Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Building a New Barn

Posts

Building a New Barn

#1

Building a New Barn

Ed Wesolek

>Hell-o People,

My wife as consented to let me build a barn this summer. I am going to build a 60' x 40' x 12' high. 40' x 40' for my wood working area, then have a 10' x 10' for a spray area and storage for stains and finsihes, the balance for the floor heater and wood, along with some storage for yard tools, not much.

My question is, have any of you run your vacuum system under the radiant floor heating along with some of the wiring? The wiring being for the sander, planer, and table saw along with the vacuum system. The vacuum system would also be run under the floor for other tools as well and not have any pipes over head.

I am working from a clean piece of paper and would love your input. You really helped me out when I asked for info on tools and it has been very good information. That is the reason I am asking again.

Thanks for your input.

I will stay close to the computer tonight and see what you have to say or what questions you might be asking.

Ed Wesolek

Re: Building a New Barn

#2

Re: Building a New Barn

Ken Romines

>Ed

I don't have any experience running wireing under a slab. That said, I am considering a shop and doing the same thing. I am considering running plastic pipe under the slab that is big enough to push the wire through and/or remove it when I no longer need power to that area. Just an idea.

Enjoy the planning and let us know what you decide.

Ken

Re: Building a New Barn

#3

Re: Building a New Barn

Kirk (KC) Constable

>Without even knowing what kind of things you do, I'll suggest the finishing room is too small... especially if it has a solid door closing it off. Spraying a 5' long table will make a 10x10 room crowded in a hurry.

KC

Re: Building a New Barn

#4

Suggestions from my experience.

Mac in Indy

>Ed,

Let me tell you what I did and see if you can get any ideas from it. about 5 years ago I built a new shop with a garage attached. about a thousand sq ft overall evenly split between the shop and garage. I knew I wanted wood floors in the shop and I wanted to keep the dust collection out of sight as much as possible to reduce the visual clutter, allowing for a more open feel to the shop. I also knew from the beginning that I wanted really good Air Conditioning so a small forced air system made the most sense for me.

What I came up with was a foundation block stem wall and slab for both areas. In the shop I put in a 2x8 floor joist supported at their ends by treated 2x4 sleepers. I ran 16" wide pipe chases around the perimeter of the shop and one down the middle. I installed plywood subflooring over everything leaving the pieces over the pipe chases removable. On top of that I installed 3/4 oak hardwood (durable and inexpensive floor covering if you stick with off cuts and seconds) again flooring my pipe chase covers with flooring such that they were removable. I reinforced the pipe chase covers with angle iron to keep them flat.

My cyclone is out in the garage area and the piping enters the pipechases through a hole in the block stem wall seperating the shop and the garage. It has a return air vent directly into the shop. The tools are plumbed with their DC up through holes in the pipe chase covers and the blast gates are all above the floor. I also have wiring for the tablesaw running through the pipe chase.

The HVAC unit and piping are all in the atic. I also put small awning windows up high on the south and west walls to admit as much natural light as possible.

Also consider a master switch that disconnects all the power tool circuits (not the lights or non tool outlets). I did this via what is called a contactor switch (here at work we call them relays). Talk to your electrician and he'll know what you are talking about. I like it from a safety and security standpoint. No body goes in my shop and accidently turns on a tool without turning on two switches, the master switch and the tool switch. I have 110 every 4 feet along the perimiter of the shop and a 220 circuit on each wall. If needed I can run circuits through the chase as I ran a couple of spare wires down there from the breaker box before closing in the walls. If I did it again I'd make it easier to add ciriuits up and down out of the box by making removable access panels.

For task lighting I am a big fan of track lighting like you get at the borg (Lowes, HD). I have color balanced florescent general lighting but I have two circuits of track lighting that run above all the tool and bench areas. I can add, move or eliminate task lighting as needed.

What I like about the setup I have is the flexibility I have built into the shop. While I have yet to do a major change I know it is not a problem since my lighting and dust collection can be moved with a little effort. The goal of low visual clutter has been achieved and everything works pretty much as I had envisioned. Let me know if you have any questions either here or via e-mail.

Mac

Re: Building a New Barn

#5

Re: Building a New Barn

Lee Schierer, McKean, PA

>My only thought is that you better be sure you will never want to rearrange if you run your DC piping under a concrete floor. The pipe chase idea or even a conventional joist type floor over a crawl space would give you more chances to rearrange machine locations in the future. You never know when Santa might bring you a CNC routing machine that won't fit in your exisitning layout.

Lee

Re: Building a New Barn

#6

Re: Building a New Barn

Terry Quiram

>Ed

I have a radiant floor in my 32 x 44 shop. I ran my electrical on pvc before pouring the floor. I also laid a trough in the floor for my dust collection ducting. The ducting is easy to get to by raising a wood floor section. The trough will accept a 6" line.


img