Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

OT Need help making masks from plaster moulds

Posts

OT Need help making masks from plaster moulds

#1

OT Need help making masks from plaster moulds

Hamish

>Not a woodworking question but an artistic one.

In preparation for a coming fiesta, I have been asked to make a dozen African masks. So I made two plaster moulds and then sealed them with a celulose wall sealer which gave them a smooth waterproof finish. From these I intend to make a run of masks out of newspaper pieces stuck down with watered down pva glue. I tried making the first one and on drying, I found that I could not remove it from the mould, it had stuck. So by forcing it out and destroying it at the same time, I found that it also lifted off the sealing leaving the bear plaster again.

My question is how should I proceed now? Should I smear the inside of the mould with vaseline before continuing in the same way as before (I'm not sure if by putting on the glue with a paint brush that it will wash away the vaseline or not), or do you think if I apply the glue directly onto the plaster that on hardening the mask will come away from the mould? Any suggestion will be welcome.

Thanks Hamish.

Re: OT Need help making masks from plaster moulds

#2

Re: OT Need help making masks from plaster moulds

Ken Oakley-Sunny St. Cloud, Fla.

>If you are using a waterbased sealer and a waterbased media they will almost always adhere. Way back in my mold making days I had success using PVA,(Poly Vinyl Alcohol), I don't remember where I got it from though. I also made plaster molds for casting ceramic slip and the Master mold was made of Hydrastone, a very heavy dense plaster. After allowing the Master,(Block and Case ), to dry I applied multiple layers af a thick liquid soap solution, allowing drying time between application that became a parting agent between the porous Pottery plaster and the Hydrastone Block.

Possibly, and I am only guessing on this a liberal spraying of a silicone release agent might work. The other alternative and it might be pricey is to make the master mold of RTV, Room Temperature Vulcanizing, Rubber. Test some areas or items before doing a whole mask

Re: OT Need help making masks from plaster moulds

#3

Try flour paste instead of PVA

John in New Mexico

>Vaseline as a release should help a lot regardless of your mache binder.

John

Re: OT Need help making masks from plaster moulds

#4

Re: OT Need help making masks from plaster moulds

Phil Joines Krum,TX

>Seal the plaster with several coats of spray poly or shellac. Wax the mold each time before using it. The large craft stores might have spray release agent.

Re: OT Need help making masks from plaster moulds

#5

Re: OT Need help making masks from plaster moulds

Robin Corell in Atascadero CA

>for traditional paper making a celulose fiber(cotton,flax...) is combined with a small amount of starch and mixed with water. for casting paper the best mold material is standard 20 minute plaster with no sealer. the reason the mold is not sealed is so that the dry plaster mold can draw the moisture out. if the most is sealed there is a risk of mildew on thick sections.

paper machie is a variation on this process so I would do a test first an perhaps use less starch then normal.

Robin Corell

Re: OT Need help making masks from plaster moulds

#6

Re: Make them from Silicone

Charles Sharp

>Make your mold out of silicone (calking works fine). The rubber is flexible and won't trap your casting the way a rigid mold can.

Re: OT Need help making masks from plaster moulds

#7

Re:A word of thanks.

Hamish

>I would like to thank you all for your time, comments and suggestions. It seams that I need a releasing agent of some sort so that the mask and mould don't stick together. I also made some enquiries today around the art shops in my area, and was told to first spread hand cream around the inside of the mould, again to act as a releasing agent. So tomorrow, I will do a test on section on a mould that has not been sealed and with one that has. I'll post my findings later. So keeping my fingers crossed, I'll say hasta luego caballeros.