Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Cost of building a garage

Posts

Cost of building a garage

#1

Cost of building a garage

Josh in VA

>We recently moved into a new home (King George, VA) and made a little money on our last house. As the wife can't stand the mess when the shop is in the basement we have decided to build a detached garage/shop. I had planned on building it myself but my work schedule just will not allow it.

We met with a builder yesterday who is going to work us up an estimate and plan on meeting with another one or two soon.

I am wondering what the going rate per sq. ft. you guys are experiencing?

Shop details:

Location - King George, VA about an hour South of DC

Size - 800-1000sqft

10ft ceilings

Maintenance free exterior

6/12 (possibly 5/12) roof

Poured slab and walls

200 amp service with outlets every 6 ft minimum

Also, for you guys who have a dedicated shop, what things should I consider doing that you wish you had done?

Stand by for the dust collection and table saw recommendation questions...hopefully coming real soon. :)

Thanks in advance for your help.

Re: Cost of building a garage

#2

Re: Cost of building a garage

John E. in SC

>I priced a 3-car garage last summer here in SC. I think it was to be 20x40, or 800 sq ft. It was to also include an overhanging roof off the back to park a camper under. Price at that time was $38000 if I remember correctly. Whatever it was, it was too rich for my blood, so it still hasn't been done. Good luck with your decision.

Re: Cost of building a garage

#3

Re: Cost of building a garage

Rob Hix - King George, VA

>Josh,

Sorry I have no idea about the garage, but I too live in King George. We should get together sometime and share horror stories and idea.

Feel free to e-mail.

Rob Hix

Re: Cost of building a garage

#4

Re: Cost of building a garage

Barry Irby

>I also live in VA, but in Chester. I have thought of building a garage, but it has not happened, so I can't help you with pricing.

I would suggest you plan the layout carefully and run some conduit in the floor and in particular run a DC pipe for the table saw in the floor. I wish I did not have to step ove the DC pipe to My TS.

Re: Cost of building a garage

#5

JL

Re: Cost of building a garage

JL

>Consider having a "3/4" bathroom (toilet, sink, shower) put in. A friend of mine has such in his shop. The toilet and sink get used fairly often. I can see a use for the shower after dusty or annoying work.

I would definitely consider having a utility sink put in.

Re: Cost of building a garage

#6

Re: Cost of building a garage

Ernie Miller

>Slop sink is a must if at all possable. I love mine.

Re: Cost of building a garage

#7

Re: Cost of building a garage

Larry Clinton At Frankfort (Central)., Indiana

>Hi Josh, I built a dedicated 30' X 30' story & 1/2 shop about 4 years ago in preparation for my retirement. My son's & I built the shop so can't comment on contractor costs - the only item I contracted was the smoothing of the cement floor at $500. I ended up with about $30,000 in the shop, with Central Air and High efficiency Natural gas furnace installed in the upstairs of the shop. At the time I wanted plenty of electrical outlets - so I installed about 70 - 80. These are on the walls, every 32" or less 4 1/2' above the floor and three rows across the ceiling for lights. These are on several different circuits of a 100 amp entrance fed underground from my home. If I had it to do over I would have installed a larger entrance (150 amp) or additional load center, so I could have more circuits as I used every circuit in the 40 space box. I also installed 10 or 12 individual 220 V outlets for my Compressor, welder, Unisaw etc. However, since retiring I have upgraded many of my stationary tools and really wish I had installed more 220 v instead of quite as many 120 v outlets. I now have a Jointer, planer, Unisaw, Compressor, Welder, dust collector, Surface grinder and Band saw that require 220. Other things I did were to build using 2 x 6 walls on 16" center. The cost of the 2X6's VS 2X4's was $200 to $400 and I have much better insulation in the walls. I can also support any item on the walls I wish without worry. I purchased roof trusses which were designed to allow a room upstairs, this is very cheap space as the trusses cost about $3,000 total. Maybe added $500 to the trusses + the cost of the attic ladder, flooring, ceiling & wall covering upstairs - total probably less than $2000 for a 10' wide, 30' long room with 8' ceiling (knee-walls are about 2' on each edge. I store all my excess wood in the upstairs, and have the furnace / air up there. I super insulated the structure, I keep the temp at 55 to 60 deg when I am not working and 70 when in the shop. I estimate Cost of heating to be around $60 - $100 a month in coldest months (central Indiana) and Air conditioning at about $30 month. The more insulation the better! I installed 3 (thermopane) windows downstairs, and 2 up. Kinda wished I had installed a couple more downstairs for more natural lighting, as I age I find I need more light. My ceiling height is right at 10' - If I had it to do over again, I would have laid another row of blocks and raised it to at least 10' 8", although there has only been a couple times I would have noticed the lack of height. I did install 4 separate switches for lighting, I have 6 incandescent (halogen true color) bulbs on one circuit, and 3 rows of florescent 4' lights (plugged into ceiling outlets) on individual switches. I really like the option of lighting individual areas. I drywalled the interior of my shop - finished and painted - and would do that again as it is easy to repair dings etc. and is a better fire barrier.

Re: Cost of building a garage

#8

FWIW, I had a detached garage/shop

Mike Farinella

>built here in SW Nevada a year ago. It is 24 X 40, 10 ft ceiling, and cost $22k. Does NOT include electrical, drywall, insulation and plumbing.


img

Re: Cost of building a garage

#9

Re: Cost of building a garage

Jesse in New Mexico

>I used to live in the VA/DC area and I still remember the heat and humidity. You will enjoy the shop a lot more if you plan for air conditioning!

Re: Cost of building a garage

#10

Re: Cost of building a garage

Ray Newman

>FWIW: In �01, we were in a similar situation: new house & new shop (30�x36�), as well as retirement. Depending upon your expertise & energy level (as well as a high frustration toleration), you maybe able to do some of the work yourself. Here�s a few thoughts based on our experiences�.

1.)Check w/ the local bldg dept about any restrictions as to the size of any out bldgs. If you�re bldg in a community, also check on CCR�s, ordinances, etc. Don�t take a contractor�s or a Realtor�s word�they are out to sell property.

2.)Design the shop to fit in w/ the house�same roof design & materials, same siding, windows, etc. This will also enhance the value of your property. In our 7 home development, we were the only ones to do this. A few other homeowners have built out buildings/shops/extra garages w/o thought to design, overall size, materials, etc., & it shows. Thank God I don�t have to look @ them. Our shop is located so I can look @ the driveway when the door is open, & all tools face the driveway�so no one approaches unnoticed�.

3.)Insulate the bldg w/ the maximum amount of insulation possible. Insulation is cheap compared to ever increasing energy costs. As one poster said, frame w/ 2X6. Install highly efficient windows. Make sure the slab is insulated & has a moisture barrier. If you plan for a roll-up door, get an insulated unit & a garage door opener. Makes a world of difference when it�s raining & you need to load/unload.

4.)Install a highly efficient heat/cooling(?) system. I installed a � Hot Dawg� ceiling mounted 75K BTU propane fired furnace controlled by a low temperature thermostat. It does not have a standing pilot light. System takes air from shop to keep the fire going. Fumes & water vapor vented outside. I keep it at 45-50 degrees in the. Since I use water finishes, there is no real problem w/ this unit. The fan will throw the warm air 40 plus feet & in no time the shop is up to 65 degrees or so when I work there.

5.)Security. Windows about 5-6� from the floor keep our prying eyes. Will also provide more storage room underneath the windows. Have shop wired for telephone & alarm system. Install a phone that can be reached from siting on the floor & has the keypad in the handset. This way if you injure yourself and can reach the phone, you can use it. An intercom hooked up to the house might be worthwhile. I consider TV & a computer to be a dangerous distraction.

6.)Electrical: receptacles 50-52� above floor --sheet goods will not block them. If you have children/grandchildren, it might be worth while to install a master cut out to for all but the lights when you�re not there. Put in a large shop panel in a convenient location. Take pictures of wiring before closing up walls. Had the electrician install a 220V 50 amp for a future welder if I ever get one.

7.)Lights: if installing florescent, look @ Fine Wood Working, # 153, Winter 2001/2002, which has an article on the high efficient T8 lights & how to plan lighting needs. Put lights in a series of switches/banks so you don�t illuminate the whole shop when you don�t need to. Skylights (speaking from personal experience w/ prior residence here) are nice, but they are a place where leaks can/will start, are hard to seal up (if they open) & depending on size, are an invitation for miscreants to enter your property.

8.)Wood floor is more comfortable & tool friendly.

9.)Make a large scale drawing of the shop & cardboard cut outs of the tools & benches. Really helps to aid in tool placement for efficient workflow.

10.) #9 will help you plan for an efficient dust collection system, which is a God-send if you work when the shop is closed up. You might consider a separate room for the DC & air compressor to deaden the noise. Some choose to vent the dust outside, but some localities prohibit this & you�ll also being removing warm/cool air from the shop.

11.)Interior walls/ceiling: I like drywall painted white to reflect light. Shop cabinets are hung via French cleats. Ceiling ht. is a matter of preference & what you intend 2 do.

12.)Keep the shop only for you. My spouse & I agree that I don�t put anything in her doll studio & she doesn�t or temporarily place anything in my side of the shop. The �temporary� & seasonal storage items never leave. This has happened to a neighbor.

13.)Our shop was plumbed for a bathroom, but only a deep �slop� sink was installed. If you have a bathroom, the tax assessor will love you.

14.)If you have walkways placed around the house & shop, install 4� or even larger diameter PVC pipe in the ground @ the corners & other locations before the concrete is poured. That way you always have access if you want to run an irrigation system, outdoor lighting, etc.

(Saw a shop about 10� from the garage & the owner had a buried piece of 6� PVC connecting the 2. In the pipe, he snaked an air compressor hose, so he could fill the truck tires w/o moving the vehicles outside.)

Re: Cost of building a garage

#11

Re: Cost of building a garage

Verne in Northeast NJ

>Some great ideas for a shop garage.

We just looked at a house that would've required a garage had we bought it. Friends had just built a new detached 2 car garage, with electrical, no isulation, exterior to match main house for $40K. They had the roof pitched steeply to allow ample storage above the garage.

Of course, this is Bergen County NJ, so the price is probably skewed higher than other parts of the country.

Re: Cost of building a garage

#12

Re: Cost of building a garage

AJ in Ohio

>I restored a 100 year old barn for a work shop in 2002. The one thing that I would do different is to add heating in the concrete floor. I have six windows one the first floor for plenty of natural light, the second floor is just used for storage. The foot print of the barn is 36 x 24 and aat times I wish it was bigger. One of these days i'm going to get off my back side and send some pictues. I just ran across this web site about a month ago and I think its great.

Re: Cost of building a garage

#13

Re: Cost of building a garage

Warren Muse, Earlysville VA

>I think the poured walls are going to run your costs up considerably.

Also they'll make it harder to expand, move doors, windows, etc.

Do you mean the full 10' would be poured concrete, or just 2' stem walls? Stem walls will make it easier to site the building on slope and allow you to make your 10' ceiling height with 8' studs, drywall, etc.

Re: Cost of building a garage

#14

Re: Cost of building a garage

Josh in VA

>Thanks for all of the advice/ideas/comments. Re-affirms some thoughts and advice given by some.

As far as 220 circuits. I plan on running that exterior of the walls in conduit in case I ever want to move tools, add tools, etc... I can move the circuit as needed.

The 10' ceiling include a 2' stem wall. We have a sloping yard hence the poured route.

I will keep you guys updated as things progress.

Thanks

Josh

Re: Cost of building a garage

#15

Re: Cost of building a garage

Gilles in Lachenaie PQ Canada

>I built my 18 x 28 woodshop in 2001, I did it with some friends (a lot of beer abd pizza...). It cost around $14k cnd ($10k usd).

Concreate slab with 2x6 insulated construction, 100amps panel with 17 electrical outlets, phone, beer fridge,

It took me 2 months from start to finish

tks

Gilles


img

Re: Cost of building a garage

#16

Remember to allow for shrinkage

BobG

>In my experiance garages/shops seem to shrink, rapidly the first year and then a little more each year (Kinda like wool socks)