Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

WC Weekend Accomplishments.....

Posts

WC Weekend Accomplishments.....

#1

WC Weekend Accomplishments.....

Dennis E. Peacock

>Good Morning,

It sure is good to be home.

I spent last week in Philly for the day job and I took, well I should say that I had the opportunity to go and visit with Jim Becker and his lovely family. Jim and I exchanged bowls for gifts, I toured his wonderful home and shop and all but lusted over his LN low angle block plane. It just felt so good in my hands and worked so well. I had a very nice time with The Becker's and many thanks to them for their hospitality.

Sunday was a day I'll remember for a long time. Sam Maloof was in Little Rock and I got to go and meet him in person, sit and talk with him like we've known each other for years and have dinner with Sam Maloof, his wife Beverly, and the others that attended. What a humble man, very funny, and yet very caring about every woodworker. I am very grateful for the chance to meet and talk with Sam Maloof as I thought that I would never get to see anyone like this in my lifetime.

BTW, Congrats to Mark Cothren as Sam Maloof purchased one of his turned bowls out of the Historical Art Center!! Congrats Mark!!!!!

Today is as much shop time as I can get and I have to report back to work tomorrow.

So what did YOU do this weekend?

Best of weeks to you all.

Dennis


img

Re: WC Weekend Accomplishments.....

#2

Re: WC Weekend Accomplishments.....

Tim Caley - North Little Rock

>Hey Dennis, I'm glad you dressed up to go see Sam. :-)

Re: WC Weekend Accomplishments.....

#3

Surprise 40th Anniversary Party

George@Colonel's Workshop-Havertown PA

>Good Morning Dennis and a Happy Monday,

I wish I had known that you were nearby. We could have hooked up and spent some shop time together. On Sunday we celebrated our 40th Wedding Anniversary. Unlike the soft, warm April Day four decades ago, Sunday was filled with cold weather and driving rain. No matter: Kathy and I glowed like overcharged lightning bugs. We had been asked to have dinner on Saturday Night at a local country club by my best friend (and best man) and his wife. Charlie said his son had been given complimentary dinner certificates and couldn't use them. So he gave them to his Mom and Dad, and they invited us. We parked and entered one of the old stone restaurant buildings which had a cedar shake timber framed roof and exposed eaves/rafters. I was too intent on looking at the wood work to notice anything unusual. Each of our 10 kids, their spouses, and numerous very close friends had gathered in an adjoining room to surprise us. The astonishment was total. I guess there were many hints which we could have picked up on. However, this has been a busy time for Kathy and I, and our focus continually shifts. The kids each took part in a parent roast, and old friends told half forgotten stories of high school escapades. One of my boys put together a slide show which was projected on one of the walls. My #1 daughter made all the deserts including a new(and much better)wedding cake, which we duly fed each other to loud applause. I hope we can do it again in another 40 years. It was a great time. And all those who traveled here from Maryland and Virginia made it home okay. Great weekend.

George

Re: WC Weekend Accomplishments.....

#4

Completed My Son's Bed

Mike Fitterling

>I just finished this bed for my son, Jacob. It took about three solid days worth of work. Everything is cherry except the headboard panels, which are zebrawood. The contrast between the two woods ought to be much more dramatic once the cherry takes on that deeper red color it gets with time.

First; the Plans (not based on anything in particular, except the mattress size-twin):


img

Re: WC Weekend Accomplishments.....

#5

Panels Glued Up 

Mike Fitterling

>


img

Re: WC Weekend Accomplishments.....

#6

#46 Starts the Curved Rabbet 

Mike Fitterling

>


img

Re: WC Weekend Accomplishments.....

#7

Followed By a Rabbetting Block Plane:

Mike Fitterling

>Handtools were essential to this project. The #46, with its skewed iron lend itself well to cutting the cross grain on the curved parts of the panel rabbett (after being scored with my marking gauge). Once the shoulder was established, I switched to the block plane to fine-tune the fit.


img

Re: WC Weekend Accomplishments.....

#8

Mortises

Mike Fitterling

>Here are the mortises complete, done with my Jet benchtop mortiser and XY vise:


img

Re: WC Weekend Accomplishments.....

#9

Mortising the Rail Ends

Mike Fitterling

>The mortises in the end of the rails to accept the hardware were a bit more difficult. I clamped a couple boards flush with the end to creat a stable surface for the router and carefully cut them out with a 1/4" straight bit.


img

Re: WC Weekend Accomplishments.....

#10

Ellis Walentine

Hard to beat that, Dennis

Ellis Walentine

>What a busy time you've had. Congrats on meeting Sam Maloof.

Things are a little less exciting around here as I'm still nursing a back problem that I've had for the last week and a half. At least I can sit in my chair long enough to check my e-mail, but my WC time has definitely been curtailed. Yesterday morning, LOML twisted her foot while chasing some deer out of the garden, so she's laid up, too. It's like a hospital ward around here. Did I mention that taxes are due today?

:-/

The good news is that things can only improve. I hope.

Cheers,

Ellis

Re: WC Weekend Accomplishments.....

#11

Refining the Mortises

Mike Fitterling

>The hardware mortises required recesses for part of the hardware and, in this picture, a place for the male parts to insert before going down onto their seats in the female counterparts. I don't have a picture of it, but I also drilled 7/16" holes from the bottom, a bit in from the ends of the rail, and glued in dowels so that the screws holding the hardware would have something other than end grain to bite into. I used the brace and auger bits for this work (and the recesses in the hardware mortises). Neither the mortiser or drill press could drill sufficiently deep holes, but it was a snap with the brace.


img

Re: WC Weekend Accomplishments.....

#12

Tapering the Legs 

Mike Fitterling

>


img

Re: WC Weekend Accomplishments.....

#13

Finished Headboard

Mike Fitterling

>And, then glue up and finishing. I sprayed a coat of finish on the panels before gluing up the parts surrounding them. Finish was three coats of gloss Delft Brushing Lacquer sprayed with a HVLP conversion gun, followed by 600 grit wet sanding, then finished up with a coat of satin Delft lacquer.

Headboard:


img

Re: WC Weekend Accomplishments.....

#14

Finished Footboard 

Mike Fitterling

>


img

Re: WC Weekend Accomplishments.....

#15

Finished Rails

Mike Fitterling

>I would have liked to post a final picture of the bed complete with mattress, etc.; unfortunately, the recipient of the bed left the camera out in the yard all night and through a raging rain storm this morning.


img

Re: WC Weekend Accomplishments.....

#16

Congratulations, George

GolfSteve in Calgary

>40 years is special. Sounds like you had a wonderful time with your family.

Steven

Re: WC Weekend Accomplishments.....

#17

Steven Antonucci

Agree with Ellis- hard to top your weekend!

steve antonucci

>Of all of the "woodworking royalty" on the planet, Sam Maloof is probably on the top of my list of interested to meet. (James Krenov is another...)

I'm green with envy...

Steve

Re: WC Weekend Accomplishments.....

#18

Paying My Final Respects

Dave Morris

>Just got back from an eight day, 2500 mile trip to visit my wife's parents. Her father has liver cancer, and there's nothing to be done during what the docs say is a couple/few months at most. A sad week, a joyous week, and a special time to cherish those you love in your life.

Among the last in a generation not short on heroes, he survived the horrors of the beaches of Normandy, and was among the first to liberate those still alive from the horrors of the death camps. After the War, he served our country for another 40 years before retiring. A quiet and humble man, those we call "great" today would do well to learn from the examples in life shown by men such as him.

Dave--- who hopes he can arrange at least one more visit in the time remaining

Re: WC Weekend Accomplishments.....

#19

Green with envy!

Thomas Skaggs, Foothills of Mount Level

>Dennis,

Congratulations. You certainly had an experience that many of us would love to have, including me! Sam Maloof is a legend and rightfully so.

Last fall I had the pleasure of trying out one of his rockers. It was the first time I had actually seen one. Beautiful of course. But getting to meet the maker would be especially nice.

Thanks for the photo you lucky dog!

Tom

Re: WC Weekend Accomplishments.....

#20

Re: Green with envy!

Dennis E. Peacock

>Tom,

Sam stated that he had enough work on the books already...that he would be over 100 years old before they completed what's already been ordered. He is truly a great gentleman and excellent craftsman.

Dennis

Re: WC Weekend Accomplishments.....

#21

Re: Finished Rails

mdclor

>Mike,

Sorry about your camera. I really appreciate you documenting your process since I intend to make a bed once we are settled in our new location.

I agree that the woods will look great together.

Thanks,

Merle

Re: WC Weekend Accomplishments.....

#22

Re: Paying My Final Respects

Larry in NW Ohio

>Dave Give him my eternal gratitude. Larry

Re: WC Weekend Accomplishments.....

#23

Darrell in Oakville

Re: WC Weekend Accomplishments.....

Darrell in Oakville

>"With mallets aforethought" as Roy Underhill would say...

This weekend I made a dozen croquet mallets for my daughter's Cub Pack. It's for a game at their June camp. I dug through the firewood pile for some suitably dry hardwood, and found some paper birch. I turned these into more-or-less 6 inch long cylinders, as fat as the wood let me. And then some, as a number of these have flat spots on them.

Luckily for the budget-minded Akela, this week is Junk Week in our part of Oakville. You can throw out anything but toxic waste. Everyone goes into a frenzy of spring cleaning and the scavengers grow fat on the curbside spoils. Far be it for me to deny my Scottish heritage (maternal grandfather), so off I went to pillage the piles of roadside debris.

I found plenty of broom handles which I used for the mallet handles. A bit of spokeshave work was needed on a few of the handles as they didn't fit the holes my forstner bits made in the heads. Nothing fancy, just some brute force ugly wooden hammers to amuse a bunch of 10 year olds for an hour. I used my post drill to bore the holes. That machine is *such* great fun to use, I don't understand why anyone would want an electric drill press.

I glued and wedged the handles in the heads, so hopefully they won't come flying off. Maybe I should put pins through them crossways too? I could use my post drill again... :^)

Michelle says she can't wait for Whacking Day!

Darrell

Wood Hoarder, Blade Sharpener, and Occasional Tool User


img

Re: WC Weekend Accomplishments.....

#24

Re: Paying My Final Respects

Jennifer@Indy.USA

>Dave, these men are treasures to all of us. You're blessed to have known him. What a long and amazing life he has spent here. I sure do hope you get to see him again.

Jen

Re: WC Weekend Accomplishments.....

#25

Re: WC Weekend Accomplishments.....

Dominic Greco in Richboro PA

>Dennis,

You wrote:

"I spent last week in Philly for the day job and I took, well I should say that I had the opportunity to go and visit with Jim Becker and his lovely family"

You were up here and didn't tell me! I think Jim lives all of about 10 miles from me! Oh,.......the INSULT! :>)

Maybe next time!

See ya round,

Dominic