Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

What's going on with my table saw?

Posts

What's going on with my table saw?

#1

What's going on with my table saw?

Warren E. White

>I have a Delta Cabinet Saw, not too old, but of course out of warranty. Everything was working just fine yesterday when I was cutting some picture frames.

Today, when I turned the saw on (or tried to) it made a horrible bumping sound, and the blade started up; stopped; started; stopped. Never got up to speed. I noticed the blade was hitting my zero clearance slot just slightly.

I unplugged the saw, felt the blade and it seemed tight. Plugged back in and tried to start it up. Blade wasn't tight obviously, because the arbor nut came off. I assume because of the vibration caused by the shaking going on. I shut down with no damage done to me or the blade.

Put the arbor nut on again, very tight. Inspected the three drive belts from the top and all looked OK. Turned the blade by hand (with the saw unplugged) and it turned free. Started it up with the zero clearance insert off. Bumped a few times and then came up to speed. Tried to shut if off with the switch and it just kept running. I unplugged the saw. Plugged it back in and it is still running. Off switch has no effect.

What the heck is going on?

Thanks for any insight you might have.

Warren

Re: What's going on with my table saw?

#2

Re: Ghosts ?

Chuck Lenz

>

Re: What's going on with my table saw?

#3

Dale Lenz

Re: What's going on with my table saw?

Dale Lenz

>I'd start checking the switch out, use ohm meter if you have one and know how to use it. I've had at least two table saw switches go out on me in the 25 years or so of owning my TS. I believe I've had similar symptoms as yours, with the exception of the lose blade.

Good luck...Dale

Re: What's going on with my table saw?

#4

Re: What's going on with my table saw?

Warren E. White

>Thanks Dale. I have one, and as an ex-electronicker I should be able to figure it out. I go back to vibrators in car radios, 5U4 rectifiers in TVs, convergence adjustments and degaussing coils in the first color TVs. Dang....I just figured out I am really old!

Warren

Re: What's going on with my table saw?

#5

Re: What's going on with my table saw?

Bill White

>Always thought that it would be cool to put the degausser around your head. Think it would mess up the old brain waves? I also remember the old #40 tubes. Fleming valves eh?

Bill

Re: What's going on with my table saw?

#6

Re: What's going on with my table saw?

Rob Stokes in North Vancouver

>Warren - I'd start by putting the saw together, making sure it's all tight, remove the insert and fire the saw. Still make the noise? Remove the blade and fire it again. Still make the noise? Remove one belt and try it, then two belts and try it, then all belts and try it. You get the idea.

At some point it will either stop making noise or it won't. If it stops, the cuplrit is the last part you took out of the equation. If it doesn't, you're down to your motor.

Rob

Re: What's going on with my table saw?

#7

Dale Lenz

Re: By no means....

Dale Lenz

>did I try to be disrepectful of your knowledge. I recall that my sentence over the ohm meter Could be read wrong.

Sounds like you could walk circles around me with your elect. knowledge. What's a vibrating radio, telling me age, 52 model.

Re: What's going on with my table saw?

#8

Re: By no means....

Warren E. White

>No disrespect intended, and certainly none taken. Good suggestion which I will get to this morning. Wish me luck!

Warren

Re: What's going on with my table saw?

#9

Re: What's going on with my table saw?

Warren E. White

>Rob,

The problem right now is that it won't turn off with the switch. I think it must have been something to do with that (I am going to check that today). Perhaps only one leg of the 220 getting to the motor; switch failed in the "OK, I will turn on, but I won't turn off" mode.

I appreciate everyone's thoughts, and I will let you know if I have any success.

Warren

Re: What's going on with my table saw?

#10

Re: By no means....

Chuck Lenz

>Dale, I'm just guessing, but I think he means the old tube radios.

Re: What's going on with my table saw?

#11

Dale Lenz

Re: Thanks, cuz, : ' >...

Dale Lenz

>I do remember them. Took a while to "warm-up".

Re: What's going on with my table saw?

#12

Re: What's going on with my table saw?

Larry in NW Ohio

>Warren Since the motor will not turn off the first thingI would look at is the switch. If it has points in it then the points may be carboned up and sticking together. I`d start looking at the switch real close. Good Luck Larry in Ohio

Re: What's going on with my table saw?

#13

Re: By no means....

Dan Donaldson

>Tubes require higher voltages than 12 volts to work. In the old car radios, they had a unit called a vibrator that was basically a relay that was set up to open and close its coil itself, which meant it buzzed. The thing was in a can to dampen the noise, so if you touched it when it was running, it vibrated, hence the name. It's purpose was to chop up the DC of the car battery into a pseudo AC that could be put through a transformer to create the higher voltages required by the tubes. It was kind of a neat idea and was an inexpensive way to get what was needed. The same thing would be done electronically today rather than electromechanically.

Re: What's going on with my table saw?

#14

Gotta wonder why that arbor nut came off...

Tim Greif - West of Chicago

>That's a very strange thing to happen on a saw. Arbor nuts are always threaded in reverse direction of blade rotation. Result is that they are self tightening. I can't see how it could come off unless the saw is running in reverse direction. Is that possible?

Re: What's going on with my table saw?

#15

Re: Gotta wonder why that arbor nut came off...

Warren E. White

>My guess is that the arbor nut came off because of the excessive jarring that was happening at the time. The saw wasn't turning in the wrong direction, but it was having some sort of convulsions.

I called Delta this morning, and they suggested bypassing the switch and see if it worked. They said it was just a test, and DON'T TRY USING THAT WAY! (Makes you wonder why they felt it was necessary to say that. I always want a big blade turning and have to turn it off by running across the garage to pull the plug. ;) ) Since the switch has already bypassed itself, I ordered a new one. $180.09.

Thanks for all of the help. I'll post a follow-up.

Warren

Re: What's going on with my table saw?

#16

One thing to be careful about

Derek

>If the switch blew because of another problem (thinking motor draw here), it is possible the the new switch may get fried as well.

I could not quite understand what you did try. If you did not try bypassing the switch completely and making sure that it runs normally, I suggest you try it.

I would also check the motor after running the saw for a bit with no cutting load. It should not be too hot. If the motor is really hot, it may have some partially shorted windings and that could have killed the switch.

It could be that the switch died because of heat - Summer weather is hard on electronics and electrical stuff.

Re: What's going on with my table saw?

#17

Re: Gotta wonder why that arbor nut came off...

Barry Irby

>I have an old chop saw that stops the blade "instantly". As I recall, it does that by "throwing a DC pulse" through the motor". (Don't ask me for a better explanation, I just looked at the pictures and turned the pages.) If you install the blade and don't snug it up really well, the stop is so violent, it will loosen the arbor nut. The blade will freewheel after that. Wonder if it is possible that something like that happened to your saw motor when the switch failed?

Two other logical explanations are "you forgot to tighten it" and magic. There is a certain amount of magic in my shop.

Re: What's going on with my table saw?

#18

Re: One thing to be careful about

Warren E. White

>I appreciate the suggestion that something might have caused the switch to fry. The switch is almost certainly bad.

As for what I did to bypass the switch, basically I did nothing. I tried the switch one last time and the saw came on as normal. However, when I tried to turn it off it wouldn't turn off with the switch. I disconnected the power cord. When I reconnected it, the saw came on with normal operation, but still wouldn't turn off.

I lowered the blade and left everything disconnected.

I will replace the switch and feel the motor after it has run for a while.

It is a puzzlement.

Warren

Re: What's going on with my table saw?

#19

Re: What's going on with my table saw?

Paul Waddle

>I would guess the starting and slowing caused the nut to loosen. Like some said,maybe its getting 110 volts instead of 220v. Strange noise,Id like to know too. pw

Re: What's going on with my table saw?

#20

Re: What's going on with my table saw?

Warren White

>As a follow-up, I thought I would post "the rest of the story."

I ordered the switch (a whopping $180.00) [they call it a 'starter']. It arrived while I was out of town.

I put the 'starter' on, wired it carefully according to the picture and instructions. Turned it on, and although I heard the contactor close, nothing happened. I sent an email to Delta (which hasn't been answered to date). With no answer, I called Delta and told them I thought the switch was defective. They asked if I had wired it right, and I said I had. They asked if I had wired it to the T1 and T3 terminals. None are labled T1 & T3, but I wired it according to the picture.

Well, she says, you wired it wrong. It should be to the teminals under that. It took a light and magnifying class to see that the terminals were labeled something like 3T1 and 6T3 (I am not home right now, so I can't tell you for sure that they were labled.

At any rate, the clearance between the terminals and the bottom of the box is too small to allow for a spade lug, so I just stuck the wire in the hole and tightened it up.

At least for the first couple of tries, it seems just fine. I want to spend a bit of time tonight and see if I can get a connection I can rely on a bit more, but for now I believe I am good to go.

Thanks for all of the suggestions!

Warren