Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

single sided veneer without warping

Posts

single sided veneer without warping

#1

single sided veneer without warping

Wayland

>Hi Folks-

I want to cement some quarter sawn sycamore veneer to 1/2" baltic birch plywood, and, for several reasons, don't want to veneer both sides. These will be doors (about 20" long) so I don't want a lot of warp. I am wondering if there are any tricks to get the sandwich not to warp. In the past, it always warped concave on the veneer side, so I thought of compensating by clamping it with a thin stave under it to warp it in the opposite direction while the glue is drying. Another alternative, maybe (and this is where your experience comes in), is to use some hydrophobic cement (I've been using yellow gule up till now) such as contact cement which will not warp (or will it; I don't know???) as long as the two pieces are not warped to begin with (which they are not).

Thanks in advance for your help.

Wayland

Re: single sided veneer without warping

#2

Re: single sided veneer without warping

John in New Mexico

>I've done it two ways, though never on a door, there's probably many others.

I prefer plastic resin glue, though it can be a pain to clamp up in sheet applications if you don't have a vac-bag. I've also used the iron on technique with yellow glue. Its applied to both halves, and left to dry for an hour or so. It will then iron together. It actually works, though I'm still not sure how far I'd trust it.

You could also try 2 hour epoxy like West System, makes great veneer glue.

John

Re: single sided veneer without warping

#3

Re: single sided veneer without warping

Art Liebeskind

>We wish it is so but it ain't. Particularly for 1/2" ply. You must balance the veneer with something similar on the back./

art liebeskind

Re: single sided veneer without warping

#4

Rick L

Re: single sided veneer without warping *LINK*

Rick L

>Noted studio furniture artist John Cederquist has been been gluing 1/4" veneer to 1/2" baltic birch on one side for a number of years with no problems. Not sure what he uses for glue but I would not use water based glues for this or contact cement. There was a good article on his technique in www.woodwork-mag.com a few years ago. The best wood mag out there in my opinion.


Unibond

Re: single sided veneer without warping

#5

Re: single sided veneer without warping

Ted Wong

>Rick, there is a difference between veneering which is what the original post is asking about and laminating which is more akin to what you have mentioned. At 1/4" the "veneer" you refer to is really not veneer at all because it behaves more like a solid piece of wood and has the resistance to bending that a thinner piece of material does not have. That is why he can get away with laminating to one side only without detrimental effects.

In the case of veneering a single side of plywood it goes against common practice of "balancing" the panel. Of course you can do anything you want and maybe it'll work and maybe it won't. But if you follow common practice I'd say your chances of success will be greater. And I would definitely not use contact cement.

Re: single sided veneer without warping

#6

I wonder if BB plywood helps?

John in New Mexico

>I've used 1/16th veneer on 1/2 BB- one side- and against my better judgement at the time. I wonder if roughly similar ply thickness and properties (hardwood rather than pine or whatever) helps it behave?

I did once veneer a dry piece of 2x doug fir with 1/16" cherry, and got a truly astounding -about 2" over 7'- bow after about 2 hours. Glued poplar on the other side- bow goes away.

John