Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Little electrical problem

Posts

Re: Little electrical problem

#26

Using smoke detecters in a shop

DB

>One problem with using a smoke detecter in a shop is that the detecter might not be able tell the difference between dust and smoke. There could be a lot of false alarms. Heat decters would be a better choice. Remote alarms are availble but you might have to go to a place that specializes in alarm systems, not a Home Depot type store.

Also dust can build up on any smoke detecters sensor over time making it impossible to detect a real fire. The smoke detecters should be vaccuumed out on a regular basis.

Re: Little electrical problem

#27

Re: Little electrical problem

Michael Wangler in Rochester, NY

>Ray,

I had a very similar experience at my house. It was during the Christmas season and every time I turned all the lights on the tree I would get a sense of 'plastic-type' smoke. I thought it was a new strand of lights on the tree. When I moved a chair to vacuum I found an unused outlet looking very similar to the photo you posted. The neutral was almost gone and the insulation melted back the plastic on the wire

I had a buddy who was an electrical engineer (former electrician) take a look. The conclusion was that it was a bad outlet. A slight bit of resistance going through the plug caused it to over heat. I did use the 'cheap' ($4 for 10 outlets, rather than the $3 for one...) outlets when I built our house.

One potential way to avoid this problem is buy using a pig tail in each box and connect the outlet to the pig tail. This way the load will no go thought the outlet. Even though the outlet that failed was not being used, it still carried all the load of the other outlets down stream.

Just glad we caugh it before it was too late...

Keep safe,

Michael

Re: Little electrical problem

#28

Side benefit to heat detectors.

Jason Roehl in Mulberry, IN

>They might tell you when your sawblades are dull!

Glad your shop is okay, Ray. I've seen a few smoked receptacles before, but none that bad.

Jason

Re: Little electrical problem

#29

Radio x-miter smoke detector

Lee Schierer - McKean, PA

>In my shop which is attached to the house I have a First Alert Smoke detector with a remote. The smoke detector (battery powered) sends out a radio signal when it goes off that sounds the alarm in the house. The receiver unit plugs in to the wall outlet. I bought this unit quite a few years ago and it seems to still work just fine. Anytime I use the wood branding iron to label projects and I forget to take the smoke detector out of the room, it goes off and also gets LOML alarmed because the one in the house goes off.

I don't think First ALert still makes them as I looked for a new one wehn we built the garage to store the boat so we could know if there was a problem there.

Lee

P.S. My smoke detector has never gone off due to sawdust in the air in my shop as it is the ionization type. You might have a problem with a photo eye type smoke detector.

Re: Little electrical problem

#30

Re: Radio x-miter smoke detector

Bill Howatt

>"P.S. My smoke detector has never gone off due to sawdust in the air in my shop as it is the ionization type. You might have a problem with a photo eye type smoke detector. "

I have an ionization detecter near my TS and fairly frequently set it off when ripping usually pine/spruce. Never see any smoke but something is obviously coming off.

Bill

Re: Little electrical problem

#31

Re: Little electrical problem - another

Tony Shaftel

>Go figure. Ray posted about his burned outlet earlier this month and for the first time in my life I experience the same problem. This was in the kitchen. Curiously, the downstream outlets were pigtailed, but this one outlet that supplied them was not.


img

Re: Little electrical problem

#32

Call the Manufacturer

Chicago Bob

>If you can still find the manufacturer's name on the device, email or call their customer service number. With CPSC & UL constantly looking over their shoulder, these folks will be more than glad to respond to your problems. Save the device(s) as they will probably want to have you return for replacement and failure analysis.

Bob

Re: Little electrical problem

#33

Re: Little electrical problem - another

Bill Howatt

>My guess the screw connection on the right wasn't as good as it should have been and it also heated the left one which isn't as badly damaged via the link between the two screw pads.

I had never thought of this issue as being a reason to use pigtails over daisy-chaining via the screws.

Bill

Re: Little electrical problem

#34

I dunno, but

Tony Shaftel

>Seems like the surface area of wire connected inside a wire nut might be greater than what you get under a screw. Then if over time the screw connection loosens, and two or three appliances are running...well, there you go.

In our kitchen it was possible that this outlet was running a coffee maker, the next one down the line a microwave, and the second one down the line a toaster. The 15 amp breaker never blew, but there it must have been close a lot.

Re: Little electrical problem

#35

Re: I dunno, but

Bruce Wrenn

>You said 15 amp breaker, but small appliance circuits have to be 20 amp. Push in's aren't allowed on 20 amp circuits. Now you can buy a type of push in that the screws tighten on the wire. Using push in's only the TINY spring makes contact with the conductor.

Re: Little electrical problem

#36

15 amp

Tony Shaftel

>It's an older house (1965), perhaps code allowed 15 amp back then. I'm assuming the electrician kept it all the same when the breaker box was upgraded a few years ago. The wires weren't pushed in, they were screwed on, thank goodness. I'd hate to think there are push-ins used on any ganged outlets in the house.

Re: Little electrical problem

#37

Outlet amperage rating ?

Pete LaBelle

>Be carefull wiring outlets.

Most of the $0.49 outlets at the home center are rated at 15 amps. Putting 12 gage wire in them and fusing for 20 amps could lead to this problem. For a shop, you'll want to pay the few extra bucks for the 20 amp plugs.

Pete

Re: Little electrical problem

#38

This comes up often...

John in New Mexico

>You can put multiple 15 amp outlets on a 20 amp circuit, though if they're GFCI's they must be rated for 20 amp feed through, standard outlets with pigtails it won't matter. I don't remember the page number and all that, but if you really want it I'll look it up.

John

Re: Little electrical problem

#39

Definately true, but...

Dan Donaldson

>For shop plugs, or for any that I know are going to get heave loads, I always get the 20 amp plugs just because they are a bit heavier duty than the 15's. For light loads I just use the 15's. I always use #12 wire for 15 or 20 amp circuits just because I have had too many times that I wanted to add a plug or something that drew a bit more and was glad to have the 20 amp capacity. (of course, I also tend to over engineer most everything ;-))

Re: Little electrical problem

#40

Sure, a good idea...

John in New Mexico

>But not an actual requirement unless the local authority makes an exception.

John