Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Making bent lamination form.

Posts

Making bent lamination form.

#1

Making bent lamination form.

Bri in Mtl

>Most of my bent laminations have been done by simply having lots of clamps to a single form.

I'd like to make a form that has 2 halves(male/female?)

The bent laminations required are 3/8" thick, 2" wide, 3 ft long and are S-shaped. (Think back splats for a chair.)

I've already glued up some plywood for the rough form 2-1/2" thick. Can I simply make a S shaped cut in the ply form to split it and that's it?

OR do I somehow have to remove 3/8" in the cutting of the form so that when I clamp the 2 halves together the pressure will be even.

If so how to I remove the 3/8"? What type of router bit do I need? I can't figure out the process.

TIA

Re: Making bent lamination form.

#2

Rick L

Re: Making bent lamination form.

Rick L

>You need to remove the 3/8". Pretty simple actually. Bandsaw and sand your forst form and use a 3/8" flush trim bit to remove the material from the other from the other form. I have removed 1/2" of material and used a dense rubber of 1/16" on each form to pad it for better conforming of the wood.

Re: Making bent lamination form.

#3

Re: Making bent lamination form.

Bri in Mtl

>OK, i can visualize that but what about the form being 2-1/2" thick?

The router bit isn't that long. I assume I get a flush trim bit with the bearing on the bottom?

Re: Making bent lamination form.

#4

Alan Young

Re: Making bent lamination form.

Alan Young

>Hi Rick,

I'm not sure I am understanding this method. Maybe I'm missing something here but I don't see the need to remove 3/8" of material.

I think you could simply bandsaw the profile separating the pieces in half:


Then I'd screw the pieces together in mating form and even out the profile on a spindle sander- if avaialable.. other wise a rasp and had tools will get them the same.


Then unscrew the pieces flip them around, and place laminations between the forms and glu-away...



Alan

Re: Making bent lamination form.

#5

Re: Making bent lamination form.

Bri in Mtl

>I was thinking that with the curves the inner radius is slightly different from the outer radius when you have a material thickness. Imagine if the laminations were 1" thick.

I'd go ahead and simply try cutting down the middle and seeing for myself but I don't want to ruin the form.

Re: Making bent lamination form.

#6

Rick L

Re: Removing the middle...

Rick L

>You can use a pattern bit with the bearing on top and use a flush trim bit with the bearing on the bottom to finish it up. If it's a very slight curve you could just split the pattern in half but the rule of thumb in most cases is to remove the thickness of material you will be clamping in the middle or it just won't clamp evenly. It's more critical with thicker pieces and more pronounced curves. Draw it out on some paper to test it out and bring the edges together to visualize it. Mock ups are cheap and prevent mistakes

Re: Making bent lamination form.

#7

Re: Making bent lamination form.

Marym

>I remove the material to be sure to get a good fit. You could first make a template on 1/4" thick stock of the curve. Then use a straight router bit 3/8" dia with a guide bushing to make the cut through the stock. If you dont have a router bit that will cut that deep, you could bandsaw the part in half, and then offset the template on the cut piece, and use a flush trim bit to clean up and get the fit you are looking for.

Re: Making bent lamination form.

#8

Re: Making bent lamination form.

Carol from AZ

>Maybe this will help.

If you had a 4" outside radius and you added 3/8" to it you would noow have a 4-3/8" outside radius. The left over 4" inside radius from the original cut would no longer fit the now larger outside radius.

The easiest way to do this is to make templates. This is a process derived from complimentary template routing. I have a detailed explanation of the process in my book, "Router Joinery Workshop." I love for you to buy one, but you may be able to get it at the library. It was selected by the Library Journal as a book that libraries ought to buy.

I no longer stock them, so you will need to go to Amazon or wherever you buy books.

Re: Making bent lamination form.

#9

Another angle would be to make the two parts

Don Henthorn

>to your form and then join them by two pieces of strap iron at each end a short distance from the end. Make the straps long enough that that there will an additional inch between the laminations and the other half of the form. The straps on the top of the form should be attached by nuts so that the upper half of the form can be removed while stacking the laminations. Next get a piece of three inch fire hose long enough to cover the laminations and enough extra length to be able to fold over and clamp at the ends. Get an small diameter motor bike inner tube and cut it in two about six inches from the valve. Make a hole for the valve in the inner tube the same distance from one of the ends and put the inner tube in the hose with the valve through the hole. Epoxy the outside of the hole in the hose to keep it from fraying. Take some 1/2" square metal bar and cut into four pieces each of which is a 1" longer than the width of the flattened hose. Drill 3/16" holes centered 3/16" from each end of the four pieces and use stove bolts to clamp two of these together over the folded ends of the inner tube in the hose. Check to be sure you have made the inner tube-fire hose assembly long enough to go in the form and cover all the laminations. Then do a dry run going the following steps but don't apply the glue or inflate the tube: Put the top form on and bolt it tight. Then apply the glue and put the laminations in the form and set the inner tube-firehose unit on top with the valve in a position that can be easily reached. Make sure everything is aligned as best you can and inflate the tube to 60 lbs pressure. If everything went well repeat the procedure and apply the glue and inflate the tube. Adding a strip of thin sheet metal on top of the laminations as a caul may help, but I never found I needed it.

The same procedure will work for narrower laminations only use a bicycle inner tube and a smaller fire hose.

No guarantees. Worked for me quite a few times.

Re: Making bent lamination form.

#10

Sorry. The top form of couse can't go

Don Henthorn

>on until AFTER you have put in the laminations and the inner tube-fire hose unit. My bad.