Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Mortising Machine. Magazine Reviews?

Posts

Mortising Machine. Magazine Reviews?

#1

Mortising Machine. Magazine Reviews?

Joe in a Cleveland suburb

>Hi folks.

I am considering (again) getting a mortising machine. I was looking at the Grizzly machine last night on line; $200. Nice price.

Does anybody recall if FWW recently did a review of bench top mortising machines? I kinda remember reading/seeing a review, but couldn't find it.

Thanks.

Joe

Re: Mortising Machine. Magazine Reviews?

#2

Jim DeLaney, Austintown, Ohio

Re: Mortising Machine. Magazine Reviews?

Jim DeLaney, Austintown, Ohio

>Newest thing I could find on FWW Net was issue 178 (2006), and that didn't include a Grizzly machine.

Re: Mortising Machine. Magazine Reviews?

#3

Re: Mortising Machine. Magazine Reviews?

George@Colonel's Workshop-Havertown PA

>Good Morning Joe,

Also consider Shop Fox #W1671 with a separately purchased cross slide vice. Its a very capable and effective combination.

George

Re: Mortising Machine. Magazine Reviews?

#4

Re: Mortising Machine. Magazine Reviews?

Scott in Montana

>Good morning Joe,

While I don't have direct experience with the Grizzly machine, I did use a Delta bench top model for years before moving up to the Powermatic floor standing model. It was my experience that the weakest part of any bench top mortiser is the fence and hold down system. I fought with it for a long time until a friend suggested that I try implementing a sliding vice to hold and adjust the material. Worked great!

So whichever brand you buy (I can say that I liked the Delta/Portercable model very much), save a few dollars to treat yourself to an after-market sliding vice.

Scott

Re: Mortising Machine. Magazine Reviews?

#5

Re: Mortising Machine. Magazine Reviews?

Chuck Kettler Greenwood IN

>Hey Ellis, these notes do not show up on my screen.

Re: Mortising Machine. Magazine Reviews?

#6

Re: Mortising Machine. Magazine Reviews?

Larry in NW Ohio

>Joe If you want mine,Harbor Freight, it`s yours just by picking it up, also if by chance you would be going to FML next month for the tour, you would go right by here. Larry in Ohio

Re: Mortising Machine. Magazine Reviews?

#7

Re: Mortising Machine. Magazine Reviews?

Joe in a Cleveland suburb

>Hi Larry.

Thanks for the offer. I think I am going to keep researching for a bit. The General and Woodtek (as reviewed in the FWW article) look nice.

What is the FML Tour?

Joe

Re: Mortising Machine. Magazine Reviews?

#8

Question about...

Joe in a Cleveland suburb

>Thanks for the responses guys. George and Scott suggested adding a vise. Can you explain that please? And how is it attached?

Thanks.

Joe

Re: Mortising Machine. Magazine Reviews?

#9

Re: Mortising Machine. Magazine Reviews?

Larry in NW Ohio

>Joe FML Stands for FRANK MILLER LUMBER. I think it was Jennifer from Indiannopolis,Ind. got it togeather for April 21. It`s about 90 miles south of me, @Union City,Ind. If you or anyone else is interested from the north, you can come down here and I`ll drive from here. Larry in Ohio

Re: Mortising Machine. Magazine Reviews?

#10

Sure Joe...

George@Colonel's Workshop-Havertown PA

>Good Afternoon Joe,

A lot of the machines rely on a fence to keep the lay out lines on the stock in alignment with the mortising chisel while the mortising operation is being performed. There is also a stock hold down devise whick prevents the stock from being raised as the chisel is withdrawn--and possibly shifting, thus putting a strain on the chisel. And, after each plunge, the stock is repositioned for the next, and that means the hold doen is also removed and reinstalled. All that can be a PITA. A cross slide vice runs about $50-$60. It is mounted at the front and slightly below the mortising machine. The vice jaws grasp the stock and allow precise chisel alignment to the lay out lines, because you canb move the stock on an x and y axis. The jaws further prevent any stock movement while the chisel is operating and is being withdrawn. Repositioning the stock for another plunge along the mortise layout is accomplished simply by cranking the appropriate x and/or y control wheel. I hope that is clearer than mud. :<)

George