Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

QSWO Quadralinear Legs for Prairie Chair

Posts

QSWO Quadralinear Legs for Prairie Chair

#1

QSWO Quadralinear Legs for Prairie Chair

Ed in Lawrence, KS

>I'm just starting a L&JG Stickley #416 Prairie Chair from Robert Lang's plans. First up - the legs. Each is 2-1/2" square and should show quartersawn grain on each face. There are several ways to do this, but I was convinced by reading Mr. Lang's books that I should try the method employed by Stickley (Gustav, I think) which involves rabbeted miters. I could have laminated several approx. 2-1/2" x 1-1/4" pieces together and and used veneer on opposing sides to get my 4 QS faces, but I've heard several people dicuss issues with the veneer splitting over time, and the hardwood supplier I use now doesn't stock the 6/4 QSWO I'd need for the 1-1/4" stock. Plus, the rabbeted miters intrigued me and looked like they would be a challenge to make. I've included several photos here to show most of the processing steps. The first is the stack of stock I prepared for 4 legs - 16 pieces, 2-1/2" wide x 27" long x 1" thick. To make this as easy as possible, the width and thickness measurements were held as tight as I could get them.


img

Re: QSWO Quadralinear Legs for Prairie Chair

#2

QSWO Quadralinear Legs for Prairie Chair - Step 2

Ed in Lawrence, KS

>Here, I've cut the grooves on the inside faces of each piece. Each groove will be intersected by a 45 degree miter.


img

Re: QSWO Quadralinear Legs for Prairie Chair

#3

QSWO Quadralinear Legs for Prairie Chair - Step 3

Ed in Lawrence, KS

>And here, I've cut one of the miters. The first miter is cut with the TS fence to the left of the piece. The second miter is cut with the fence to the right of the piece. By the way, I used several spare pieces for set-up. They were invaluable and gave me the confidence that I wasn't about to create a pile of firewood.


img

Re: QSWO Quadralinear Legs for Prairie Chair

#4

QSWO Quadralinear Legs for Prairie Chair - Step 4

Ed in Lawrence, KS

>Here's the final assembly, after the final miter was cut. Until you get to this step, you really don't know if it's all going to fit together like you want. I was pleasently surprised that everything seemed to fit well. I wasn't able to glue the legs up the day I cut them, so I was a little concerned that I'd get some movement over night. There was some movement, but not enough to cause any great problems. To glue the legs up, I first went and purchased some Titebond III. I wanted the extra open time that the glue provides. Second, I determined what piece was going where on the legs, the most highly figured pieces being used for the show faces. Third, per Mr. Lang, I placed each piece face side down and used clear packing tape to tape 3 of the corners together (I put the tape down on my saw sticky-side up and placed one piece down then the second). Fourth, I applied glue to 1 miter face of each corner joint and then folded the assembly in on itself. Last, I used several clamps to squeeze the final corner closed, afterwhich I wrapped the assembly in more clear packing tape. I took the tape off last night and am very please with the results. I learned several important things while making these legs: 1.) Use a rear, less critical leg as your first assembly. I'm glad I did. 2.) Only coat 1 miter face of each corner with glue. Coating both faces is too much glue and makes it really tough to close the joint (a friend told me this :)) 3.) Run the packing tape along the entire length of each corner joint. If you don't do this, the glue runs out of the joint when you close it and it makes a real mess (the same firend told me about this). and 4.) Like with any glue-up, have everything you need, plus everything you don't think you need ready before you start (my friend is a genius).


img

Re: QSWO Quadralinear Legs for Prairie Chair

#5

JL

Re: QSWO Quadralinear Legs for Prairie Chair - Ste

JL

>Thanks for showing. How much "waste" do you have doing it this way? Can (or do) you use the trimmings as part of the project? QSWO is not the least expensive of woods :).

Re: QSWO Quadralinear Legs for Prairie Chair

#6

Nice Work Ed!

Bob Lang

>

Re: QSWO Quadralinear Legs for Prairie Chair

#7

Re: QSWO Quadralinear Legs for Prairie Chair - Ste

Ron Jones

>Not only did you do nice work; you did a very good job of explaining what you did! Thanks for sharing both with us.

Re: QSWO Quadralinear Legs for Prairie Chair

#8

Re: QSWO Quadralinear Legs for Prairie Chair

Alan in Little Washington (NC)

>Nice work! Had you considered using a router table and a lock miter bit?

Re: QSWO Quadralinear Legs for Prairie Chair

#9

Re: QSWO Quadralinear Legs for Prairie Chair

mdclor

>Ed,

These look really good. When I did this, I used splines on the miters. I think the process you used looks better. What are the dimensions of the grooves? They look like 1/4" by 1/8". Would the groove vary with the dimension of the leg?

Thanks,

Merle

Re: QSWO Quadralinear Legs for Prairie Chair

#10

Re: QSWO Quadralinear Legs for Prairie Chair - Ste

Ed in Lawrence, KS

>JL, if you figure that I cut off a piece 1" wide x 1" thick piece from each 2-1/2" wide x 1" think piece (actually, 2-45 degree triangles with 1" legs when viewed from the end), that's 40% waste. That's the same, though, as if I'd chosen to use standard miters or lock miters. I think I paid about $4.50/bf for 15 bf of 5/4 stock. Between cutting around knots and the waste from the rabbeted miters I got my 4 legs out this. So my legs cost $67 of which I wasted about 40% in the rabbeting process, or $27. It was worth it, both for the experience and the end result. And remember, my local supplier didn't have 6/4 that I could have gotten the 1-1/4" stock from.

Re: QSWO Quadralinear Legs for Prairie Chair

#11

Re: QSWO Quadralinear Legs for Prairie Chair

Ed in Lawrence, KS

>Alan, at first I was going to use a lock miter bit and use my router table. But I've heard that lock miters are fussy to setup, too, so I figured why not use the tools I already have. Plus, good lock miter bits are a little expensive and I don't think I'd use one that much. I also admit that I was drawn to the challenge of cutting the rabbeted miters. It was fun and very satisfying.

Re: QSWO Quadralinear Legs for Prairie Chair

#12

Re: QSWO Quadralinear Legs for Prairie Chair

Ed in Lawrence, KS

>Merle, the grooves are 1/8" deep and my two Freud dado blades wide (about 1/4"). The only critical dimensions, though, are the depth and where the edge of the groove closest to the middle of the face is. In fairness, the groove has to be at least 1/8" wide (in my case) but anything over doesn't matter. If the width of the leg changes, the only thing that will change will be the position of the groove on the face, not the depth. To get this all straight in my head, I used SketchUp to make myself a scaled drawing. This was very helpful.

Re: QSWO Quadralinear Legs for Prairie Chair

#13

What is the purpose of step 2, grooves?

Bill Tindall, E.TN

>

Re: QSWO Quadralinear Legs for Prairie Chair

#14

for the rabbit, I think - but I'm confused too.

Tim Greif - West of Chicago

>He refers to a rabbited miter. The grooves are placed to create the rabbit after cutting the miter. I understand the concept but am having trouble understanding the benefit it brings to this glue-up. It seems way too small to offer any strength advantage. Scratching my head here, west of Chicago.

Re: QSWO Quadralinear Legs for Prairie Chair

#15

Re: What is the purpose of step 2, grooves?

Curly Smith

>If you enlarge pic #4 and look very closely to the upper left of the center hole you'll see the rabbet that runs the length of the joint. The rabbet is created by the groove. In addition to adding strength, it may aid in glue-up but that's just a guess on my part.

Re: QSWO Quadralinear Legs for Prairie Chair

#16

Why the grooves

Larry in NW Ohio

>My take on the grooves is that if you take a real close look. with every cut being the same, the edge on the groove with the 45 ending up to it will make it easier to glue up. Look at the picture where they are glued, each 45 stops where the45 meets the groove. At least thats my story and I`m sticking to it, at least till I hear something better. Larry in Ohio

Re: QSWO Quadralinear Legs for Prairie Chair

#17

Re: What is the purpose of step 2, grooves?

Bob Lang

>The rabbet keeps the miters from sliding around when you glue up the assembly. It might be a bit stronger, but if the miters fit along the length no additional strength is needed. This was originally used in a factory setting, and the joints milled on a shaper or molder. Makes more of a difference in a production setting-easier to justify the machine setup.

Bob Lang

Re: QSWO Quadralinear Legs for Prairie Chair

#18

Re: What is the purpose of step 2, grooves?

Ed in Lawrence, KS

>While I was futzing around trying to draw a picture in Word (I have limited CAD ability here at work) and creating a JPG for uploading to WC, I see that Bob Lang posted a response. Here's a cellphone picture of the Word drawing on my computer that will hopefully provide a little more information. By using this method, you can mill all 4 pieces with one setup and still wind up with interlocking joints. You could cut rabbeted miters on two opposing pieces and straight miters on the other opposing pieces, but this would entail 2 different thicknesses of wood and two set-ups. As I said originally, I wanted to be authentic, but also enjoyed the challenge that the rabbeted miters provided. YMMV


img

Re: QSWO Quadralinear Legs for Prairie Chair

#19

thanks

Bill Tindall, E.TN

>I'll bet that set up too a bit of effort to get right!

Re: QSWO Quadralinear Legs for Prairie Chair

#20

Re: What is the purpose of step 2, grooves?

Don at Central Illinois

>Thnaks. I was having a little trouble grasping the concept. This last picture clears it up.