Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Router bit storage question...

Posts

Router bit storage question...

#1

JL

Router bit storage question...

JL

>I am building cabinets for my shop. I've accumulated a number of router bits over the years. Some are keepers, others are not. I figure on getting rid of the "cases" that some of them are kept it. I've seen the somewhat pricy brass inserts in the Lee Valley catalog as well as the inexpensive "advanced polymer" ones that you can screw into a backing board. I've also seen the interlocking bit trays that Klingspor catalog has to offer.

The LOML said "why can't you just drill holes in a block of wood?".

The Lee Valley catalog (and website) says: "One advantage of using these holders for bit storage, rather than simply boring suitably sized holes in a block of wood, is that they act as barriers against wood moisture migration, protecting bit shanks from corrosion." for their brass inserts and I presume that their plastic ones offer similar protection.

So - truth or exaggeration? How about blocks of wood? How about the Klingspor plastic blocks? What do you use to store your bits?

Re: Router bit storage question...

#2

Truth *LINK*

Dave's Not Here

>Bits stored in bare wood will attract moisture from the wood. I know this because it happened to me. Luckily I caught it in time before any real damage was done to my bits.

In addition to those products you mentioned from Lee Valley, CMT also offers a system for organizing your bits. You could buy their bit organizer and corresponding sized bushings and be done with it or you could just buy the bushings and make your own organizer.

My final choice was to go with the cheaper Lee Valley holders which I just screwed down to a piece of plywood. I initially bought some of the CMT bushings but didn't like them because I found that most of the time when I pulled out a bit the bushing came out with it.


CMT Router Bit Organizer

Re: Router bit storage question...

#3

Re: Truth

Lee Brubaker

>I'm amazed, I have been storing my bits in holes drilled in wood for more than 20 years & have never had moisture migrate to the shanks of my router bits. I currently use a take-off of Bill Hylton's bit tray that he lugs around from one site to another. Mine is mounted on the end of my router table & is a tray built from scrap. Consists of angled blocks with drilled holes for the bits. The aspect that I like is I can open the tray & see all of my bits without digging through dicky-doo drawers.

Lee


img

Re: Router bit storage question...

#4

Different Experience

David Yoho

>I turned a slightly damaged sink base cabinet our builder replaced into a router table and cabinet about eight years ago. Inside when I open the left door, there's a small four-drawer unit I cobbled together to store all the miscellaneous accessories and bits. I cut out pieces of maple I had on hand and drilled holes for bit storage. The maple blocks fit the inside of the drawers (2 of them) snug so they don't move around.

In the years I've stored my bits this way, I've yet to experience any problems with moisture corroding the shanks. Evidently it happens, but I haven't had any problems and the cost was right!

YMMV,

David


img

Re: Router bit storage question...

#5

Re: Router bit storage question...

George@Colonel's Workshop-Havertown PA

>Good Afternoon JL,

This is my own version of the Norm Abram approach. This is my second router table with bit storage drawers. I have never experienced any rusting/corrosion problem in any drawer in either table. Save yourself some money and buy a few more bits with the savings. Tell your wife she is right, and maybe she will let you buy even more bits. Talk about a WIN/WIN situation!

George


img

Re: Router bit storage question...

#6

JL

Re: Thanks for the idea, Lee...

JL

>That frees up a drawer in one of the cabinets! I have enough 1/2" plywood left to build something to attach to my router table.

Re: Router bit storage question...

#7

Mine all rusted, but not horribly..

vlparisian - Houston

>I built Norm's router table with storage drawers and love it, however the birch plywood did rust the shanks of all my bits including my Forsner drill bits. Why? Houston Humidity...

Re: Router bit storage question...

#8

Re: Router bit storage question...

Ray Newman

>I store my bits in the plastic boxes or in the small plastic/vinyl bags that they came. Some bits I keep in medicine jar bottles w/ a label ID-ing the bit; some in stacking Altoids tins.

After segregating by style, I then place the bits in several larger ZipLock (or similar) bags.

Nice & safe this way. Takes up a bit more space, but I don�t think not much more.

Before I did this, I had bit drawers on another router table. Once I pulled one of the drawers out too far & dropped all to the floor. Chipped a few bits � learned the hard way that good bits are expen$ive to replace. Sometimes I would cut myself trying to remove a bit.

Re: Router bit storage question...

#9

Problem with plastic inserts

Phil Joines Krum,TX

>I had 2 sets of the plastic inserts, both 1/4 & 1/2, and the tray that goes with them. The holes for the bits were enough undersize that they were a real bear to get out with the posibility of cutting myself on the really sharp ones. They went in the trash. I use wood and haven't had a problem.

Re: Router bit storage question...

#10

Re: I need to build a better storage system

Larry Clinton At Frankfort (Central)., Indiana

>for my bits. I was thinking the other day, why not cut off some lengths of PVC pipe. I have several different sizes laying around, I'm sure I can fit the 1/2" shanks, may have to buy a piece for the 1/4" but a length of pipe is real cheap. Thought I would make a drawer with a piece of birch (with the pipe inserts) ply spaced up enough to allow the bits to drop and line the bottom with plastic or cork. I'm sure I can make it for a lot less than the cost of the inserts. Right now I have them in a drawer of the router table in the cases / envelopes they came in plus a Craftsman router bit holder for most of the 1/4".

Re: Router bit storage question...

#11

What about ID'ing them??

Bri in Mtl

>What , if at all, do you do to indentify some of them?

I find that it helps if the radius or diameters of some that are close in size are ID'd somehow.

With a block of wood it's simple but with some of the above methods I wonder if it's possible somehow.

Re: Router bit storage question...

#12

Re: Router bit storage question...

Barry Irby

>I made a wall rack for mine out of scraps of wood. It has been in my unheated shop for about two years. Have not noticed rust on the shafts and more that when they floated around loose in the bottom of the a drawer. (essentially none) I did make the mistake of drilling the holes in the holders a 1/4 and 1/2". Apparently the wood shrank slightly and now the holes are "unpleasantly" tight. If you use wood, drill them a 1/64" over sized.

Re: Router bit storage question...

#13

Re: What about ID'ing them??

Lee Brubaker

>The angled blocks holding the bits re previous post w/pic have a 3/4"W x 1/8"D groove in the face & I started out by snapping a tight fitting piece of cardboard into this groove. Glued on the cardboard was the bit size & part number below each bit. Worked okay until addition of a new bit changed the line-up. Pain in the butt to change the cardboard so I don't bother with bit identification anymore.

Lee

Re: Router bit storage question...

#14

Ditto

Hank Knight from SC

>I had the same problem with CMT's plastic inserts.

Re: Router bit storage question...

#15

Re: Router bit storage question...

Tom Stockton

>I use wood no problem with rust. If your looking for another material those cheap white plastic cutting boards would be the ticket. I've run them thru most my tools and they seem to not dull anything, they are probably easier on cutting tools than some exotics.

Tom

Re: Router bit storage question...

#16

Re: Router bit storage question...

David Hay @ Denver

>I just drilled several holes in a piece of MDF that I keep in a cabinet. Never had any trouble with the shanks getting rusty, though I live in a pretty dry climate where rust is not usually a major concern...at least, not in the shop ;)

David

Re: Router bit storage question...

#17

Re: Router bit storage question...

Jerry Samsen

>I just picked up a phenolic cutting board and dilleed alternating 1/4 and 1/2 holes and mounted it using standoffs on a piece of 1/2" ply. Works great and the plastic does not bind the bit with humidity changes like wood would.

Re: Router bit storage question...

#18

Re: Router bit storage question...

NickB

>I use wood and haven't had any rust problems (here, in my Eastern MA basement, or in the San Francisco Bay Area). The wood I used well air dryed (some KD dimensional lumber that had been in my shop for a good long time).

I do think about the Lee Valley inserts, as I have had the bits stuck in there somewhat tight on occasion, but I've not had enough trouble to even get that one on the list (which is way too long to start with). I still have to finish putting the lighting up in the other half of the shop....

Nick

Re: Router bit storage question...

#19

Re: Router bit storage question...

John Ballance

>I store my bits in a piece of 3/4 HD melamine, drilled slightly oversized (17/32") and about 5/8" deep, with center-drilled 1/2 inch dowels serving as the bushings for the few 1/4" bits I have. Using a Sharpie, I can label every bit, and easily erase and relabel if I need to reorganize the bits. For my router table, I made the melamine the bottom of the bit drawer, to maximize the effective inside storage space.

No tight fit problems, and no rusting (live in southern California). Been using this system for about 5 years with no problems, but YMMV.

Good luck.

John