Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Need a Dowel

Posts

Need a Dowel

#1

Need a Dowel

Larry in NW Ohio

>In building the new Bed for the new arrival I am going to need a 2"x5' Dowel rod in oak. I found a place somewhere in Mich. four years ago for the other bed, but like it usually goes I can`t find them again. I googled untill I couldn`t google anymore. I know someone from the vast information of WC knowledge, someone will know. Thanks to Everyone that has ever helped me. Larry in Ohio

Re: Need a Dowel

#2

Re: Need a Dowel

steve mackay

>The best I've found for oak that big is The BORG. Thing is . . . you can't ask for dowel. You gotta ask for stair banister. If you ask the lumber guy you'll get a blank stair ( sic ).

Re: Need a Dowel

#3

Re: Need a Dowel

JohnKJordan in East TN

>If you can't find one, there are people with lathes that long that could turn one - you could ask on the Turning forum here.

JKJ

Re: Need a Dowel

#4

Re: Need a Dowel

Ray Binnicker

>Hey Larry,

Excelldowel.com say they can provide anything up to 3" x 12'.

Ray

Re: Need a Dowel

#5

WHEW! Glad it's not Quarter sawn Oak!

Ron Hildreth

>

Re: Need a Dowel

#6

Re: Need a Dowel

Barry Irby

>Could you make one? A friend wanted me to turn one. Then he told me he was going to cut a notch out or one side and glue in a board. That is, he was going to end up with a three fourths of a dowel glued to a flat piece. I suggested he use a round over bit and make three passes. Worked for him. Or if you need it round, you could make four passes.

Re: Need a Dowel

#7

Re: Need a Dowel

Larry in NW Ohio

>Barry Nice suggestion, I`ll look into that and the excel place. Oh and Barry all this time I just thought you were just another pretty face. Thanks. Larry in Ohio

Re: Need a Dowel

#8

Just turn it 90 degrees ;)

John in New Mexico

>

Re: Need a Dowel

#9

YUKKKK!!!!!

Geary from NJ

>

Re: Need a Dowel

#10

Hey!!! I resemble that Remark!!!

Barry Irby

>While I have never been mistaken for a pretty face, I look pretty good for a guy twice my age.

Re: Need a Dowel

#11

Make your own

Lee Schierer - McKean, PA

>It is really easy to make your own dowels on a router table in four passses. All you need is a table mounted router, a router bit with the proper radius and good fence and a feather board to hold the wood against the fence at all times. Set the router bit so the top edge and bottom edge are flush with the fence and table. Place the feather board so it will hold the wood tight to the fence. Cut a piece of wood the length or slightly longer than you will need. This piece of wood should be exactly square and the same dimension as the diameter of the finished dowel you want.

Then feed the wood through the cutter. Rotate the piece so the area you just cut is now up and agianst the fence. Make the second pass. Rotate the stock the same direction again, always keeping the flat side on the table and the corner to be rounded down and toward the fence. On the final pass you will have one square corner left and you will be cutting that away as you push it through the bit. Be careful on the last few inches as the piece may tend to rotate as you push the last of it through.

Use a push stick for all passes. Make all the cuts full cuts to the finished dimension this is one time you can't sneak up on the finished size so watch the grain direction when you start to avoid tearout.

Some people like to leave 3-6" of square stock on one or both ends to prevent rotation of the piece during the cuts, I've found that this isn't necessary, but if it suits you do it.

Lee