Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Cordless drill battery help

Posts

Cordless drill battery help

#1

Cordless drill battery help

John E

>It seems like both the NiMH batteries on my Makita cordless drill have nearly died, at about the same time. Is that usual, or too weird to be conicidence? I went to use it last night, and even when "fully" charged (green light on the charger), I can stop the chuck by hand with both of them. I have kept them in my unheated basement shop, but I'm sure they were not frozen. It probably doesn't get below the 50's down there. I brought them up to the house to warm them up and tried charging again, but no help. Any thoughts on how to revive them, or worse case scenario, I know some people have sent them off to be rebuilt - any recommendations? Tried searching the archives, but couldn't get that to work.

Thanks,

John

Re: Cordless drill battery help

#2

Re: Cordless drill battery help

Larry in NW Ohio

>John The first couple of times I had batteries rebuilt a few years ago, I just was not satisfied with the results. Then a few months ago I needed 2 more batteries rebuilt, so somehow I looked on ebay and found " voltmanbatteries" and had their 3300Ma batteries installed. I have nevre have I had a drill run so good. But of course I can not tell you how well they will last. You may want to look at their web site. Good luck Larry in Ohio

Re: Cordless drill battery help

#3

Re: Cordless drill battery help

JohnKJordan in East TN

>If you have one, a local battery store can rebuild some battery packs. We have Batteries Plus around here.

JKJ

Re: Cordless drill battery help

#4

Re: Battery builders

Mark Mandell - Gone Round In Jersey

>PrimeCell is more expensive than VoltMan for NiCads, but they use 2100+mah cells vs VM's 2000.

PrimeCell is cheaper, however, for rebuilding NiMH batteries or upgrading packs to that kind of cell.

Have friends who use PrimeCell with much satisfaction.

http://www.primecell.com

No affiliation, not even a customer (yet), so they won't know me from a post hole if you mention my name.

Re: Cordless drill battery help

#5

Re: Cordless drill battery help

Barry Irby

>I called the "local" store and they said they could rebuild them. I drove about twenty miles and carried the batteries. The guy said "OH! those are the ones we can't open." I had told them they were Makita over the phone, but the guy said he just did not think about it. So, Before you make the trip, double check.

I had mine rebuilt at PrimeCo (primeco.com). Mine are 12 volt and I had them "upgraded" from NiCad to NiMh and the largest amp hour rating they could install. Cost about fifty bucks a battery. I am fairly happy with that, but I have four batteries and I am not sure they all hold the charge as well as they should. I need to set up some sort of test to see what they are doing, but my use is sporadic and sometimes they seem great and other times I wonder. The NiMH batteries tend to trickle down over time and If I had known that, I might have stuck with the NiCad for about $36 each. I am a hobbyist and sometimes it might be a month between uses. OTOH, I have two chargers in my shop and there is nearly always a fully charged battery waiting.

There are other online services and you can buy the cells and do it yourself, if you feel comfortable doing it.

Re: Cordless drill battery help

#6

Oops!, Prime Cell, not Prime Co.

Barry Irby

>

Re: Cordless drill battery help

#7

Re: Cordless drill battery help

Bruce, a MN Galoot

>I had a similar problem with batteries on my beloved B&D Cyclone (last of the good B&D's, built 18 years ago). Both batteries, which had been rebuilt only two years before, went belly up at the same time. It turned out to be a faulty charger.

My suggestion would be to charge the batteries with a known good charger before you replace them.

Bruce

Re: Cordless drill battery help

#8

Re: Cordless drill battery help

Chicago Bob

>As a temp measure, seal your dead battery in a seal lock plastic bag and place in the freezer for approx 48 hours. Bring to room temperature and then recharge. I have done this with 12v and 14.4v PC drill batteries and they worked again for several months.I am on my 2nd freezer treatment for these batteries and they seem to have adequate power. I am sure at some point I will finally have to replace the cells. In both cases they were NiCd batteries.

I haven't come up with a theory on why this works but this was recommended by a EE that I worked with but has since moved on.

Bob

Re: Cordless drill battery help

#9

Re: Cordless drill battery help

Bill White

>I went thru the same routine late last year. Ended up buying the XRP batts from E Bay for abt $50.00 each (got two). Looked at the rebuild deals, and by the time I had shipped, bought, paid return shipping, I would have spent a bundle.

I have tried the freezer routine with no success. Could have been just me.

Bill

Re: Cordless drill battery help

#10

Re: Cordless drill battery help

Don Orr

>John,

Try www.mtobattery.com, also known as Battery Rebuilders. Very good service and pricing. I had 2 old PC 12v NiCads rebuilt by them and am very pleased. Much cheaper than new ones which I could not get anyway due to being discontinued. Supposedly they can rebuild anything.

Re: Cordless drill battery help

#11

Re: Cordless drill battery help

Larry Clinton At Frankfort (Central)., Indiana

>Sounds suspicious that both batteries would go at the exact same time and have the exact symptoms. I would first try out the drill with a known good battery and try charging the batteries on a known good charger. Surely you have some friends or relatives with a Makita. I gave away a couple of drills / batteries due to the replacement cost being almost as high as a new drill with batteries and charger. Last time I bought a Ridgid drill and Impact driver. I registered the units with Ridgid and have the lifetime "free battery replacement" service agreement. I still have one Dewalt 12Volt drill that I received from my Employer as part of a 35 year employment award. I may replace the batteries on it as it is about 6 years old. I am retired now and kind of want to keep it for old times sake.

Re: Cordless drill battery help

#12

Re: Cordless drill battery help

Barry Irby

>Larry makes a good point. Locally there is a tool repair shop and they have a tester that checks batteries. I have not seen he machine, but they take the batteries in the back and come back in few minutes with a pronouncement as to whether they are good or not. I don't think they even charge to check them. Might be worth finding such a place. (I'm near Richmond, VA. Let me know if you want the local name.)