Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Wood Shop Sound Proofing

Posts

Wood Shop Sound Proofing

#1

Wood Shop Sound Proofing

Bruce Evans

>I am in the process of expanding my wood shop to encompass most of the basement and in doing so have a unique opportunity to get some remodeling done at the same time. I have open joists with a tongue and groove sub-floor overhead (hardwood on top of that)and a wonderful wife who hears all from below!

My thought was to use Homasote and attach it to the underside of the sub-floor and then caulk it at the seems and joist edges. All the exposed wood and Homasote would then get a liberal dose of white paint and the lights would follow - using the cavities to keep them recessed and out of harm's (i.e. me with a board) way.

I should stop much of the high end frequency noise, some fumes from going up and stop the dust that sometimes sifts down from above.

My questions is concerning placement of the Homasote panels. Are they better glued/screwed to the sub-floor or should I use strapping and create an air space between the two? Perhaps there will be nominal difference between the methods - but I am counting on you to help me decide - strap or not to strap, that is the question.

Thanks in advance for the input!

Re: Wood Shop Sound Proofing

#2

Re: Wood Shop Sound Proofing

Pete LaBelle

>Sound is made up of various energy waves in the air that are transmitted to objects around them. These waves can excite those objects and create a transmitter out of them to move noise to another room by creating a "speaker" out of the wall.

First line of defence is to seal up any crack or hole, which will allow sound waves a direct "leak" into adjacent rooms (notice how much louder your car interior is with a window open only 1/32" ?. This could be done stuffing fiberglass insulation and or the "foam-in-a-can" products. Next is to create areas to dissapate waves before they get excite the outer surface of a wall. Fiberglass insulation, foam rubber (not very fire-proof though) and other soft fiber material matts do a good job of this.

For lower frequency sound absorbing, I have seen the inner skin of the sound generating room actually suspended by absorbing materials so the sound waves cannot be transmitted into a wall. Wood shops normally don't have this frequency to deal with.

Be careful of your sheeting inside of your shop. Smooth hard surfaces (like drywall) do a good job of reflecting the sound, but your shop will become louder as a result of it. The more porus the sheeting material is, the more sound it will absorb.

A basement shop will rarely ever be totally soundproof to upstairs occupants, but it can be made better with minimal effort.

You mentioned odors & fumes. In my basement shop, I have a small squirrel cage fan (impeller is about 6" diameter) that is hung from the ceiling with rubber mounts and exhausts outside thru a dryer vent kit. This keeps the room slightly negatively pressured from the rest of the house. Does a good job keeping dust and fumes from escaping to other parts of the house.

Hope this helps.

Pete

Re: Wood Shop Sound Proofing

#3

Strapping...

Jason Roehl in Mulberry, IN

>Whatever panels you hang for the ceiling surface, you'll need some sort of "break" between them and the joists. I've seen articles in a construction mag (JLC or FHB) that discuss using some sort of z-channel strapping if I recall correctly--it's been a few years. Otherwise, that ceiling material would become a drum. With vertical walls, you can build them with 2x6 top and bottom plates, then 2x4s staggered 12" O.C., with insulation either woven between or filling from both sides, plus caulking the plates to the floor and ceiling, as well as the drywall to the floor. You probably also want a solid-core (vs. foam-core) exterior entry door as the door to the basement shop, as that will greatly help mitigate the noise.

I'm in a fair number of new-construction houses, and I always hate seeing hollow-core doors go on bathrooms--you can hear "everything" that goes on inside. A solid-core door helps immensely. I had to chide a carpenter once because the door order was a mix of hollow- and solid-core doors. He had hung the solid-cores mostly on closets and the hollow-cores on the bedrooms and baths. Last name Ron, first name Mo.

Jason

Re: Wood Shop Sound Proofing

#4

Re: Wood Shop Sound Proofing

Thomas Skaggs, Foothills of Mount Level

>If you have central air/heat then remember that ducts can be sound carriers too so you may want to factor some way of isolating sound from them.

Tom

Re: Wood Shop Sound Proofing

#5

There's an article in.....

Nat Robison

>the Jan. '07 issue of Fine Homebuilding that deals with soundproofing a room. A lot of caulk and spray foam and some specialized materials.

Re: Wood Shop Sound Proofing

#6

Does Homasote Count as a Ceiling?

SanMan

>If so you may be inadvertantly finishing this space off which will up your taxes if reveiwed later on as a house assesment.

If Barry Irby's around, (our resident house inspector champion) I wonder if this is true?

SM