and Whiteside bits and don't experience many problems. Another thing that you can try to in order to minimize burning (particularly in larger dovetails) is to get rid of most of the waste with a straight bit and then follow up with the dovetail bit to finish the job.

Re: Good dovetail router bits

#4

Re: Good dovetail router bits

Hamish

>I second Mike's opinion. You could also try Trend bits. They are good too.

Re: Good dovetail router bits

#5

Her-Saf *LINK*

Robin Corell in Atascadero CA

>I have always prefered Whiteside or Amana for my work horse bits and tend to opt for CMT for ocasional use bits. Recently I have started using Her-Saf bits. They are every bit as good as Whiteside and are also made in USA. Her-Saf specializes in making carbide insert tooling for CNC routers. I recently bought a dovetail bit from them and it is a bit different from most bits in that it is a two piece design. there is an arbor that is avalable in diferent diameters as well as different lengths, a real plus for plunge routers mounted in tables. the bit portion screws on and can be changed to a sharp bit without loseing your set up. this feature allowed me to cut the dovetail on my table and the sliding porton with my trim router using the same bit for each operation and not having to loose the set up for either in case I needed to redo a part. the other nice thing is that I was able to use the same bit on a 1/4" shaft arbor in my trim router and then switch it to a 1/2" shaft arbor for my plunge router.

Her-Saf tooling is generaly very expensive compared to most catalog stuff. The only reason I am mentioning it is that I wish I had known about it before I spent a bunch of money on some of the other bits I have.

Robin


Her-Saf