Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

unisaw base

Posts

unisaw base

#1

unisaw base

David

>Last night I finished setting up my new table saw (X5 left tilt 3hp 52" Biesemeyer w/extension table). It's a bit lower than I'm used to (34 1/4") and sits on a concrete floor. Short of putting in on a mobile base which I don't think I need, does anyone have experience/recommend/recommend against mounting the saw on something to raise it up a bit, perhaps and inch or so. I'm also wondering about the base eventually rusting away from being in contact with the floor.

Thanks,

DGW

Re: unisaw base

#2

Re: unisaw base

Barry Irby

>I Added a Biesemeyer Fence to my contractors saw. The rails hung down enough to prevent me from parking my Performax under the wing. I put treated 2X6's under the feet and raised it 1 1/2" No fasteners, nothing. It just sits there. If it bothers you, you could put a screw or bolt to hold it to the the wood in each corner.

Re: unisaw base

#3

Raised mine

Charles R. Smith

>I raised my Unisaw 3 1/2 inches, using 2x4's on edge. I did so for two reasons. One was my height (6 foot 2). As well, I left a gap in the base and installed a fitting to connect another duct to my dust collector. My back and my lungs still think the base was the best modification I made to the saw.

Charles

Re: unisaw base

#4

Re: Raised mine

Ken Adams

>I once read somewhere that, the older we get, the higher we seem to want our table saws, and especially our router tables. My router currently stands at about 42".

Re: unisaw base

#5

Workbench height based on age 

Mark Goodall - ATL - tooljunkie

>


img

Re: unisaw base

#6

*BG*

Ken Adams

>

Re: unisaw base

#7

Re: Raised mine

Jay St. Peter - Southern, MD

>I raised mine 3 1/2" by using 2x4s on edge also (I'm 6'3"). I put it back into the mobile base and added a chunk of 2x12 flat on the opposite side to raise the extension legs appropriately. One of the other bonuses of doing this is I could keep my 8" jointer next to the saw without height interference from the fence adjust knob. The fact that it raises the DC fitting is the only downside I've experienced. My outfeed table shelf was difficult to position because of the interference. I wound up positioning the shelf below the fitting and have the hose running along the back part of the shelf. It would be nicer if I could've run the hose below it, but that would've made the shelf too high. It's not a big deal at all, just the only minor downside to the 'up'grade.

Jay

Re: unisaw base

#8

back saver

John K Jordan

>>I once read somewhere that, the older we get,

>the higher we seem to want our ...

Same for bathroom sinks. Too low is hard on the back. I raised the last few vanities I installed by about 4" with a frame of matching oak underneath. I raised my workbench and power tools as well. I haven't raised my lathe yet but I'm planning to.

BTW, the physical therapist's advice when at a sink/worksurface that is too low is to never bend your back but to lower your whole body by bending at the knees. Can you imagine four hours in the workshop that way?

Wouldn't it be great to have power tools and workbenches on sturdy bases that you could raise or lower at will?

JKJ

Re: unisaw base

#9

Good one Mark! LOL

Stuart Hough

>

Re: unisaw base

#10

Re: Raised mine

David

>I'm glad to hear that a number of you raised your saws. I made little blocks to raise and level my contractor's saw partly for ease of back but more to get it at the same height as a bench as CMS station that also doubled as extension and outfeed tables.

Right now I'm thinking I'll raise it about 3".

My age based workbench height would have to be pushing 50", I think. I have a 40" tall 3 year old who loves to help. Just thankful for good locks and electrical disconnects!


img

Re: unisaw base

#11

Re: Raised mine

Bart Leetch

>I raise my Unisaw 3 1/2" on a 2x4 wrapped with plywood about 1 1/2" taller than the 2x4 so I can move the saw just a little if needed without it coming of the riser. This allowed my Jointer to set on the left of the saw & my bench behind the saw & everything to work together as needed.


img

Re: unisaw base

#12

Hockey pucks!

Jim in VA

>My unisaw is raised up about 2 inches, sitting on a total of 8 hockey pucks--2 under each corner. I like the additional height. I first used hockey pucks under my lathe as a very affordable ($0.99 ea) antivibration pad. Works great. Now my lathe, tablesaw, and bandsaw all sit on 'em.

Re: unisaw base

#13

Yeah, Hockey pucks!

MN deepwoods (Dave)

>Jim, sounds great! I had a past roommate who would keep his hockey pucks in our freezer because he claimed they were faster on the ice initially. I don't recommend frozen pucks beneath shop tools. They may also move faster. Bad deal, IMOH.

DW Dave

Re: unisaw base

#14

Re: Hockey pucks!

Jim in Fenton, Michigan

>I put them under the feet of my 60 gal compressor for some vibration dampening as well. You get a really cool curly ribbon when you use a forstner bit to drill a hole in the center for the bolt to pass through..