Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Table Saw Dust collection?

Posts

Table Saw Dust collection?

#1

Table Saw Dust collection?

WarrenC

>I just finished building the Bill Pentz dust collector and hooked it up to my Table Saw. I dont have an overarm collection, nor will I ever get one. As you can imagine, I still get sawdust on top of the table. Would it be detrimental to drill some holes in my zero clearance insert to try capture some of the dust?

thanks

Re: Table Saw Dust collection?

#2

Re: Table Saw Dust collection?

Larry Marker

>I don't think it will do you much good. That dust comes off at a pretty high velocity and I don't think a few holes in the top of the insert would capture much of it.

Why will yuou not ever have an overarm collector?

Larry

Re: Table Saw Dust collection?

#3

Re: Table Saw Dust collection?

Chuck in ND

>Warren, I think most of the dust you get on the table is comeing from the back of the sawblade and then ontop of the board being sawn. I don't know of any other way to capture it other than a over the blade dust hood, such as a Shark Guard, etc. Out of curiosity, what type of tablesaw are you useing ? Contractors ? Hybrid ? or Cabinet saw ?

Re: Table Saw Dust collection?

#4

Drilling holes will not help....

Howard Acheson

>If you think about it, any board you are cutting will cover any holes in the ZCI so no suction will get to the dust on top of the board.

The only way to capture dust on top of the board is with an over arm collection system.

Re: Table Saw Dust collection?

#5

Re: Drilling holes will not help....

Alan in Little Washington (NC)

>Like Howard said your stock will cover the holes and most of the dust is being thrown off the top front of the blade.

I don't like the big, bulky, plastic over-blade guards/dust shrouds, so am going to make one with a fixed solid lexan top placed about 6" above the table, but with a soft skirt instead of hard sides. That should contain the dust until it is sucked up the overhead pipe, and still allow boards to slide under it easily without the need for a parallelogram or other pivoting mechanisms. Its purpose will be for dust only, and it will NOT be a blade "guard".

Re: Table Saw Dust collection?

#6

Re: Table Saw Dust collection?

Glenn Madsen in the SF Bay Area

>"Why will you not ever have an overarm collector?"

Not the OP, but in my case, the saw sits at the front of the formerly used as a garage space, and the overhead door rolls up over the machinery. There is no overhead place to run the goodies.

And I can live without it, anyway. There's far more stuff tossed from the lathe, the routers, the sanders, the handsaws, the handplanes, and the like than an overarm collector can catch.

We'll just leave the safety discussion for another thread. Maybe.

Re: Table Saw Dust collection?

#7

Re: Drilling holes will not help....

Warren Chernoff

>I have a General T-650 saw with a Shark Guard. I've run 6" PVC pipe all the way to the dust port on the bottom of the saw, with a vertical run of pipe at the back right hand corner of the saw. If there was some way of tapping into this line with a 2" pipe, I would consider running it to the Shark Guard. However, if I need to reduce, I'm going to have to run some pretty bulky stuff over the saw, and dont want to do that.

does anyone know if there is anyway to tap into a 6" PVC pipe with a 2" fitting?

Re: Table Saw Dust collection?

#8

adjust expectations

Bill Tindall, E.TN

>Short of industrial sized dust extraction a home shop system is not going to capture everything. I just finished sawing some and the top of my saw has a layer of dust, actually fine chips, on it. I have a 2 HP Oneida sucking on the saw with flow strong enough to grab bench brushes out of my hand (recent occurrence). I suspect the finer saw dust, that with less momentum, is captured because what I have to brush off the table seems to be the larger stuff.

Re: Table Saw Dust collection?

#9

Re: adjust expectations

Warren Chernoff

>the reason I'm against an overarm collector is because of the bulky pipe I would need to run. Because of supplies that are available to me, I would have to tap into my existing line with a 6" Wye, then reduce it to a 4", then to a 3" and finally make an adaptor to fabricate my own 2" connection so I could run some flex to the guard.

Any way to tap into my existing line with just 2"


img

Re: Table Saw Dust collection?

#10

Re: adjust expectations

Glenn Madsen in the SF Bay Area

>Any way to tap into my existing line with just 2"?

When I did mine, I took some pieces of what I had down to the hardware supply store, and we cobbled something together out of plumbing parts. Much cheaper/better than Rockler...

Re: Table Saw Dust collection?

#11

Re: Table Saw Dust collection?

Larry in NW Ohio

>What I did was to make a "donut" out of plywood. The OD would be the size of how good it would fit the pipe and then cut a hole the size you need for your 2" Good luck Larry in Ohio

Re: Table Saw Dust collection?

#12

Re: adjust expectations

Curly Smith

>You can buy a 6" to 2" reducer (example here: 6" x 2" Reducer Bushing Spig x Slip PVC Fitting). Your local plumbing supply house is probably cheaper though.

Or, you can drill a 2 3/8" hole in a 6" end-cap and glue in a stub of 2" PVC. 2" couplings on either side of the end cap will hold the stub in place and, if you cut the stub slightly shorter than needed, a liberal application of adhesive will glue everything together and give you an air-tight seal.

Re: Table Saw Dust collection?

#13

Re: Table Saw Dust collection?

Chuck in ND

>I can't imagine that there isn't such a thing as a 6" X 6" X 2" Wye, I know I've seen them before.