Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Cutting Melamine

Posts

Cutting Melamine

#1

Cutting Melamine

Larry in NW Ohio

>I`m going to try to repost this and see if I can hit someone, since I`d like to cut this tommorrow. How can I cut a sheet of melimine? Would a plywood blade or a fine tooth do it. Thanks again. Sorry for the repeat. Larry in Ohio

Re: Cutting Melamine

#2

Re: Cutting Melamine

Mark Mandell - Gone Round In Jersey

>Ask the Chinese. They're experts at cutting it with wheat and rice protein.

But if it's the sheet stuff you have, cut it like any high pressure laminate (Formica) by deeply scoring it with a fresh utility knife and then carefully snapping it on the score. Cut your pieces 3/4" more than your finished width and length, glue down, then trim with router. Put the edging on first, trim/sand flat with the top surface, then apply the top and rout clean.

mm

Re: Cutting Melamine

#3

Re: Cutting Melamine

AJ in Ohio

>Hi Larry,

As thin as melanine is it can be cut very easly with a laminate knife. If you choose to use a saw; a fine tooth blade will work. I spent many years doing laminate work and I found the best way to precut it was with a flush cutting router bit and a straight edge. I always cut about a half inch wild. Hope this helped.

AJ

Re: Cutting Melamine

#4

PS

Mark Mandell - Gone Round In Jersey

>I assumed that you're cutting plastic only. If you're cutting already-laminated sheets, use the finest blade you have but note that plastic will dull regular steel blades pretty quick, so carbide is called for. Also suggest you "tape" the cutline to help reduce chipping of the edges. Melamine's a bit softer that mica, but it still chips.

If you want to get obcessive about it, run you cut up to, but not through, the plactic layer from underneath, then score the top surface over the kerf and carefully snap the line. Lastly, trim the plasic back flush with a router and guided bit.

mm

Re: Cutting Melamine

#5

Re: Cutting Melamine

Bob Lang

>The best blade to use in your table saw is one specially engineered for this, most of them "high angle ATB". There are those that claim a triple chip grind is better, but my experience says otherwise. Take a look at th Freud and Amana sites. If you don't want to spring for a new blade, a cross cut blade with a lot of teeth will be your best bet. Carbide tips are a must.

Most of the chipping will occur on the bottom side, and a fresh zero-clearance insert will help tremendously, as will keeping the same face up as you make all your cuts.

Hope this helps,

Bob Lang

Re: Cutting Melamine

#6

Re: Cutting Melamine

Jim Swank

>Yeah, what they said. The important part being to cut oversize and trim to fit after gluing. On the tablesaw (face up), put an auxiliary table of 1/4" plywood on the table and up against your fence. On many fences, the thin laminate can slide under the fence and throw your cut off if you don't. DAMHIKT

Re: Cutting Melamine

#7

Laminate or Melamine? *LINK*

Derek

>It seems to me that people are getting Melamine coated particle board mixed up with plastic laminate.

You have two completely different sets of answers here. If you asking about melamine coated particle board, I suggest that you go with either a high ATB blade such as the Forrest Duralign Hi A/T (expensive) for the best cut or Freud LU80R010 (see link for good prices) or a TCG laminate blade for better blade life but not as good cut (e.g. Freud LU98R010).

You can also use a good crosscut blade to cut 1/16" oversized per edge and trim with a router to get a good edge. This is a lot more work and time but the cheapest route.


http://www.coastaltool.com/cgi-bin/SoftCart.exe/a/ab/forrest/forrest.htm?L+coastest+wbgt0363ff63eb63+1178009600#dura