Thanks!
Tony - Memphis
>Looks great!
Knowledge You Can Build On — Est. 1998
Thanks!
Tony - Memphis
>Looks great!
Re: Thanks!
Chuck in ND
>I think I now have the saw about as modified as I'm going to get it. I bought it new with the 30" Unifence and mobile base about 15 years ago. Just over the last couple years I've added a Fenner Drives PowerTwist link belt, switched the motor to 220, added a more convieniant on/off paddle switch up by the fence after makeing a mount for it, designed and built dust collection for it thats next to perfect in my opinion, and now added the outfeed table. I wish I would of done all this 15 years ago when I bought the saw. About the only thing I can think of that I'd like to try on the saw now are a set of PALs.
Re: Switch upgrade
Chuck in ND
>I removed the small toggle switch and electrical box that would fill with saw dust from the cabinet and installed a new paddle switch up by the fence rail.
Re: Table saw DC
Chuck in ND
>Here are the results of the dust collection upgrade I have designed.
Re: Switch upgrade
Chuck in ND
>This is a Woodtek switch from Woodworkers Supply. It also comes with a plastic electrical box. I made the mount for it to bolt behind the front lip of the extension wing where the fence bolts to it.
Re: Switch upgrade
Chuck in ND
>When wireing the box there was no butchering of the factory pigtail ends. I did however need to cut two U shaped notches from the top of the electrical box for the factory pigtail ends to slide into.
Re: Switch upgrade
Chuck in ND
>
Re: Switch upgrade
Tony - Memphis
>Well, I have to confess. I've been using my trusty Delta CS for around 13 or 14 years now. I've made a lot of furniture and other stuff with it. I've considered upgrading over the years, but I could never really justify it. I'm a weekend warrior and I really don't get as much time in the shop as I'd like. But after trying to align my saw, I was convinced that the cabinet saws were better. And now, it seems like every piece of wood I cut closes up and stops the saw. I had a clencher this weekend with a piece of 4/4 walnut. I was ripping three inches off of a 8 inch board and sure enough, it locked the blade - makes funny noises when the motor is spinning but the blade ain't! Anyway, that got me to thinking more about a new PM2000. Matter of fact, I was planning on postign a question on how others have gotten their cabinet saws from the delivery truck to the shop. I may break down soon. Still no justification, but I've been saving my milk money long enough.
Tony
Re: Switch upgrade
Chuck in ND
>Tony, I realigned my saw this weekend. I had unbolted the back trunion when I was working on the dust collection for my saw last fall and never thought much about it being out of alignment after tightening it back up, then this spring I noticed that the blade alignment was off a little. It wasn't as hard to realign as I thought it would be without a set of PALs, it took me maybe 15 minutes. In the 13 years I've owned the saw this is the first time I've adjusted the trunion. You can do what you want, but after your post I feel like I'm wasteing my time trying to help people with these types of saws. I like my saw, and I'm proud of what I have done to improve it.
Re: Switch upgrade
Chuck in ND
>This all makes me think of a post someone wrote when someone else was looking for advise, I'm not sure which forum it was in but I don't think I'll ever forget it. The guy replied by saying, don't look for rational answers here, some people will spend $100 or more on a saw blade for their table saws, then run the board through a jointer after they are done with the cut on the table saw. Now we have a guy that wants to spend over $2000 on a new table saw because he doesn't want to do the safe thing and use a splitter on his old table saw. Go figure. I think I'm about ready for that $150 an hour psychologist someone was talking about earlier.
Re: Switch upgrade
Chuck Kettler Greenwood IN
>Chuck - I have the same setup you do with the exception of having added a UniGuard. Since I added a set of PALS I have never seen the need to step up to a cabinet saw unless I find one for less than what I can get for my CS. The price difference buys a lot of lumber and other entertaining accessories. Chuck
Re: Switch upgrade
Tony - Memphis
>Well, if you are referring to me as "some guy," I never use my saw without the splitter unless I absolutely have to. I also use a gaurd and wear safety glasses and a dust mask and all the other stuff.
Some guy
Re: Switch upgrade
Tony - Memphis
>I wasn't that lucky with aligning mine. I have PALS too. What I found was that it moved after everything was tightened up. I'd work and work to get it just right, then when I tightened everything up and hung the motor, things had moved around. I finally got it setup pretty well. The cuts are pretty good. I've been using mine for 13 or 14 years. I've added a Forest blade, new fence, Brett Gaurd, shop made splitter, shop made zero clearance plate, etc. (Delta supplied a new motor for it even out of warranty). Still a good saw. It'll make a good saw for the next owner getting started in woodworking. I'll let it go for cheap to someone I know will use it and enjoy it.
I'm not sure why my wanting a new fancy saw should in any way reflect on what you are doing. I am going to follow suit if I hang on to mine. I really wish I had the knee bump switch after the blade has locked up a couple of times. Nothing like hunting for a tiny toggle switch when you are waiting for a piece of wood to go flying!
Tony
Re: Switch upgrade
Chuck in ND
>How can you say that you use a splitter when in the post before you say it seems like every piece of wood I cut closes up and stops the saw. How is that possible when useing a splitter ? What am I missing ? If your useing a splitter I'd say your arbor, or your fence is out of alignment or maybe both and is binding between the fence and the backside of your blade.
Re: Switch upgrade
Chuck in ND
>Aren't you supose to adjust the trunion with the motor installed ?
Re: Switch upgrade
Chuck in ND
>Mr Kettler I agree, I personally think Contractors saws have gotten a undeserved bad rap in recent years. When people would tell me that acceptable dust collection on a Contractors saw wasn't possible I took that challenge and after a few prototypes I finally came up with a more efficient dust hood, then people would over look that and say well what about the open back of the cabinet ? so I took that challenge on also and came up with a design that does not interfear with blade tilting operations. All this design work took me about a year to develope. Now with the other add ons that I have bought such as the Fenner Drives PowerTwist link belt, the paddle switch, the extension table, and some day a set of PAL's I have a saw that I'm very happy with. If I was to open a cabinet shop and used a saw 5 days a week or more, 8 hours a day or more, then I could justify the expense of a cabinet saw. I don't have alot of money to spend on uneccesary items. Like you say, the money I have saved so far by not buying a cabinet saw has allowed me to buy other tools that I need. For me to buy a cabinet saw would be like me buying a 5 ton flat bed truck to haul a couple boards home occassionally, sure, it would look impressive, but how necessary is it ?
Re: Switch upgrade
Tony - Memphis
>Well, I exagerated that. Not almost every piece! Its happened a couple of times lately. I'm not sure exactly what is going on. I assume that the splitter is not exactly the same size as the blade, so there is room for the wood to close up. When the last piece got stuck, I could move the piece with the blade, so it wasn't stuck against the fence. This splitter is old and may be worn enough that its time to redo it. I agree with you that there is an issue here that can be fixed. If we keep this up, it'll save me a couple of thousand dollars! I keep thinking myself in circles. About the time I decide I want a new saw, I decide I can't really come up with a good reason to buy it other than just wanting one, but then I don't really want one THAT bad. A couple of grand is a lot of wood to cut up. I'm sure the folks that are real tablesaw anal would die if they took a look at my saw. There is a big dip in the table, I still don't have it aligned "perfectly" (I believe in getting it as close as possible and forcing the error in your favor), etc.
Tony
Re: Table saw DC
Chuck in ND
>Unreal, no comments on the DC. Go figure.
Re: Table saw DC ( SawSuck ? )
Chuck in ND
>Perhaps I should of called it SawSuck, It might have drawn more attention to it, more people would believe in it, and I could get a premium price for it.