Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Need help with sanding (paint removal)

Posts

Need help with sanding (paint removal)

#1

Need help with sanding (paint removal)

Dustin

>I have an old jenny Lind cradle that I am trying to re-finish for a new baby. It has several posts and is taking forever sanding by hand. I have tried sand blasting using very fine sand (pitted the wood) and stripper though it is very difficult to get all of the material from the grooves. Is there any better way to complete this task rather than sanding by hand? I Seriously need some help from the experienced.

Thanks,

Dustin Fletcher

Houston, TX


img

Re: Need help with sanding (paint removal)

#2

2 words: dip tank

Rob Sandow

>There is no other way to really remove the finish from an item like that. Look in the yello pages for furniture refinishers, call them and ask if they have a dip tank, and if so would they take your piece for a stripping job.

Rob

Re: Need help with sanding (paint removal)

#3

Re: Need help with sanding (paint removal)

Larry Clinton At Frankfort (Central)., Indiana

>I recently stripped a chair for my sister (BIL's family heirloom) that had numerous coats of various finishes. It had carvings and turned spindles with grooves. I used the pink citrus based stripper - can't remember the name at the moment, but I have some in the shop. I bought it at Lowes. If you need the name email me and I will send it to you. The coating is a gel. I put it on thick, allowed it to set the required time, and then washed it off with a garden hose in the driveway using an abrasive woven pad to clean the area while rinsing. 99% of the finish came off easily. A few areas took a second coat of stripper. Of course you have to sand the wood after the water raises the grain. This was a lot messier than a dip tank - but also a lot cheaper. I had no residual finish in any crevices when I was done. I would do the same thing again. The chair had been stained and there was variation in the color when I finished, After the chair was repaired, cleaned and sanded, I wiped on several coats of orange shellac. I (and my sister) was quite pleased with the appearance when completed. YMMV but I would certainly give it a shot.

Re: Need help with sanding (paint removal)

#4

Re: Need help with sanding (paint removal)

Gary Hoemann

>I have used a stripper from 3M called Safest stripper. It is very thick and clings well. Probably the best thing to do is coat each spindle well and wrap some plastic wrap around it. Leave it for a long time, maybe 24 hours. It does the trick, but my problem is always impatience and not wanting to wait long enough

Re: Need help with sanding (paint removal)

#5

Re: Need help with sanding (paint removal)

jmohnike

>I have stripped many items similar to yours. It is best if you can find a large shallow plastic tray or make one out of wood (line it with a garbage bag) that you can lay your cradel in. I use Stripease remover, keep the remover wet keep brushing it on. WEARE GLOVES & EYE PROTECTION remove stripper and paint with steel wool, use a medium stiff brush in the difficult areas, repeat if necessary. Wipe everything down with laquer thinner or acetone WEAR GLOVES & EYE PROTECTION, then wipe down again with a mild solution of liquid dishwashing detergent and water, wipe again with clean water, with a lite sanding you should be ready to finish.

Make sure finish is child safe and do not forget to WEARE GLOVES & EYE PROTECTION.

Joe

Re: Need help with sanding (paint removal)

#6

If I am reading your post right

Don Henthorn

>you have the finish off and want to get sanded smooth. With all the spindles and posts I don't know of any fast way to get it done. Slow old hand sanding is the only way I can see without disassembligh the whole thing.

Re: Need help with sanding (paint removal)

#7

two answers

Michael Dresdner

>If you are asking how to strip the finish, do it chemically. All paint removers work -- the difference in type has to do with speed. High methylene chloride content strippers are far and away the fastest and make it easiest to dispose of the stripping gunk. As strippers get safer and less odiferous they get slower. You make the choice, but in all cases, let the stripper do the work.

If you have stripped the piece and want to know how to sand it, odds are you do not have to. Unless you use a water based stripper, there is usually no need to sand after stripping. However, if you want to sand but can't face all the steps in the turned posts, use a 3M Roloc Bristle Disk. These slick tools are a disk of plastic fingers on an arbor that goes into a hand drill. The bristles themselves are impregnated with grit. They come in all grits and will sand without ruining the contours.