Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Help!! Pipe Clamps Slipping...

Posts

Help!! Pipe Clamps Slipping...

#1

Help!! Pipe Clamps Slipping...

Dave Winters

>I've taken the "fingers" out and reversed them, this helps a little, but I'm afraid the 3/4" pipe I'm using is excessively soft. You can see on the pipe where the clamp is slipping and "tearing" the metal. Doesn't take much pressure to get 'em to slip.

Are there different grades of 3/4 pipe and if so what are they?

Anybody else have this problem.

What's the best stuff to use?

Re: Help!! Pipe Clamps Slipping...

#2

Re: Help!! Pipe Clamps Slipping...

jmohnike

>Are you useing black pipe or galvanized? Galvanized will slipp with any clamp that I have used and any size pipe.

Re: Help!! Pipe Clamps Slipping...

#3

a permanent solution

Bill Tindal, E.TN

>I solved the slipping problem as well as the flexing problem by selling my pipe clamps and buing bar clamps. If you do much gluing pipe clamps are just too much aggravation to endure. I am growing very fond of the aluminum bar clamps made by Universal.

Re: Help!! Pipe Clamps Slipping...

#4

Re: a permanent solution

Larry in NW Ohio

>Bill Where does a person find The Universal clamps? Thank You Larry in Ohio

Re: Help!! Pipe Clamps Slipping...

#5

source of Universal clamps

Bill Tindal, E.TN

>these clamps are hands down the best bar clamps available unless you think you need the long jaws of Bessys which I have not ever found necessary. The thumbscrew is a huge advantage over competitive clamps and they are so strong that furniture factories tighten them with an air wrench.

I have seen these clamps at Woodcraft and Manney's in Lexington. But we get them direct from the manufacturer for about $15 per clamp. It is a great club project. They must be ordered in lots of 10 for each length 2' to 6' in 1 or 2' increments. We get together a club order, usually 50 -100 clamps at a time.

To order from manufacturer callKeith Clark at Dubuque Clamp Works, Dubuque Iowa 563 582 5102

They were made by a nice family in CA but they got overwhelmed and sold out.

Re: Help!! Pipe Clamps Slipping...

#7

2 types of pipe clamps....

Mark Goodall - ATL - tooljunkie

>I've owned two types of pipe clamps....

Inexpensive red clamps from China. MOre expensive orange Pony clamps made here.

The red clamps had a serrated "finger" that tried to grip the pipe. Utterly useless with galvanize pipe, fairly useless even with softer black pipe. They would dig in, and scrape the metal, and slip.

I gave them away because I didn't have the heart to take any money for them, although the store that I bought them from earlier was more than happy to take my money. Lesson learned.

THe Pony clamps have a bunch of rings that grip the pipe. They work much better, and I'm happy with them, as far as pipe clamps go.

Happy Woodworking!

Re: Help!! Pipe Clamps Slipping...

#8

Re: Help!! Pipe Clamps Slipping...

Barry Irby

>I have some of each type, the finger version with the serrated gripper and the Pony ones with the rings. The rings are definitely better. I also use them on both the black iron and galvanized pipe. Black iron is better.

I read here on Wood Central that there is a wide variety of black iron available with a lot of it coming from China now and that some is slightly undersized. If you have the undersized pipe, the clamps won't work well. Short of carrying a micrometer with you to the store, I don't know how you would tell if the pipe were undersized. Perhaps you could buy a piece and try it out and if it worked go back and stock up.

I cleaned the black iron very thoroughly and then sprayed it with lacquer to help reduce the staining where it touches the wood. helped a little. Tape or a piece of plastic between is better.

Re: Help!! Pipe Clamps Slipping...

#9

I agree with the advertising claim

Bill Tindal, E.TN

>After using them for 3 years I agree with everything in the description, except they are no longer made by the nice folks in CA. When I would call I would get various family members and a "handshake" over the phone was all the agreement needed to have an order sent.

Re: Help!! Pipe Clamps Slipping...

#10

Re: I agree with the advertising claim

Bart Leetch

>I have pipe clamps I started with 2 of Jorgenson's Pony's & then went to the same style Harbor Freight clamps. I have mostly galvanized pipe & (6 black pipe clamps used very little). Black pipe was the biggest mistake I ever made yuck never again. I purchase old used galvanized pipe it works great & I used get it for around $2 for 20'. I found out that 4'6" lengths were the best size & for longer lengths use pipe couplers. Dad & I have about 80 combined years using pipe clamps. I have all of Dad's finger version with the serrated gripper Craftsman 3/4" pipe clamps that he purchased for about $2 each in the late 50's & early 60's these will be my back up clamps I primarily use clutch style pipe clamps. That reminds me there is between 50' & 100' of old 3/4" galvanized pipe waiting at Dad's for me to haul it home. FREE.