Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

The new bandsaw saga begins

Posts

The new bandsaw saga begins

#1

The new bandsaw saga begins

albertabob

>Bright and early yesterday ,morning I headed out to pick up my new 18" Bandsaw.

The store had not phoned me but I was confident it would be there.

Sure enough it was sitting there in a big box.

First problem, I drive a van and have the back split with 3/4" plywood horizontally to get more storage space.

In this case the "shelf" was an inch too low for the bandsaw to slide under.

Out comes the electric screwdriver and the shelf is now disassembled and shoved to the front of the cab and the saw is now on it's side in the cargo space. -- Did I mention that this thin weighs a mere 400 lbs.?

Now proceed back to the shop.

First new problem:

I can't get it out of the van. Not a problem I'll just hook a rope on the forklift and drag it out to the floor.

So far so good, I at the stage where it needs to be stood up again.

I can't get enough purchase on it to upright the cardboard box, so out comes the nylon tow rope and a come-along and I manage to get it standing.

There is a metal shipping base on the saw so I now load the thing on to a dolly to make my passage over to the saw area as the forklift will not make it around the tight corners.

Success!

Off comes the cardboard shipping box and there she be!

I rush up to my upstairs shop and start assembling the mobile stand for the base. There are no instructions so I line up all the part on the bench an start.

A few minutes later realize I put the swivel casters on the back legs and the rigid ones on the front. Another 15 minute they are switched to the right positions. ( this is more or less stand procedure for me and mechano sets)

Next assemble the corners with the caster to the side bars.

What? there are two left front caster assemblies.

back in the truck and wait patiently in line to get and exchange then back to the project.

What? There are also two left back casters assemblies! (Oh Joy!)

Back I go again! 20 km round trip BTW.

O.k. It's all assembled! I take a measure to be sure that it will fit the base of the saw. EEEEEEK! It's 1 inch too short!

Back I go again to the bandsaw place and buy another stand for $70.00.

It's 3:30 in the afternoon now and I'm whipped.

The mobile stand is in the van and I am contemplating my next move.

Today I have to figure out a way to hang the bandsaw by it's upper member in order to slip the mobile base under it.

Then it's on to putting on the table and fence.

That should be a piece of cake.- Considering.

Bob


img

Re: The new bandsaw saga begins

#2

forklift???

Pat Evans

>Must be nice! A few weeks ago, I set up my new bandsaw without benefit of a forklift. Last week I had to see a doctor about a hernia.

Re: The new bandsaw saga begins

#3

Re: forklift???

albertabob

>I got mine sewed up a dozen years ago.

Bought a forklift after that.

Bob

Re: The new bandsaw saga begins

#4

Re: The new bandsaw saga begins

Garrett in Victoria BC

>Hi Bob

Very nice saw. Sounds like one of my experiences.

I bought a Craftex 20" bandsaw about 8 years ago (650 pounds) and went to pick it up with a little utility trailer. One look and I decided to have it delivered right into my basement by 3 very muscular movers who had the right equipment. OTOH, I (foolishly) moved my Delta 15" planer in by myself, and assembled it with the help of make-do equipment.

Enjoy, Garrett


img

Re: The new bandsaw saga begins

#5

Re: The new bandsaw saga begins

albertabob

>Thanks Garret:

If I had not conjured my wife into makeing a few projects in the shop I might have struggled with the old machine a while longer. She made a couple of cuts with the old machine and said "You should get a new saw".

I had to move quickly on that advice.

You are right about struggling with equipment.

I never seem to learn when to hand off some of the tougher stuff.

It's up and running today and should be a fine addition with a few minor tweaks.

Re: The new bandsaw saga begins

#6

We (wife and I) used pipe clamps.

Eddie Pacheco, San Jose, Ca.

>Yes, pipe clamps. When we had to mount our Lagune 18" bandsaw on a mobile base we were wondering how the heck we were gonna do it. We tilted the saw ( I guess right to left when viewing the front) and I held it at an angle while my wife slipped in the MB as far as it would go. Together we then let the saw down to where it was midway on the base and midway off. Not being able to secure the base while trying to slide the saw, I grabbed a pair of Jorgeson pipe clamps and hooked the crank end to the base and the other adjustable end to the base of the saw. I started turning the cranks to get the saw to move, then readjusted when I ran out of thread on the crank. I repeated this a few times until the saw dropped into the mobile base. It's only a 1" drop from the top of the bases tubing to the resting shelf on the base so no damage to the saw or our fingers and backs. Try it out.