Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

David Mark's vacuum press..

Posts

David Mark's vacuum press..

#1

David Mark's vacuum press..

Terry Alexander

>Ok...I guess I've watched nearly every episode of Woodworks with David Marks. He does a lot of veneering and thus uses his vacuum press a lot.

Do any of you have a vacuum press?

If so, did you make your own? Is it hard?

If you purchased one, or was considering purchasing one, what would you recommend?

As always....TIA

Terry Alexander

Re: David Mark's vacuum press..

#2

Re: David Mark's vacuum press.. *LINK*

Robert Henderson

>Check out joewoodworker.com for everything you ever wanted to know about vacuum veneer presses.

Also the wood whisperer had a video about making his own bags that's worth seeing


http://joewoodworker.com/

Re: David Mark's vacuum press..

#3

Pretty good article by our own Jim Shaver *LINK*

Rod Peterson -- Ormond Beach

>Right here, at WoodCentral:

Jim's article

Rod

Re: David Mark's vacuum press..

#4

Ditto

Grant Smith

>I checked out Joe Woodworker's site and built an air compressor powered vacuum press from his kit. I haven't used it yet other than to play with it. Looks like it will meet my needs just fine.

Regards,

Grant in Iowa

Re: David Mark's vacuum press..

#5

Bart Goldberg

Re: David Mark's vacuum press.. *LINK*

Bart Goldberg

>Hi Terry,

I don't know what vacuum press David Mark's has, but I purchased the basic kit from VacuPress. If you don't want to take the time to build your own, I would recommend the unit I purchased: Its the Compact 100 and I've been very happy with it.

Good Luck

Bart


VacuPress

Re: David Mark's vacuum press..

#6

Re: David Mark's vacuum press..

Tony - Memphis

>I bought one of these too. I have been real happy with it. I bought it with a large bag and then made a smaller one.

Tony

Re: David Mark's vacuum press..

#7

Re: David Mark's vacuum press..

Robert W

>Tony - how did you make your smaller bag, and where did you get the material? I have found spotty information here and there, but lost the book (read: lent to a friend) I had with detailed instructions on bag making. The bags in the instruction book were made from clear plastic upholstery protector used in furniture and sold by the yard.

But the book or similar articles can't be found. Sure would appreciate some details or some pointers.

Thanks -

Robert

Re: David Mark's vacuum press..

#8

An article about bag making

Robert W

>Well, here's one. I know this guy has been doing it for a long time but this still isn't what I was after.

Robert

Re: David Mark's vacuum press..

#9

Re: An article about bag making

Robert W

>This time with a link! *duh*

http://www.joewoodworker.com/veneering/makingbags.htm

Robert

Re: David Mark's vacuum press..

#10

Re: An article about bag making

Tony - Memphis

>That's where I got the bag making material and the glue and instructions.

Tony

Re: David Mark's vacuum press..

#11

Thanks, Tony!

Robert W

>

Re: David Mark's vacuum press..

#12

Ellis Walentine

My first vacuum setup...

Ellis Walentine

>... was a real Rube Goldberg affair, back in about 1978 or so. It wasn't even a bag, per se, but rather a sheet of upholstery vinyl that I got for a song at an upholsterer's shop. The vacuum came from a used 1/2-hp cow milker pump with about a 5 gallon tank that I picked up at a local farm auction for five bucks. I drilled a hole in the middle of my 4x8 assembly table (the top was flakeboard) for a 3/8" nipple and connected the milker to it with some 1/4" copper tubing I had salvaged from an old refrigerator. To create a seal, I used double-faced foam tape, stuck to the table around the piece I was veneering and just pressed the edge of the sheet onto it. It wasn't 100% airtight, but it worked well enough to get the job done.

My point is, if you only need a quick setup to get you through a job, you don't need to spend a lot of time or money. I'll bet you can still find those milkers around for cheap.

Ellis Walentine

Re: David Mark's vacuum press..

#13

Re: My first vacuum setup...

don at central illinois

>Man, I'm really showing my age. The only automatic milkers we had on the farm was the ones at the end of my arms! But we weren't into dairy farming, just a few milkers for us and the cats.