Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

HVLP turbine system:Fuji vs, Capspray

Posts

HVLP turbine system:Fuji vs, Capspray

#1

HVLP turbine system:Fuji vs, Capspray

Randy Stukenberg

>I am looking at two hvlp turbine systems and wondered if anyone had any experience with them. One is the Fuji Q4 - 4 stage turbine, and the Capspray CT9900 - a 5 stage system. I can get the Capspray for about the same price as the Fuji (dealer wants to move it).

I will be spraying a variety of finishes, including water based laq (ML Campbell products), solvent based laq, shellac, and occasionally stain and latex paint.

Any opinions on either system?

Thanks!

Re: HVLP turbine system:Fuji vs, Capspray

#2

Re: HVLP turbine system:Fuji vs, Capspray

Brian Chitwood

>Randy,

I have had the Fuji-Q4 for a couple of years and its the only spray set up I have tried so I am not the most qualified to reply but I have had excellent results with the Fuji. Have sprayed mostly water based laquer but have sprayed one job with magna lacquer. Had good results with both. Gun is pretty easy to use and I really haven't had to make many adjustments yet. Sorry I cant compare it to the Capspray. Brian C.

Re: HVLP turbine system:Fuji vs, Capspray

#3

Re: Whole Lot Of Turbine

Mark Mandell - Gone Round In Jersey

>Randy,

A 5-stage unit is really for heavy paints and coatings; I think it's serious overkill for furniture finishing. With a discount street price over $1K, I also think you're paying a lot of money for capacity you're likely never to use. I'm not surprised the dealer wants to move it; he may be stuck with it. BTW, I've seen the Fuji Q4 for under $700, so if your dealer's down to that level, that's one helleva price!

I had a Fuji (3-stage) that I sold when I switched to a compressor /conversion gun setup. Only things I didn't like about the Fuji set were the bleeder gun and the noise; you've essentially got a spray gun hooked to the exhaust port of a high performance shop vac. If they've gone to a nonbleeder gun, it is likely that you will have increased heating of the air stream inside the turbine. I hope the gun has an insulated grip, because those guns can get uncomfortable to hold. A warm gun and air strean can be good for waterborne finishes, but can play havoc with solvent finishes like shellac and lacquer, creating flash drying and orange peel. If you go that route, be prepared to work with retarders in your finish product. I shot a lot of shellac in my Fiji with fine results, but I had to add either Solar Lux or turps to get the coating to level out properly.

I hope this helps.

mm

Re: HVLP turbine system:Fuji vs, Capspray

#4

I did a comparison article on HVLP

Michael Dresdner

>I did a comparison test article on HVLP systems in the one thousand dollar range last year for Woodworker's Journal, and it included the Fuji Q4 and the Capspray 9100, the four stage version of what you are looking at. You might want to read it. We really put them through their paces and there's some good comparitive information there.

Re: HVLP turbine system:Fuji vs, Capspray

#5

Re: Whole Lot Of Turbine

Robert W - aka nailshooter

>Wow... five stage. I have a Q4 and keep it dialed way down when shooting lacquer and primers. I don't know myself why anyone would need a 5 stage.

I was invited to a trade show (with all the the other contractors in town!) and we had a chance to shoot Apollo, Capspray, Graco, Turbinaire and Sherwyn Williams HVLP systems. They were all nice, and for fit and finish, I liked the Turbinaire the best. For parts availability, I liked the Graco the best as my local vendor can get parts very quickly.

But I went with the Fuji Q4 at the suggestion of a refinishing contractor buddy of mine. I love it. I spray exterior doors, cabinets, woodwork of any type with sealers, stains and dyes. I have a low tolerance for things that don't work, and the Fuji guys told me that if I didn't like it in under 30 days, I could send it back.

I spray a lot of lacquer with mine, and it is top shelf for that application. Like MM, I don't like bleeder guns, but Fuji is away from that and has a very well built gun with an insulated handle they put with the system these days.

Plus, when I had a question about the operation of the gun, I called the Fuji help line and talked to the owner of the company!

NO ONE ELSE had any knowledgeable staff on the phones at any other company I called. I called each of the companies I was interested in twice, and they couldn't find anyone that could give me specific information on the gun use. When I called Fuji, I talked to Paul Smith (the owner) both times.

I have been very pleased with my Fuji setup as I can take the whole machine, gun, hoses, etc. on site and have a full setup for application of any finish. I haven't had any problems with the equipment, the consumables are really affordable, and I probably made my money back on the first two - three jobs I did with this setup.

Good luck with your choice. I hope you post and let us know what you picked and what you think of it.

Robert

Re: HVLP turbine system:Fuji vs, Capspray

#6

Good deal on Capspray

Randy Stukenberg

>The only reason I was looking at the Capspray is that when I called my local dealer, he said he had one in stock. Normal price is $2200, he would sell for $900. For not much more than the Fuji, am I crazy not to get it? Also, what are the Capspray guns like?

Re: HVLP turbine system:Fuji vs, Capspray

#7

Re: Whole Lot Of Turbine

Randy Stukenberg

>WOW! Where did you see the Q4 for under $700?

Re: HVLP turbine system:Fuji vs, Capspray

#8

Re: $699  *LINK*

Mark Mandell - Gone Round In Jersey

>


Fuji

Re: HVLP turbine system:Fuji vs, Capspray

#9

Re: I did a comparison article on HVLP *LINK*

ScottS

>Wow! Their website doesn't make it easy to track down the issue with that article. Since it took some searching, I figured I'd post a link to the order page for that issue...


Woodworkers Journal, Volume 31, Issue 3

Re: HVLP turbine system:Fuji vs, Capspray

#10

Re: HVLP turbine system:Fuji vs, Capspray

Randy Stukenberg

>I ended up getting the Fuji Q4. Love it! I can actually see across my shop when I'm done spraying - no cloud of laquer in the air.

I first used it to spray on stain, worked great, much faster than a 3" foam brush. Then I sprayed everything with a water based laquer from ML Campbell. It is a new product called "Agualente" avalable in pre-cat and post-cat versions. Flowed out nice. I got a nice smooth finish the first time both for using the new sprayer and new product. I did need to thin the laquer about 20% since I was using the #3 cap set. The gun comes with a #4.

The only complaint so far is where the pressure tube from the cup connects to the gun. The attachment point is at the base of the handle where the hose connects to the gun. It gets in the way if I hold the gun in my left hand. It would be a problem if you are a lefty and hold it that way most of the time.

Otherwise, it is pretty much ready to use right out of the box. I had to play with it a bit to find the right settings for each product I was spraying, but that is to be expected. I would recommend getting the a6' flexible whip hose also.

Thanks for all the advice!

-Randy

Re: HVLP turbine system:Fuji vs, Capspray

#11

You're Welcome

Mark Mandell - Gone Round In Jersey

>Nice to hear back with positive results.

Re: HVLP turbine system:Fuji vs, Capspray

#12

Re: HVLP turbine system:Fuji vs, Capspray

Ralph Ambrosio

>What is pre-cat/post-cat. Are they finishes that are limited to spray applications? Can they be brushed on?

Re: HVLP turbine system:Fuji vs, Capspray

#13

Lacquer Flavors

Mark Mandell - Gone Round In Jersey

>Lacquer comes in several flavors:

Straight (so to speak)

"Pre-Cat" has a slow-acting catalyst (makes the film harder) added at the factory. This stuff has a reletively long shelf-life before it sets up; more popular with Clapton fans.

"Post-Cat" has a fast-acting catalyst packaged separately which is mixed by the customer after purchase and just before use (hense the "post" term). This stuff has a short pot-life and will set up in the can or the gun in times that can vary from several hours to a number of days. "Post" kind of stands for "Use it or Loose it."

|;-}

Re: HVLP turbine system:Fuji vs, Capspray

#14

Some last longer

Randy Stukenberg

>Some of the post-catalyzed finishes will last up to 6 months. I have used a product from ML Campbell, solvent based laquer, that I can't remember the name of right now. Magnalaq is the pre-cat version and I think the post-cat is magnaMax or something like that. It is a much harde, more durable finish. They also have a water-base called agualente that is available in both pre- and post-cat with a longer shelf life. These are all spraying laquers. The Deft you most often see in stores is a brush on. There are even post-cat urethanes.

I think most of the higher end post cat finishes will have a pretty short shelf life (hours or maybe couple of days).

-Randy