Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Need resawing help

Posts

Need resawing help

#1

Need resawing help

Ken Krawford

>I'm getting ready to resaw some 8/4 Jatoba. The pieces are roughly 6-7" wide and 6 ' long. I have a 14" Delta saw with riser and the blade is a Timberwolf 1/2" 3tpi. I need to cut these pieces down to 5/4.

I've tried many techniques but always seem to end up with a cut that goes slightly diagonal instead of perpendictular to the table. Yes, I've checked the blade for squareness to the table. I've tried with and without a fence. I've tried the Suffolk method of blade tensioning.

Any thoughts or suggestions would be much appreciated.

Re: Need resawing help

#2

Re: Need resawing help

Thomas Skaggs, Foothills of Mount Level

>Make sure you don't feed too fast. Keep it slow. Too fast can cause an errant blade.

Tom

Re: Need resawing help

#3

Agree and ...

Ed Mulligan, Cape Cod

>If you have a table saw begin the cut by kerfing both edges of the jatoba an inch or so. The bandsaw blade will tend to track in the tablesaw kerfs.

Ed

Re: Need resawing help

#4

Re: Need resawing help

Paul Waddle

>Question: does the diagonal always slope the same? If it does,when actually resawing,the blade or the piece is slightly tilting(bending). I would think its the feed pressure bending the blade.

The only suggestions I have are: really tension the blade, and use a thick board clamped to one you are cutting so as to make the 'edge' more stable. As already suggested,slow the feed down.

If this doesn't work,try a single point fence. Once you discover what is taking place,make the necessary corrections.

Practice on some popular or other hardwood until you get the hang of it,you won't want to waste valuable wood.Contrary to what is believed,good resawing takes practice,and watching how the blade tracks. This is just my opinion from resawing walnut-not as difficult as your material.

Re: Need resawing help

#5

Re: Need resawing help

James Fox

>Also check that the blade is tracking dead center of the top wheel.

James

Re: Need resawing help

#6

Re: Need resawing help

Jim Dillon

>Ken,

While building a hutch made from jatoba (Shop Shot #762) I was faced with having to resaw a lot of 4-10 wide jatoba; the 10 inch wide stuff was 8/4. I tried a brand new 1/2 inch 3-4 TPI Timberwolf and Woodslicer. No go. Even going very slowly, by the time I was 1 inch into the wood (especially the 10 inch stuff) the drift was huge. I then tried a Lenox Trimaster carbide tipped 1/2 inch blade and it easilycut the wood with virtually no drift and a reasonably smooth surface. I have a modest setup: Delta 14 inch, 1 1/2 hp, riser, aftermarket tension spring and that is it. Granted, I wasn't going gangbusters through the wood (say 3-4 inches/min on the wide stuff). I have also used the method suggested by Ed and that has worked just fine as well. There was a thread in the past day or so on the Lenox bandsaw blade that might be helpful. Having said all this, there have been reports of the Lenox blade breaking prematurely at the weld when used on smaller bandsaws like the 14 inchers. Mine did as well, but only after a LOT of resawing of the jatoba. I got another one as I liked the blade so much. Anyway, good luck.

Jim

Re: Need resawing help

#7

Re: Need resawing help - second fence

Jim Swank

>When your cut goes slightly diagonal, is it the blade or is the wood turning on its edge? That's what was happening to me, regardless of blade, though I never tried the Lennox. I've got a 14" Jet with riser, and the aluminum fas-trac fence system from Woodcraft.

I've now added a second fence, about 3/4" thick piece of wood with a rounded point on the other side of the blade. I clamp that in place with a small C-clamp. It holds the bottom of the board against the main fence and still allows me to adjust as needed to guide it.

There may be better ways, but this is quick and dirty and works well

Re: Need resawing help

#8

freehand

bill tindal, E.TN

>this works for me. I set the fence at say 1" from the blade. Then I scribe a line on the top of the board at 1". Then I shove it through keeping the bottom of the board against the fence and by adjusting the board I keep the scribe line just inside the kerf. No doubt there are more elegant ways but this always works.

Re: Need resawing help

#9

Re: Need resawing help

Kelby

>Have you aligned the fence to the blade? The diagonal cut can definitely happen if your fence is not properly aligned.

Re: Need resawing help

#10

Yes! Yes! Yes! Great blade choice. I have been

Art Silva

>using this blade since 1999 and it never quits. You're right, it will probably break before it wears out, and when it does I will have it re-welded.

Re: Need resawing help

#11

Thanks everyone - I got it!

Ken Krawford

>Thanks for all the replies. I'm not sure exactly what made the difference but I suspect Ed's suggestion about cutting a kerf in the top and the bottom was it. I got a super cut that required little planing.