Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

table saw dust collection

Posts

table saw dust collection

#1

table saw dust collection

mike mcnerney

>I am finally hooking up my saw for permanent dust collection, 1.5 hp, around 1100cfm. First, would one of those 4" cyclone lids be of any use or is the dust too fine. I thought it would be easier to empty that more frequently than the big bag on the collector. Can I put a plastic bag in the cyclone pail as long as I weight down?

If I want to use a separate, over the top of the blade collector, can I hook that up to my new collector, or should I use my shop vac?

I've got a job coming up using padauk,& I remember from years ago its dust being particularly annoying.

Mike in Ottawa

Re: table saw dust collection

#2

Re: table saw dust collection

Randy Johnson Connersville, IN

>One place where just about if not all tablesaws fall short in the design department is dust collection. Most of us have the ducting overhead. With this setup the duct is going to have to come in from the right. Most saws have the port on the left of the saw, a few have it on the rear of the saw, but I don't know of any that have it on the right of the saw.

Either of these choices make you add air flow robbing bends to the system. I cut a hole in the left side of my saw and used a HVAC boot to connect to the pipe. Since I have one of the saws with a left side port this eliminated two 90 degree bends. It also allowed me to increase duct size from 4" to 5". I have 6" going to the saw. At the overhead bladeguard/DC I wyed with 4" going to the overhead and 5" to the saw. It is all connected to a 2hp cyclone. Even this setup doesn't get all the dust the saw produces but compared to the ammount the collector got before the modification there is a marked improvement.

Re: table saw dust collection

#3

JL

Re: table saw dust collection

JL

>In regards to your first question. I don't have the cyclone trash can lid. I do have something similar made out of a 30 gallon drum and plumbing parts. This gets about 50+ % of the dust from my table saw, the rest goes into the DC bag. I've never really measured the amounts.

I don't know if the plastic bag would interfere with the "cyclonic efficiency" - the principle is that the air swirls around the trash can or container and drops its load of dust. Plastic bags are cheap. So give it a try.

Re: table saw dust collection

#4

Re: table saw dust collection

Barry Irby

>I would be careful about the plastic bags. I use my DC as a shop vac and sucked up a bag. It got lodged in the impeller and I had to partially disassemble the system to get the bag out. Might have been bad if I had not realized it. (You have to be deaf to not know something was wrong. At least in my case.)

I think I would try a piece of plywood like a disk and drop it in the bag into the bottom of the trash can. Of course you would have to empty the bag to get it back. Someone made a bag holder that can be inserted from the top, like a series of verticle ribs that could be pulled out, attached to a ring.

I just modified my setup to make the DC bag easier to empty to eliminate the separator trash can. The can was always in my way and may have robed some efficiency. I may still bring it in for stuff like the planer. I don't think the TS produces nearly as much debris as the planer.

Re: table saw dust collection

#5

Re: table saw dust collection

Chuck Lenz

>The purpose of a cyclone lid is to take the HEAVY particles out of the airstream before it hits the impeller on the dust collector and damages it, plus it cuts down on haveing to empty bags as much. But you should be emtying your lower bag and cyclone lid container after each days use to prevent a fire that maybe smoldering when your away. I would think you could use a 4" line below the saw and a 2" line above the blade to your collector and be ok with it as long as you don't let your lower bag get too full. If your dust collector and shop has the option of wireing it to 220 volt, by all means do it.

Re: table saw dust collection

#6

Re: table saw dust collection

Pete LaBelle

>I too have one of those trash can lid pre-separators.

You'll need 2 4" hose couplings to permanently mount to the lid. A few nuts & bolts, some wood shims, and silicone caulk will secure the fittings and give the hoses a better seal.

Install some foam weatherstripping on the edge that contacts your can.

On your can, cut a 1" wide opening, 4" from top & 4" from bottom, and screw & seal in a piece of Lexan to use as a sight glass. It needs to be dumped when about half way, else more stuff starts heading to your bags. I empty this 10-15 times before I disassemble the DC bag for cleaning.

Pete