Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

How would you do this - Need Advice

Posts

How would you do this - Need Advice

#1

How would you do this - Need Advice

Joe in a Cleveland suburb

>Hi folks.

Somebody asked if I might be able to do something for them as described below and in the picture. I am thinking one way would be to use a router, a straight-cut bit and some kind of jig for the router to run on. I have absolutely no clue how I would figure out where to cut, at what angle to cut and so on. I would greatly appreciate any advice, suggestions, and so on.

Below you see a tapered column. The idea is to cut a slice out so the column fits on the outside corner of this cabinet looking thing. I suppose the column would be set in so the bottom outside corner of the cabinet is about half way in to the column. So at the top of the column, because of the taper, it would only be in part way. Hope that makes sense.

Suppose you only get one shot at it and it needs to fit nice. This column was something the owner inherited from a Great Grandfather and you really don't want to screw it up. How would you do it?

Thanks.

Joe


Re: How would you do this - Need Advice

#2

with a table saw and jig

Ian (in Sydney, Australia)

>Joe

my initial reaction is make a jig that will hold the column horizontal and then cut a quarter out of it using a table saw.

you might cut the end caps off first and glue them back afterwards if the finished unit would look better that way

what you're looking to do is a fairly common detail, albeight usually with smaller diameter columns, so there should be a how to out there some where

Re: How would you do this - Need Advice

#3

Rick L

Re: How would you do this - Need Advice

Rick L

>You need to do more reading of technique books on routers.

For paint grade it would be glued in quarters with a paper joint to pop out the section you don't want. The other way is to screw square guide plates on the end to give co-ordinates and reference points to work from. Could also be triangles, octagons, etc. We do this all the time with logs for specialty architectural elemements for timber framing.

Re: How would you do this - Need Advice

#4

Re: How would you do this - Need Advice

Paul Woolson

>There was just a "tutorial" posted of a guy that makes really big tables. In it he has a photo of his setup to flute the post. He set his up on a lathe with a homemade indexer. You don't need a lathe but that will give you an idea of how to do it.

On fitting it to a cabinet: I'd make a dummy post first and do my experimenting on that. Then when you are dead sure it's right, go to the real deal.

Re: How would you do this - Need Advice

#5

Build a duplicate

Curly Smith

>If I were intent on destroying the original, I'd go with what Ian suggested. Build a jig (something along the lines of the router fluting jig) that will hold the column firmly and is square to the fence. I'd then, after some trial runs on a suitable alternative, cut a "V" to fit the corner.

However, if the column was really from Great Grandfather, I'd build a duplicate to chop up and use the original as a column for a high table. If it's old and important, why destroy it for a corner post? What happens is 5 years when the owner moves? They could take the high table with them, they'd have to leave the chopped up original.

IMO cutting the original for this application is a very, very bad idea and one that the owner will come to regret and I wouldn't want any part of it. It's like people bringing you antique chairs to refinish... you can do it but should you?

Re: How would you do this - Need Advice

#6

Re: How would you do this - Need Advice

Ron Bauman

>What's to stop you from cutting the cabinet and scribing the hole to fit the column? Would save the keepsake.

Re: How would you do this - Need Advice

#7

Re: How would you do this - Need Advice

Keith Newton

>I would make a sled, just two pieces of plywood stapled together the length of the column, to give a straight edge to ride the fence. You can not set the fence any farther over than the height of the blade, or the kerfs won't meet in the middle unless the column is hollow.

Re: How would you do this - Need Advice

#8

Re: How would you do this - Need Advice

Thomas Skaggs, Foothills of Mount Level

>If you use a dado blade then you could do it in one or two passes without having to turn the column and match kerfs.

T.

Re: How would you do this - Need Advice

#9

Lee Gordon

Re: How would you do this - Need Advice

Lee Gordon

>Maybe I'm wrong but I was under the impression that this is exactly what he was asking how to do: how to cut away the corner of the cabinet so the column (uncut) can be fit into it. I certainly hope so because, from the looks of it, the cabinet is much more "replaceable" than the post. If that is indeed the case, what I would do is lay the column flat onto a sheet of thin plywood, MDF or masonite and trace the outline onto the sheet goods. Then I'd cut along the line to create a pattern and scribe or otherwise tweak it until it made a tight fit with the center line of the column. I would then use that pattern (on both adjacent sides of the selected outside corner of the box) to cut away the corner of the cabinet and insert the column into the resultant void. I would probably attach it with double-stick tape or a few dabs of clear silicone caulk -- definitely something reversible.

Re: How would you do this - Need Advice

#10

I hope you're right

Curly Smith

>As I said, I hope you're right by my impression was that the intent was to cut the post.

Instead of tracing the column why not build a niche (round, oval, square?) to highlight and display the column? Might look a lot better, it'd be a lot cleaner, and it'd certainly be easier.

Re: How would you do this - Need Advice

#11

Re: How would you do this - Need Advice

Rick Snyder

>I agree totaly with Lee, adjust the cabinet, NOT THE COLUMN!

Rick