Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

How to read notes on truss plan?

Posts

How to read notes on truss plan?

#1

How to read notes on truss plan?

John in New Mexico

>We just had our framing inspection- all went well except we have to add nailing on 2 and 3 ply trusses in a specific pattern. Turns out the truss co. forgot to send the spec sheets along, just sent the layout sheet. Sorry if its a dumb question, but what does 0-7-0 oc spacing mean? The oc I can figure out, but the shorthand has me confused. Some are 0-4-0, some 0-9-0, etc.

Thanks,

John

Re: How to read notes on truss plan?

#2

Re: How to read notes on truss plan?

Al Stokka - Cambridge, Iowa

>John,

I'm not an expert on trusses.

Just a guess: Looking at truss plans on-line, it appears that truss manufacturers use dashes to delineate dimensions, rather than foot and inch marks (', ") and fractions (�). For a simple gable-style truss for a 26' span I see 26-0-0 for the span, 13-0-0 for the peak location, and 4-7-15 for the rise (from wall plate) and 5-3-3 for the overall height (including overhang at the eave).

Those numbers suugest to me that their nomenclature is:

4-7-15 equates to 4 feet, 7 inches, and 15/16 inch.

So, for you dimension of 0-7-0, the dimension would be 0'7" (no fractional inches).

Would such a dimensioning sustem fit with your trusses?

Al

Re: How to read notes on truss plan?

#3

Sounds about right

John in NM

>Its that last zero that throws me, since if they're using decimal inches, I'd almost expect decimal feet too, but then there'd be no need for the decimal inches! I think I can find a bottom chord spec to check it, or even climb up and measure one of the spec'd truss heights, I was just hoping someone would already know and save me the trouble ;).

Thanks for the response

John

Re: How to read notes on truss plan?

#4

Re: Sounds about right

John Foster

>I work at a truss shop, and you are correct. For instance 10-7-11 would be 10 feet,7 inches and 11/16ths.

Re: How to read notes on truss plan?

#5

also:

John Foster

>I am in Canada, but for a truss company not to send drawings, specs, instructions etc is a grave oversight, and they should forward them to you pronto.

Re: How to read notes on truss plan?

#6

Thanks!

John in New Mexico

>Good to have confirmation!

They did email me pdf's promptly. The building inspector says he's always having to get builders (not just owner builders like me) to go back and get the actual plans from the truss suppliers. Guess they like winging it out here in the sticks.

John

Re: How to read notes on truss plan?

#7

I'll just add at this point...

John in New Mexico

>All this nailing SUCKS! Sure would have been easier before the sheathing was on, or even before there were roofing screws sticking down through it!

Well, one done, two to go. My opinion of my truss supplier has dropped rapidly in the last 2 hours.

John

Re: How to read notes on truss plan?

#8

Re: I'll just add at this point...

Rob Stokes in North Vancouver

>If I read this right....

you ordered engineered trusses

trusses were delivered (and installed)

inspector wanted more work done to the trusses (design/construction modification)

you're doing the extra work

And you paid these guys?

I'd call them up and let them know when they're welcome on the building site. At an absolute minimum, send them a bill for your labour..

Rob