Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

I HAD to post this

Posts

I HAD to post this

#1

I HAD to post this

Eddie Pacheco; San Jose, Ca.

>This looks unsafe just standing still...

Got this from the SF Bayarea Craigslist.

Saw Rig / Buzz Saw - $375 (santa rosa)

Reply to: see below

Date: 2008-01-23, 3:56PM PST

30" circular saw, mounted on and powered by Toyota pickup. Makes cutting firewood or scrap lumber quick and easy.


img

Re: I HAD to post this

#2

Re: I HAD to post this

Robert R Clough - Thorncraft

>I have seen rigs similar to this, powered in much the same way, over 20 years ago in Michigan (LP). I have seen them powered by a JD A or B by belt from the pulley. No matter how a buzz rig is powered, it is inherently unsafe. Nevertheless they were, and may still be common, an heavily used to cut firewood. I have used one myself. Much that was done in farming was and is unsafe - but there are "few" accidents considering that. (And I know of a few doozies that happened.)

Re: I HAD to post this

#3

Re: I HAD to post this

Pete in Holland, MI

>There are/were a lot of them around Michigan in the rural areas. We still use one at our tractor show to buzz up the slab wood from the saw mill into firewood for the steam engine.

Many were built up from parts laying around. Some were store bought. Most received their power from the PTO pulley of a tractor. Later ones mounted on a more contemporary tractor's 3-point hitch and were coupled to the rear PTO for power.

Buzz saw blades are different than saw mill blades. They have a negative rake to the teeth so the blade doesn't draw itself into the wood when cutting.

The easy ones to build were ones where a tilting table tilted the wood into the blade. The better, but more complicated designs, tilted the blade into the stationary wood.

Have seen ones like the one you show here built up on an old car/truck chassis. Often, they were built to park the vehicle, and jack up one side of the rear axle so its tire bears against a pulley on the buzz saw arbor, and let the differential shift all the power to the blade, while the other wheel was blocked in place.

Yup, they can be dangerous, but many things are when not in the hands of a confident operator. They were quite the time saving device before a chain saw came along.

Pete

Re: I HAD to post this

#4

You've never seen a portable TS? ;-)

Dan Mitchell

>

Re: I HAD to post this

#5

who writes the fine DMV or OSHA

Robin Corell in Atascadero Ca

>I think it is mounted on a truck to cause confusion. Is it under the jurisdiction of the DMV or OSHA?

Robin

Re: I HAD to post this

#6

Redneck Engineering at its best!

Chicago Bob

>

Re: I HAD to post this

#7

You've heard of SawStop

Neal in San Jose

>This is a SawGo. It doesn't stop for ANYTHING!

Re: I HAD to post this

#8

Finally, productive traffic...

Rob Hix - King George, VA

>Wow, I could use that when I have to run up to D.C. for work. When the interstate stops, I could pull out the latest project and go to it.

Thanks for posting that.

Rob Hix

Re: I HAD to post this

#9

Quick and easy; but not painless...

Jay in Tx

>

Re: I HAD to post this

#10

T-models and A-models......

Basil

>...were the favored chasis to build those on around here when I was a kid. They usually just had the hood and windshield left with a wooden box and a burlap sack to sit on. Saw a couple built on the front end of farm tractors with a belt drive off the belt pulley. They usually had a platform on hinges that you laid the 'slab' on. Then you just pushed the platform with the slab on it into the blade, back and forth, as some brave soul held the end of the short piece being cut off.

Re: I HAD to post this

#11

...doubles as a tailgating deterrent device

JohnKJordan in East TN

>

Re: I HAD to post this

#12

I'm confused......

Thomas Skaggs, Foothills of Mount Level

>....would I have to convert mileage to board footage?

Tom

PS- I'd be interested in it but it doesn't appear set up for ripping...and no miter slot either. Guess I'll keep hunting.

Re: I HAD to post this

#13

Re: T-models and A-models......

Robert R Clough - Thorncraft

>The interesting thing with these buzz rigs is that we were all very, very careful - we had to be. Well, there were those who were not careful about anything dealing with equipment - we all knew them - and the lack of hands, fingers, or arms showed it.

I'm talking of the Big Rapids area.

Re: I HAD to post this

#14

Re: I HAD to post this

Larry Clinton At Frankfort (Central)., Indiana

>Yup, I've used one powered by a tractor back in the 50's - belt drive from the tractor PTO wheel. I really didn't think it was too unsafe, didn't know any better, and much of the equipment used in industry and farms was as bad or worse. My best friend's father had a sawmill made from a 47 or 48 Oldsmobile. He cut and sawed several acres of large oak trees using it and a front loader on a tractor. I helped my friend convert a garage to a family room in his house using 2" X 12"'s X 16' air dried oak joists sawn on the Old's rig. The boards were about as accurate as I get from todays sawmill's. I didn't see the unit but my friend said it had a powered carrier/slide to move the log through the mill. Don't know how he made it, but obviously it worked quite well.

Re: I HAD to post this

#15

Yeah but,

Robin Corell in Atascadero Ca

>Just think how cool it would be to have a saw with its own radio.

Robin

Re: I HAD to post this

#16

I guess I need to travel more.

Eddie Pacheco; San Jose, Ca.

>Gee, I didn't realize that these truck mounted buzz saws were that common nor that there would be so many fond memories of using them.

The power of the internet.....

Re: I HAD to post this

#17

Re: I guess I need to travel more.

Pete in Holland, MI

>These truck mounted buzz saw rigs normally didn't do too much traveling, other than around the farm or near by farms. Twas definitely a purpose built machine with frugal engineering in mind.

Re: I HAD to post this

#18

Re: T-models and A-models......

Sonny Asburry

>I remember these also. I don't remember how they were powered,but I never saw one that the saw was pulled into the wood: they had a hinged table to push the wood into the saw.

The ones that I remembered had two safety features; A car tire (probably a truck tire) cut in two and mounted over the exposed top of the saw blade, and one had a ramp that was placed under the blade so the the cut-off fell onto it and slid away from the saw.

This was back in the '40s and '50s.

Sonny