Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Sharpening question?

Posts

Sharpening question?

#1

Sharpening question?

Barry Irby

>There seems to be a spectrum of sharpening opinions here. Some people throw away small dull drill bits and buy new ones. Some buy a Drill Doctor and some learn to sharpen them on a grinder. Some people sharpen a chisel on a grinder and if it's lucky give it a pass or two on a stone of some description. Some buy water stones or pieces of granite milled flat (very flat). I'm trying to sort this out. I am largely self taught and have little experience outside my own shop. Some of the sharpening advice makes sense to me and some of it seems over the top, with some of it being "under the bottom" if I may coin a phrase for the opposite of "over the top".

I want to figure out what the "Cut off point" is. I want to work wood reasonably efficiently, not devote my life to sharpening to the point the tools never touch wood. Unless there is something to be gained I don't want to get into the moment of Zen between me and the stones.

Also, I don't have a lot of money to invest. I guess what I am looking for is the "Dummies Guide to Sharpening". Does anyone have or know of such a thing?

Also, what have you tried that worked for you and continues to work for you. What are your "go to" sharpening methods. Not the fad of the moment but what you actually use.

I'm thinking of plane irons, chisels, card scrapers, Drill bits, or all those things you need to sharpen. Is there a common thread?

Re: Sharpening question?

#2

Re: Sharpening question?

Clint Searl, at the base of Haycock Mtn

>Barry, you're not supposed to raise religious questions on WC.

The answer is: "Whatever works for you."

Clint

Re: Sharpening question?

#3

Re: Sharpening question?

Lee Ohmart

>I had purchased a device to hold drill bits against grinding wheels to sharpen them but, for the life of me, could never get a good result. I bought the Drill Doctor and that solved the problem. For chisels, planes and other flat edges, the method of using wet/dry sandpaper on a flat surface (in my case a section of granite tile) is inexpensive and prduces awesome results. I have been able to produce edges that truly are "scary sharp." I'm not a turner so I have no idea how those artisans sharpen curved surfaces. For knives, I still use oil or whet stones followed by application of a steel and stropping on an old belt. There may be better ways but this is just the way I was taught in Boy Scouts and it's become a habit. My axes and splitting mauls get a shrpening using a mill bastard file followed by a medium whet stone while the scythe only gets stoning to keep it sharp. Admittedly, that's a lot of different methods. I suppose because different edges are made with different materials, are ground to different edges and have different applications.

Re: Sharpening question?

#4

Re: Sharpening question?

Mike Fitterling

>I have tried just about every combvination of sharpening techniques. I rather enjoy sharpening, so I have collected all sort of devices to help like a horizontal wet grinder, and regular dry grinder, oil stones, diamond stones, files, jigs, etc.

I still mess with various bits and pieces, but if I just need to get a quick and sharp edge while working on a project what has worked for me is a primary grind on a friable high grit wide white wheel on the ole Delta dry grinder, dipping in water often to avoid losing temper. I take very light passes I use that in combination with a Veritas tool rest.

From there I just use wet and dry sandpapers up to 1 micron usualy in this sequence: 400, 600 1200 15 m, 1 m. Once the main grinding is done correctly, doing the sandpaper (Scary Sharp) is quick and easy. It helps to have a guide like the newest Veritas honing guide, but others will do the job too. I have used different stuff for under the paper and I don't think ti makes a lot of difference as long as it is flat. I used marble tiles from Homedepot for a long time but now use some granite counter cutoffs that were given me. I like the granite because it is heavy enough to stay put and large enough I can put all the paper down on it at the same time. Spritz the surface with water, stick the paper down, spritz the working surface of the paper and go to town.

If there are no nicks on the edge and the tool is just dull, I forego the dry grinder and just do the sandpaper steps. It only takes several swipes on each grit and you are done. I watch to see the scratch marks from the previous paper go away and be replaced by new finer ones, then a swipe or two on the flat back of the cutter, then on to the next paper. I can hone from dull to sharp in probably two minutes on a typical plane iron.

Cheers,

Mike

Re: Sharpening question?

#5

Re: Sharpening question?

jeff

>Barry

You are in persuit of the holy grail.

There are so many different ways to end up with a sharp tool, and every expert has their own opinion.

I think I've tried them all (or at least most) and have settled on what seems to work for me most of the time.

I have a huge pile of gadgets and usually use what's expediant at the time.

When I was in business years ago, I used to buy drill bits by the package. When one got dull, I threw it away. I only touched up the expensive larger ones. Fast, quick and cheap.

I still have a drill doctor, bit sharpening jigs (at least 4 types), and what-ever that are never used. Just use a grinder and my eye.

Time was money then.

Now I can take my time sharpening a chisel, plane or whatever.

Don't get hung up on things, experiment and use what you feel comfortable with.

Jeff

Re: Sharpening question?

#6

Re: Sharpening question?

Tony - Memphis

>I took a class once that used Norton water stones. I fel in love with them and came home and ordered the set. I think Tools for Working Wood had the best deal at the time. I was surprised at how sharp my irons and chisels got with minimal effort. I flatten them with sandpaper on glass once in a while and keep them in water (containers from the $ store). I use a Veritas jig most of the time, but I do a lot by hand too. I tried the sandpaper, but I like the Norton's better. I strop on a piece of MDF charged with the green crayon from Lee Valley or the yellow stuff (?). I'm not a sharp freak by any stretch and all my tools are used! So there's my two cents. Oh, for carving tools, I use oil stones because the don't wear like the water stones. And, I confess that I own a Tormek. I use it mostly for shaping and for turning tools. I rarely use the edge right off the Tormek. Good luck with your sharpening. The tough thing is you have to try each method to see if you like it!

Tony

Re: Sharpening question?

#7

Re: Sharpening question?

Bill Schreiber, Litchfield, NH

>I think what is important is to pick something and stick to it. They all work. You can also build your own sharpening system too; I think you missed that.

For me, router bits and drill bits in the trash when dull. Veritas honing guide, wet dry sandpaper and a granite plate for chisels and plane irons. I know people can get "scary sharp" plane irons in 5 minutes, but it takes me 20 minutes.

good luck and merry turkey day.

Regards,

Bill

Re: Sharpening question?

#8

JL

Re: Sharpening question?

JL

>I use multiple sharpening methods.

An 8" grinder for my turning tools with a 100 grit wheel.

A set of water stones for my chisels, plane blades, spokeshaves and drawknives (also for card scrapers).

Sand paper and a dowel for my concave tools.

My Tormek only gets used for my planer and jointer blades now.

Drill bits - I touch up my Forstner bits, auger bits and my brad points with a little diamond hone. I've got a Drill Doctor for my other bits if they ever get dull - but I inherited it - I didn't buy it.

Re: Sharpening question?

#9

Re: Sharpening question?

John E

>Barry, I've wondered exactly the same thing. Last year, I took my first (and only) woodworking class. It was at the Dogwood Institute near Atlanta. My wife gave it to me as a gift. Well, one of the basics of the class was sharpening and tuning planes and chisels. "Rather dull", I thought (no pun intended.) Well, turns out it was quite an education, and very enjoyable. It was the first time I have ever been able to take a $50 plane and make a shaving you could see through! They used a slow grinder and waterstones, so I guess that's my preferred method (and the only one I know how to do.) I guess the point of all this is you might consider taking a class that involves sharpening. Might save you LOTS of heartache and trial-and-error.

My 2 cents.

John

Re: Sharpening question?

#10

Is it a rite of passage that means anything today?

Chris Knob

>I learned how to, by several different passionately endorsed methodologies, get a plane iron sharp enough to shave the hairs on my arm. The sad fact is that I found in several years of woodworking for profit and pleasure, I used these hand tools little. Yes, I know the virtues of using a Bedrock smoother to hand plane a surface and give it that hand worked look and the satisfaction that comes with joining an edge well but...I have a drum sander and a mechanical joiner that do the job much faster and frankly, better, so most of my razor sharp hand tools sat under the work bench for very occasional use. Yeah, the block plane helps me fit a drawer and a few other things but as passionate as I was about collecting high quality hand tools, I ended up selling almost all of them out of practicality.

Re: Sharpening question?

#11

Re: Sharpening question?

Ron Hildreth

>Good Morning, Barry

I've spent a lot of money, buying different sharping systems/tools. My FIL had a sharpening shop that I used to keep him busy, but since his death three years ago, I've had to do a lot of experimenting to find what works best for me and what I'm trying to sharpen at the time. BTW- three years is not enough time to become good at anything I've tried, but I've been able to narrow it down to a few.

Power sharpening - After reading Garrett's review of the Worksharp 3000, and not real happy with my bench grinder, I bought the Worksharp. Best money I've spent so far for sharpening my plane irons, chisels, even lathe tools and my pocket knife. It's a keeper! Oh yea, thanks Garrett, for a very good review ! Certainly helped me greatly!

Hand or Manuel sharpening - I'd have to say the scary sharp system is the best for me, especially for touch ups on chisels. I supplement this by using Lee Valley's Veritas MKIII guide. As for my card scrapers, I found that Rocklers card scraper sharpening jig w/bastard file and burnisher works best.

My mileage may differ from others!

Ron in Iowa

Re: Sharpening question?

#12

Re: Sharpening question?

Jay St. Peter - Southern, MD

>Unfortunately, sharpening is a necessity and requires some investment of time and money. The least expensive way to go is sandpaper on glass. I got a fairly decent sized piece of glass from a glass place for free (a cutoff). It has sharp edges, but is still flat.

I've tried a bunch of jigs, but the new Veritas works best for me. It takes some time to initially get everything sharp with your jigs/methods, but once it's done it doesn't take much to keep them reasonably sharp. Then as time and money allow you can investigate different methods.

I have a Drill Dr., but don't consider it a necessity. It is nice to just be able to sharpen a bit when it gets dull instead of having to remember to stop off and buy replacements ... and remember which sizes ... and wind up chipping or burning holes instead of drilling them when you forget and continue to use the dull bits. But, definitely just a nice to have. I think getting plane irons, chisels, etc sharp is more important. Not to mention safer.

Jay

Re: Sharpening question?

#13

Re: Sharpening question?

NickB

>I have very little time in the shop (full time job, plus three small kids), so speed is of the essence for me (so little time in the shop, I hate to spend it sharpening, making jigs, or doing much of anything that doesn't involve actual woodworking). I have the Lee Valley motorized sharpener, which I quite like because it is fast-jig to get the blade set right, and it takes only a couple of minutes to work up through the grits, then finish off with a strop charged with green compound. The Lee Valley sharpener doesn't get my tools any sharper than I can with stones, but it is much faster and cleaner, so I sharpen more often.

Nick

Re: Sharpening question?

#14

Re: My Humble Opinion (very long)

Larry Clinton

>"I want to figure out what the "Cut off point" is. I want to work wood reasonably efficiently, not devote my life to sharpening to the point the tools never touch wood. Unless there is something to be gained I don't want to get into the moment of Zen between me and the stones."

First - congratulations, you have already came to the right decision as to the amount of sharpening required. I have heard some people that think a chisel or plane can't be used unless they can get a very close shave with it. I do not find this at all necessary for most (if any) woodworking tasks.

First, the only thing you are trying to do is to remove material from the tool to bring two adjacent sides to an invisible point. A few years ago (ok, about 55 years), I watched a good craftsman working on our home sharpen his chisel on the concrete step then finish it on an Arkansaw stone. Guess no one had told him he needed waterstone's, grinders, or special tools. He did this in less than 5 minutes and the tool worked very well. I am an old FaXX, and have tried just about every method (Scary sharp, waterstone's, oilstone's and the concrete step). Guess what? All of them work pretty well. Some are faster, some messier, some more expensive, some take longer, but all work. Also it depends on what your going to do with the tool. I have a set of LN chisels I use for paring only. I do keep those very sharp as the surface I am paring often affects the appearance of the item I am building. If I am just roughing out a hole I may use a chisel right off the grinder.

"There seems to be a spectrum of sharpening opinions here. Some people throw away small dull drill bits and buy new ones. Some buy a Drill Doctor and some learn to sharpen them on a grinder."

I do a little of all three, I have an old B&D drill sharpener (bought at an auction for about $10), I do use it on some small bits (can't see quite as well as I used to). Unless they just wanted the tool I doubt a woodworker could really justify the cost of the drill doctor. You don't need the high quality bits to drill wood, and you can buy several sets of bits for the cost of a drill doctor. larger bits I will often hand grind. Some smaller bits I toss. (I go to a lot of auctions and have a real large supply of bits). Try hand grinding some of your dull bits and see what your results are - what do you have to lose? Look at some new bits and try to match the profile and relief areas. If you want to take the time to learn proper grinding look around your area for some old machinists or tool makers. Many are more than happy to show off their skills and teach someone. One warning, the wheels that are furnished with most bench grinders are really not suited for sharpening tools. They are sold with very hard wheels that generate a lot of heat on the tool. Several places (Lee Valley is one) sell softer, courser wheels that make it a lot easier to sharpen without overheating the tool. It takes a light touch and a little time to sharpen, don't push a drill bit or chisel into the wheel expecting to grind it to shape in 5 - 10 seconds, you will, but it will get hot enough to remove all the temper and will only be good to make more holes in or shape swiss cheese. I keep a container of water near the grinder and try to never get the tool hotter than I can hold comfortably (at the cutting edge).

Some people sharpen a chisel on a grinder and if it's lucky give it a pass or two on a stone of some description. Some buy water stones or pieces of granite milled flat (very flat). I'm trying to sort this out. I am largely self taught and have little experience outside my own shop. Some of the sharpening advice makes sense to me and some of it seems over the top, with some of it being "under the bottom" if I may coin a phrase for the opposite of "over the top".

My findings on Water Stones vs Oil stones vs scary sharp. I have a good set of all three (not necessary but I have reached the time in my life I can afford it).

(A) Water stones have some advantages - They break down easily, this exposes a "new" surface constantly while you sharpen. This makes them remove material quicker than an oil stone. The disadvantages are that 1) This "break down" removes grit from the stone making them less than flat. This requires that you flatten the stone often to keep a straight edge on your tools. The second issue is that the many water stones must be "soaked" prior to use and must be used with water while sharpening, this takes time and is a problem if the shop is unheated - freezing a soaked water stone may break it into little pieces. The water stones are messy as I get the slurry (water mixed with grit)all over the place. I really end up with a mess after I have sharpened a few tools. Another disadvantage is that the tool is wet after sharpening and must be cleaned, dried and (I personally either oil or wax the tool to prevent rust). Initial cost of the stones, container, flattening stone etc. is fairly high ($150 ~ $250 or more for a reasonably good set). Also waterstones wear somewhat rapidly so you may have to replace them in a few years.

(B) Oil Stones: These were used for many centuries, and can provide exactly the same results as water stones. The advantages are that the oilstones are hard and stay flat much better. A set should last your lifetime. (You can flatten worn ones with a diamond stone or abrasive powder on glass). The tool, after sharpening is coated with oil and just requires wiping with a rag before use. The oil will help prevent later rust. The disadvantages are 1) The oil is kind of messy (although IMHO much less so than the Waterstone method)and 2) the stones are quite hard so cut quite a bit slower than the other methods. Again the initial cost is fairly high ($150 up to $250 or more.) I have a ceramic ultrafine stone I use after the oil stones to shine the back of the tool and use it to put a "mico bevel" on the edge.

Scary Sharp: I used this method for a year or so. I didn't purchase a piece of ultra flat granite however. I purchased a few pieced of scrap 1/4" thick plate glass from a local glass shop. (cost around $.50 a piece). IMHO this is plenty flat for this application and having extra pieces allowed me to attach more grits to the glass. This is a pretty good method of sharpening on a budget (actually as good as the oil or water stones) and initial cost for me was between $20 and $50). I used the 3M spray adhesive to stick the sandpaper to the glass - I think I used acetone to remove / replace sheets as I remember. You can use wet dry Emery paper available at the local auto parts store. If you desire a "high shine" to the tools you can get grits that will do this. The abrasives stay "flat" if properly adhered. I did have some problems flatting the back of blades if I used the "cloth backed" abrasive (I think it "gives" and abrades material - not an issue with the "paper" backed abrasive. Really no big disadvantage to the method except you have to keep buying abrasives, and it is messy to remove the adhesive and replace the sheets. If I were just starting out I would use this method.

"Also, I don't have a lot of money to invest. I guess what I am looking for is the "Dummies Guide to Sharpening". Does anyone have or know of such a thing?"

Although I do not own it, many have recommended Lee Valleys "The Complete Guide to Sharpening" by Leonard Lee. It is available on VHS or DVD (around $15 to $22)

Also, what have you tried that worked for you and continues to work for you. What are your "go to" sharpening methods. Not the fad of the moment but what you actually use.

I actually currently use several methods dependent on the tool issues. If I am sharpening my paring chisels or plane blades, I normally use the oil stone method as I don't need to remove much material, just touch up the edge. Sometimes all I need to do is hit the "micro bevel" using my ceramic stone. If the tool requires a lot of material to be removed due to a small chip etc., or I really have to flatten the back I will set up the water stones - normally I wait until I have several tools to sharpen, as this makes such a mess and I have to soak the stones. If I have really damaged the edge I will regrind it on either the bench grinder with a "cool wheel" or use my surface grinder (no, you probably don't want or need one of these).

As an addendum, I did use the Scary Sharp method for over a year and obtained excellent results. I just got tired of buying abrasive paper and messing with replacing the sheets. T

I'm thinking of plane irons, chisels, card scrapers, Drill bits, or all those things you need to sharpen. Is there a common thread?

Not really, Plane Irons and chisels are similar, I would recommend a beginner purchase a Veritas MK 2 honing guide ($60). This can be used to sharpen all your chisels and plane blades using any of the sharpening methods. It will allow you to hold the same angle on your tools and makes learning a whole lot easier. As you gain experience, you probably will learn to "hand hold" many tools and sharpen without the jig. I still use it for narrow chisels and plane Irons as I find it saves me a lot of time. It allows you to Micro bevel the edge without effort. Card scrapers are a different bird. I have tried many methods. I currently use a file and homemade jig to square / clean up the edge, then use the edge of my oilstone to hone it. I have the Veritas burnisher (used to put the "hook" on the edge) and scraper holder. Drill bit sharpening was discussed above.

One of the most common errors in sharpening chisels and plane blades is not completely flatening the back first. This is one of the two surfaces required to make the edge and is the very first and IMHO most important steps. I normally spend several minutes on a new tool getting this edge flat and polished. (You only need to have the last 1/16 to 1/8" of the surface perfectly flat). Once a tool is properly shaped and sharpened (barring a chip), I normally can resharpen the edge in 2 or 3 minutes to a usable state.

Re: Sharpening question?

#15

Re: My Humble Opinion (very long)

Chris Knob

>For a while. I thought being a "real" woodworker meant having a slew of hand planes of every number and sets of chisels and card scrapers all at the ready to demonstrate my proficiency at producing gossimer curls of figured maple etc...Ive done Scary Sharp, diamond stones, wetstones, powered systems..

Today, 95%+ of my chisel work is done by two Marples chisels of 1/2" and 1 1/2" width...all of my hand plane work is done with a rabeting block plane and I haven't burned my thumbs with a scraper in years. I tried "real woodworkers" out there... but when 5 passes through the drum sander in less than 10 minutes does what 45 minutes with a variety of hand planes and scrapers do...and better. (I've tried to explain to one too many customers that they need to accept surface variations and tear out as the hallmarks of fine hand work!)...it's a no brainer.

Nice to know if I ever have to shave my arms...I can alway do so!

Re: Sharpening question?

#16

I have been using sandpaper for so long I can ..

Art Silva

>remember that the biggest problem we had was finding a glue that would hold the ground granite to the Mammoth hide long enough to get a good edge. That's when we coined the name "Scary Sharp".

Re: Sharpening question?

#17

drill bits

john lucas

>Barry I have been sharpening drill bits by hand and then with an older jig and lately with the Drill Doctor. Bits under about 3/16 i just toss. I don't like the point that the drill doctor puts on bits this size. Anything bigger the drill doctor does Ok althought I still prefer a different point. It puts a good edge on and it cuts it's just harder to feed than a new drill. For woodworking you won't notice the difference but when cutting hard steel it's pretty noticeable.

Re: Sharpening question?

#18

Re: Sharpening question?

Carol - now in NC Nebraska

>Short answer, Barry.

Scary Sharp for flat stuff - I use 3/8" CAST Plexiglass, 3M Adhesive, 120, 220, 400, 600 grit SC paper dry or the occasional spritz. Peel off with a razor blade and reglue a new piece.

Buy new drill bits. - I have an old Drill Doctor and use it in a pinch and on the larger more expensive bits.

Toss dull router bits and re-purchase.

Saw blades - send them to Scott's Sharpening

Turning tools - 8" HS grinder with white wheels from LV

Kitchen knives and scissors - butcher's steel

Carving - different rouges and shaped wood or MDF

Have the Leonard Lee Book - was very helpful.

I have other sharpening tools but this is what I use.

My 20-20 hindsight and my level of tolerance. YMMV.

So what did you want to sharpen?

Re: Sharpening question?

#19

My 2 cents!

Lee Schierer - McKean, PA

>I had hand tools in my shop that rarely got used because they were dull and didn't work well. At a 5 Barns gathering I aquired a piece of 3/8 or 1/2" plate glass and decided to try the scary sharp method. I think my total investment in material was less than $50 and in a short while, I sharpened a plane iron so I could see my reflection in the bevel and the back side. WOW, what a difference. I spent most of a Saturday sharpening everything in the shop with a cutting edge. Hand tools now play an important role in nearly every project.

If your budget allows the more expensive systems and you are so inclined by all means get them, but as others have said you can get very acceptable results with a floor tile and wet/dry sandpaper.

Lee

Re: Sharpening question?

#20

Re: I have been using sandpaper for so long I can

Clint Searl, at the base of Haycock Mtn

>Art, there's a great article on sandpaper in the current issue of "Woodchoppers (ne Woodshop) News", but it doesn't reference Mammoth hide or flint chips from when you made your own arrowheads.

Have a good T-day

Clint

Re: Sharpening question?

#21

Re: drill bits

MikeW

>Hi John,

Because I use small (<3/16) solid carbide drill bits to drill hard spring steel, I got in the habit of using a Drill Doctor--easy to snap a 5/64" solid carbide bit on a grinder if one isn't really careful!

Now I use the DD for them all. Newish habit I suppose (or laziness).

The issue about the point. I would disagree about the point. Set to the blunter option (I forget the angle) we put on a better point/edge than they come with. Same with less-hard bits. And we do drill hard steel (up to 58 RC). Perhaps my machine was built on a Wednesday? [g]

Take care, Mike

Re: Sharpening question?

#22

Re: Sharpening question?

Doug Ridley

>Barry, Google up Work Sharp 3000 and look at the video. For what you are talking about it is absolutely the quickest and best way to get perfect edges in just minutes.

Re: Sharpening question?

#23

Re: Sharpening question?

MikeW

>"I'm thinking of plane irons, chisels, card scrapers, Drill bits, or all those things you need to sharpen. Is there a common thread?"

Hi Barry.

Not intending to be flip, but what is it you do now for each of those things? Does it work? Are you satisfied?

There never will be a common "thread" to sharpening. "Impossible" comes to mind. Unless you are simply bored with what you are using, or have the feeling that you need certain edges to be sharper, just keep on doing what it is you are doing for sharpening and keep making stuff. Any other option if not needed or wanted is just more expense.

Take care, Mike

Re: Sharpening question?

#24

Re: Sharpening question?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Barry,

I get bored sharpening and try to avoid it. I do sharpen chisels for my #3 son's business. It costs his carpenters a case of Sam Adams each to hone a set of their Stanleys or Marples. I use a DMT diamond impregnated stone to insure the chisels are flat. Them I use a Grizzly 70 rpm wet wheel with Accu-set jigs and make an additionjal pass or two on the stone for the microbevel. Then I use a polishing head and hard cotten wheel with compound to get a mirror shine. No trouble shaving the hair off your arm.

George

Re: Sharpening question?

#25

Re: Sharpening question?Here's the $425 Solution.

Garrett in Victoria

>Hi Barry

I have just about all the sharpening gizmos except Lee Valley's platen.

For chisels and plane irons, the one I reach for is the Worksharp. It's Scary Sharp but mechanized. Fast, effortless, clean, and good. At ~$200, it's cheaper than a set of waterstones, too. (See my review in WC Articles and Reviews.)

For scrapers, you require only a good file and something round that's harder than the scraper to turn the burr. You can use the shank of a cobalt drill bit or buy a tool for $10. (See the new article on sharpening scrapers in WC's Articles and Reviews.)

For drill bits, it's the Drill Dr. I've also pretty much discarded my HSS drill bits after 'investing' $75 in a full set of cobalt split point bits. They last many times longer than HSS bits and the Drill Dr . - about $100 on sale - re-sharpens them effortlessly.

I sharpen turning tools on a $50 bench grinder with an aluminum oxide wheel and a home-made jig. (The carborundum wheels work just as well, but require more care to avoid overheating.)

Total cost of the above including set of 29 cobalt drills: ~$450.

And finally, when none of the above will do the job, I pull out the truly expensive Tormek which is an amazing system that will do just about any edge on any tool, but for which the cost is setup time.

Cheers, Garrett